[PATCH v5 6/8] arm: dts: Add bcm-nsp and bcm958625k support
Jonas Gorski
jonas.gorski at gmail.com
Mon Aug 1 08:09:26 PDT 2016
Hi,
On 30 July 2016 at 00:13, Kamal Dasu <kdasu.kdev at gmail.com> wrote:
> Adding qspi node compatible with the new spi-bcm-qspi
> driver for the broadcom's northstar SoC.
>
> Signed-off-by: Kamal Dasu <kdasu.kdev at gmail.com>
> Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy at broadcom.com>
> ---
> arch/arm/boot/dts/bcm-nsp.dtsi | 33 +++++++++++++++++++++++++++++----
> arch/arm/boot/dts/bcm958625k.dts | 34 ++++++++++++++++++++++++++++++++++
> 2 files changed, 63 insertions(+), 4 deletions(-)
>
> diff --git a/arch/arm/boot/dts/bcm-nsp.dtsi b/arch/arm/boot/dts/bcm-nsp.dtsi
> index 6a40ed7..26c863e 100644
> --- a/arch/arm/boot/dts/bcm-nsp.dtsi
> +++ b/arch/arm/boot/dts/bcm-nsp.dtsi
> @@ -160,7 +160,7 @@
>
> axi {
> compatible = "simple-bus";
> - ranges = <0x00000000 0x18000000 0x0011ba08>;
> + ranges = <0x00000000 0x18000000 0x0011c40a>;
> #address-cells = <1>;
> #size-cells = <1>;
>
> @@ -206,9 +206,34 @@
> brcm,nand-has-wp;
> };
>
> - rng: rng at 33000 {
> - compatible = "brcm,bcm-nsp-rng";
> - reg = <0x33000 0x14>;
You remove the rng node, is this intentional?
> + qspi: qspi at 27200 {
> + compatible = "brcm,spi-bcm-qspi";
> + reg = <0x027200 0x184>,
> + <0x027000 0x124>,
> + <0x11c408 0x004>,
> + <0x0273a0 0x01c>;
> + reg-names = "mspi", "bspi", "intr_regs",
> + "intr_status_reg";
> + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "spi_lr_fullness_reached",
> + "spi_lr_session_aborted",
> + "spi_lr_impatient",
> + "spi_lr_session_done",
> + "spi_lr_overhead",
> + "mspi_done",
> + "mspi_halted";
> + clocks = <&iprocmed>;
> + clock-names = "iprocmed";
> + clock-frequency = <12500000>;
> + num-cs = <2>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> };
>
> ccbtimer0: timer at 34000 {
> diff --git a/arch/arm/boot/dts/bcm958625k.dts b/arch/arm/boot/dts/bcm958625k.dts
> index 2d84226..ab7ba8f 100644
> --- a/arch/arm/boot/dts/bcm958625k.dts
> +++ b/arch/arm/boot/dts/bcm958625k.dts
> @@ -126,3 +126,37 @@
> groups = "nand_grp";
> };
> };
> +
> +&qspi {
> + bspi-sel = <0>;
> + flash: m25p80 at 0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "m25p80";
> + reg = <0x0>;
> + spi-max-frequency = <12500000>;
> + m25p,fast-read;
> + spi-cpol;
> + spi-cpha;
> +
> + partition at 0 {
> + label = "boot";
> + reg = <0x00000000 0x000a0000>;
> + };
these should be enclosed by a partitions node with compatible
"fixed-partitions", see
Documentation/devicetree/bindings/mtd/partition.txt.
> +
> + partition at 1 {
The address is 0xa0000 so this should be partition at a0000.
> + label = "env";
> + reg = <0x000a0000 0x00060000>;
> + };
> +
> + partition at 2 {
likewise.
> + label = "system";
> + reg = <0x00100000 0x00600000>;
> + };
> +
> + partition at 3 {
etc.
> + label = "rootfs";
> + reg = <0x00700000 0x01900000>;
> + };
> + };
> +};
Regards
Jonas
More information about the linux-mtd
mailing list