[PATCH v11 3/3] mtd: spi-nor: spansion: Add s25hl-t/s25hs-t IDs and fixups
Tudor.Ambarus at microchip.com
Tudor.Ambarus at microchip.com
Wed Apr 20 01:11:39 PDT 2022
On 4/20/22 10:50, Takahiro Kuwano wrote:
> EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
>
> On 4/20/2022 4:47 PM, Tudor.Ambarus at microchip.com wrote:
>> On 4/20/22 10:35, Tudor Ambarus - M18064 wrote:
>>> On 4/20/22 09:58, Takahiro Kuwano wrote:
>>>> EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
>>>>
>>>> On 4/20/2022 3:11 PM, Tudor.Ambarus at microchip.com wrote:
>>>>> On 4/20/22 08:34, Takahiro Kuwano wrote:
>>>>>> EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
>>>>>>
>>>>>> Hi Tudor,
>>>>>>
>>>>>> Thank you for your feedback.
>>>>>>
>>>>>> On 4/19/2022 6:32 PM, Tudor.Ambarus at microchip.com wrote:
>>>>>>> On 4/18/22 08:41, tkuw584924 at gmail.com wrote:
>>>>>>>> EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
>>>>>>>>
>>>>>>>> From: Takahiro Kuwano <Takahiro.Kuwano at infineon.com>
>>>>>>>>
>>>>>>>> The S25HL-T/S25HS-T family is the Infineon SEMPER Flash with Quad SPI.
>>>>>>>>
>>>>>>>> For the single-die package parts (512Mb and 1Gb), only bottom 4KB and
>>>>>>>> uniform sector sizes are supported. This is due to missing or incorrect
>>>>>>>> entries in SMPT. Fixup for other sector sizes configurations will be
>>>>>>>> followed up as needed.
>>>>>>>>
>>>>>>>> Tested on Xilinx Zynq-7000 FPGA board.
>>>>>>>>
>>>>>>>> Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano at infineon.com>
>>>>>>>> ---
>>>>>>>> Changes in v11:
>>>>>>>> - Cleanup fixups based on other patches in this series
>>>>>>>>
>>>>>>>> Changes in v10:
>>>>>>>> - Cleanup fixups and ID table based on other patches in this series
>>>>>>>>
>>>>>>>> Changes in v9:
>>>>>>>> - Use late_init() hook to fix mode clocks and writesize
>>>>>>>> - Use PARSE_SFDP instead of NO_SFDP_FLAGS
>>>>>>>> - Use MFR_FLAGS for USE_CLSR
>>>>>>>> - Add comment block to explain about addr mode in post_bfpt_fixups()
>>>>>>>>
>>>>>>>> Changes in v8:
>>>>>>>> - Call write_disable in error case only
>>>>>>>> - Use spi_nor_read_reg() helper
>>>>>>>> - Use nor->bouncebuf instead of variable on stack
>>>>>>>> - Update ID table to use FLAGS macro
>>>>>>>>
>>>>>>>> Changes in v7:
>>>>>>>> - Add missing device info table in v6
>>>>>>>>
>>>>>>>> Changes in v6:
>>>>>>>> - Remove 2Gb multi die pacakge support
>>>>>>>>
>>>>>>>> Changes in v5:
>>>>>>>> - Add NO_CHIP_ERASE flag to S25HL02GT and S25HS02GT
>>>>>>>>
>>>>>>>> Changes in v4:
>>>>>>>> - Merge block comments about SMPT in s25hx_t_post_sfdp_fixups()
>>>>>>>> - Remove USE_CLSR flags from S25HL02GT and S25HS02GT
>>>>>>>>
>>>>>>>> Changes in v3:
>>>>>>>> - Remove S25HL256T and S25HS256T
>>>>>>>> - Add S25HL02GT and S25HS02GT
>>>>>>>> - Add support for multi-die package parts support
>>>>>>>> - Remove erase_map fix for top/split sector layout
>>>>>>>> - Set ECC data unit size (16B) to writesize
>>>>>>>>
>>>>>>>> drivers/mtd/spi-nor/spansion.c | 54 ++++++++++++++++++++++++++++++++++
>>>>>>>> 1 file changed, 54 insertions(+)
>>>>>>>>
>>>>>>>> diff --git a/drivers/mtd/spi-nor/spansion.c b/drivers/mtd/spi-nor/spansion.c
>>>>>>>> index 493240ebfd70..dd37b829efbc 100644
>>>>>>>> --- a/drivers/mtd/spi-nor/spansion.c
>>>>>>>> +++ b/drivers/mtd/spi-nor/spansion.c
>>>>>>>> @@ -208,6 +208,44 @@ static int cypress_nor_set_page_size(struct spi_nor *nor, u8 addr_width)
>>>>>>>> return 0;
>>>>>>>> }
>>>>>>>>
>>>>>>>> +static int
>>>>>>>> +s25hx_t_post_bfpt_fixups(struct spi_nor *nor,
>>>>>>>> + const struct sfdp_parameter_header *bfpt_header,
>>>>>>>> + const struct sfdp_bfpt *bfpt)
>>>>>>>> +{
>>>>>>>> + int ret;
>>>>>>>> +
>>>>>>>> + /*
>>>>>>>> + * From BFPT, the nor->addr_width is set to 3. In Read Any Reg op, the
>>>>>>>> + * Flash takes 3-byte or 4-byte addr depending current addr mode. Since
>>>>>>>> + * Read Any Reg op is called in this hook and SMPT parse, we would sync
>>>>>>>
>>>>>>> Hi, Takahiro,
>>>>>>>
>>>>>>> I would like some details, please.
>>>>>>> 1/ with "this hook" you refer to cypress_nor_set_page_size(). Why can't you use a
>>>>>>> addr_width of value 3 when reading SPINOR_REG_CYPRESS_CFR3V?
>>>>>>>
>>>>>> If we are sure that the Flash is in 3-byte address mode, we can use the value 3
>>>>>> for reading CFR3V. However, the Flash's address mode may be changed prior to
>>>>>> Linux MTD probe in some use cases. Actually, in u-boot, it is set to 4-byte
>>>>>> address mode. We need to set the Flash's address mode in known state and update
>>>>>
>>>>> addr_width is set via CFR2Volatile, can we reset the flash at probe instead? Then
>>>>> you'll be sure that the flash is in its default state.
>>>>>
>>>> Resetting the Flash to revert back to default state should work for this. However,
>>>
>>> good, let's do this.
>>>
>>>> we still have SMPT issue below.
>>>>
>>>>>> nor->addr_width accordingly. Due to SMPT issue below, value of 4 would be better
>>>>>> choice.
>>>>>>
>>>>>>> 2/ Where in SMPT parse? I looked through the code and couldn't find the Read Any
>>>>>>> Reg op used. Why do you need an addr_width of value 4 in SMPT parse?
>>>>>>>
>>>>>> In the spi_nor_get_map_in_use(), the nor->read_opcode is set to 0x65 (=Read Any Reg).
>>>>>> The spi_nor_smpt_addr_width() returns the value of the nor->addr_width due to
>>>>>
>>>>> ok
>>>>>
>>>>>> SMPT_CMD_ADDRESS_LEN_USE_CURRENT. The nor->addr_width is set to 4 in the
>>>>>> spi_nor_parse_4bait() before SMPT parse. Therefore, the host issues Read Any Reg
>>>>>
>>>>> if 4bait is parsed before SMPT and nor->addr_width is already set to 4 in parse_4bait,
>>>>> then you don't have to do anything for SMPT, right?
>>>>>
>>>> Currently 4bait is parsed before SMPT. So, if we are sure the Flash is in 4-byte address
>>>> mode (by u-boot, for example), we don't have to do anything. If the Flash is in 3-byte
>>>> address mode (default), SMPT parse does not work correctly.
>>>>
>>>> Please see this about 4BAIT and SMPT issue.
>>>> https://patchwork.ozlabs.org/project/linux-mtd/patch/20201212115817.5122-1-vigneshr@ti.com/
>>>>
>>>> I introduced another workaround for SMPT issue in my previous series.
>>>> https://patchwork.ozlabs.org/project/linux-mtd/patch/9a2d323b2c18485d13f271e3bb213b96fea0e7e1.1649641729.git.Takahiro.Kuwano@infineon.com/
>>>> I withdrew this because this does not work if Flash address mode is not default state.
>>>> But if we can reset the Flash at probe, this should work.
>>>
>>> Hmm. How about issuing spi_nor_set_4byte_addr_mode after parsing 4bait table,
>>> to solve this dependency?
>>
>> or maybe we can add a smpt hook where you interrogate the state of addr mode
>> from CR2V and use the add_width from CR2V instead of relying on what we get
>> from SMPT_CMD_ADDRESS_LEN_USE_CURRENT. This will avoid changing the state
>> of the flash at parse time.
>>
> Reading CR2V requires Read Any Reg op with correct address width.
> Chicken-and-egg...
I agree with Pratyush that we shouldn't change the state of the flash at parsing
time. So to solve this we could introduce nor->params->addr_width to set it at
parsing time, and use the default nor->addr_width for ops at parsing time for
all the parsers.
>
>>>
>>>>
>>>>
>>>>>> with 4-byte address. We need to set the Flash into 4-byte address mode in advance.
>>>>>>
>>>>>>>
>>>>>>>> + * Flash's addr mode and nor->addr_width here.
>>>>>>>> + */
>>>>>>>> + ret = spi_nor_set_4byte_addr_mode(nor, true);
>>>>>>>> + if (ret)
>>>>>>>> + return ret;
>>>>>>>> + nor->addr_width = 4;
>>>>>>>> +
>>>>>>>> + /* Replace Quad Enable with volatile version */
>>>>>>>> + nor->params->quad_enable = cypress_nor_quad_enable_volatile;
>>>>>>>> +
>>>>>>>> + return cypress_nor_set_page_size(nor, nor->addr_width);
>>>>>>>> +}
>>>>>>>> +
>>>>>>>> +void s25hx_t_late_init(struct spi_nor *nor)
>>>>>>>> +{
>>>>>>>> + /* Fast Read 4B requires mode cycles */
>>>>>>>> + nor->params->reads[SNOR_CMD_READ_FAST].num_mode_clocks = 8;
>>>>>>>
>>>>>>> Isn't this info already handled in BFPT? What value of num_mode_clocks
>>>>>>> do you obtain from BFPT for the non-4B opcode?
>>>>>>>
>>>>>> There is no parameter in BFPT that describes about Fast Read 1-1-1 op
>>>>>> (as we can see 'struct sfdp_bfpt_read' in sfdp.c).
>>>>>> The value of num_mode_clocks for Fast Read 1-1-1 is set to 0 in
>>>>>> spi_nor_init_default_params().
>>>>>>
>>>>>
>>>>> I see, thanks!
>>>>
>>>> Thanks,
>>>> Takahiro
>>>
>>
More information about the linux-mtd
mailing list