[PATCH v1 3/5] mtd: atmel_nand: Support PMECC on SAMA5D2

[Yang, Wenyou]

Hi Rob,

> -----Original Message-----
> From: Rob Herring [mailto:robh at kernel.org]
> Sent: 2016年1月14日 21:15
> To: Yang, Wenyou <Wenyou.Yang at atmel.com>
> Cc: Romain Izard <romain.izard.pro at gmail.com>; linux-mtd at lists.infradead.org;
> devicetree at vger.kernel.org; Josh Wu <rainyfeeling at outlook.com>; Ferre,
> Nicolas <Nicolas.FERRE at atmel.com>
> Subject: Re: [PATCH v1 3/5] mtd: atmel_nand: Support PMECC on SAMA5D2
> 
> On Wed, Jan 13, 2016 at 7:17 PM, Yang, Wenyou <Wenyou.Yang at atmel.com>
> wrote:
> >
> >
> >> -----Original Message-----
> >> From: Rob Herring [mailto:robh at kernel.org]
> >> Sent: 2016年1月14日 9:13
> >> To: Romain Izard <romain.izard.pro at gmail.com>
> >> Cc: linux-mtd at lists.infradead.org; devicetree at vger.kernel.org; Yang,
> >> Wenyou <Wenyou.Yang at atmel.com>; Josh Wu <rainyfeeling at outlook.com>;
> >> Ferre, Nicolas <Nicolas.FERRE at atmel.com>
> >> Subject: Re: [PATCH v1 3/5] mtd: atmel_nand: Support PMECC on SAMA5D2
> >>
> >> On Wed, Jan 13, 2016 at 05:34:15PM +0100, Romain Izard wrote:
> >> > Starting with the SAMA5D2, there is a new revision of the Atmel
> >> > PMECC controller that can correct 32 bits in each sector. This
> >> > controller is not 100% compatible with the previous revision that
> >> > corrected a maximum of 24 bits by sector, as some register addresses
> overlap.
> >> >
> >> > Using information from the device tree, we can configure the driver
> >> > to work with both versions.
> >> >
> >> > Signed-off-by: Romain Izard <romain.izard.pro at gmail.com>
> >> > ---
> >> >  .../devicetree/bindings/mtd/atmel-nand.txt         |  7 +++++--
> >> >  drivers/mtd/nand/atmel_nand.c                      | 23
> +++++++++++++++++++++-
> >> >  drivers/mtd/nand/atmel_nand_ecc.h                  |  8 ++++++--
> >> >  3 files changed, 33 insertions(+), 5 deletions(-)
> >> >
> >> > diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt
> >> > b/Documentation/devicetree/bindings/mtd/atmel-nand.txt
> >> > index 89b0db9801b0..90887b430f03 100644
> >> > --- a/Documentation/devicetree/bindings/mtd/atmel-nand.txt
> >> > +++ b/Documentation/devicetree/bindings/mtd/atmel-nand.txt
> >> > @@ -1,7 +1,10 @@
> >> >  Atmel NAND flash
> >> >
> >> >  Required properties:
> >> > -- compatible : should be "atmel,at91rm9200-nand" or "atmel,sama5d4-nand".
> >> > +- compatible: The possible values are:
> >> > +   "atmel,at91rm9200-nand"
> >> > +   "atmel,sama5d2-nand"
> >> > +   "atmel,sama5d4-nand"
> >> >  - reg : should specify localbus address and size used for the chip,
> >> >     and hardware ECC controller if available.
> >> >     If the hardware ECC is PMECC, it should contain address and
> >> > size for @@ -22,7 +25,7 @@ Optional properties:
> >> >    Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first",
> >> >    "soft_bch".
> >> >  - atmel,has-pmecc : boolean to enable Programmable Multibit ECC
> hardware.
> >> > -  Only supported by at91sam9x5 or later sam9 product.
> >> > +  Supported by AT91SAM9x5 or later SAM9 chips, and SAMA5 chips.
> >>
> >> What compatible string would AT91SAM9x5 be?
> >
> > "atmel,at91rm9200-nand".
> 
> Answer the question in the binding doc by saying which compatible strings a
> property is valid for.
> 

Thank you for your advice. I will keep in mind next time.


Best Regards,
Wenyou Yang