[PATCH 2/2] mtd: spi-nor: Add Pm25LD020 and GD25Q41B chip ID.

[Marek Vasut]

On Tuesday, July 28, 2015 at 05:22:17 PM, Rafał Miłecki wrote:
> On 28 July 2015 at 16:33, Marek Vasut <marex at denx.de> wrote:
> > On Tuesday, July 28, 2015 at 11:07:58 AM, Michal Suchanek wrote:
> >> First chip reads Pm25LD020 or Pm25L0020. Found on some WD HDD PCB.
> >> Identified as PMC Pm25LD020.
> >> Flash read does not return consistent data which explains why the disk
> >> died.
> >> 
> >> Second chip reads something like 25Q41BT. Found on Esspif ESP8266 based
> >> ESP-01 board. Identified as Giga Devices GD25Q41B.
> >> 
> >> Signed-off-by: Michal Suchanek <hramrach at gmail.com>
> >> ---
> >> 
> >>  drivers/mtd/spi-nor/spi-nor.c | 2 ++
> >>  1 file changed, 2 insertions(+)
> >> 
> >> diff --git a/drivers/mtd/spi-nor/spi-nor.c
> >> b/drivers/mtd/spi-nor/spi-nor.c index cba3bd0..e55689d 100644
> >> --- a/drivers/mtd/spi-nor/spi-nor.c
> >> +++ b/drivers/mtd/spi-nor/spi-nor.c
> >> @@ -558,6 +558,7 @@ static const struct spi_device_id spi_nor_ids[] = {
> >> 
> >>       { "mb85rs1mt", INFO(0x047f27, 0, 128 * 1024, 1, SPI_NOR_NO_ERASE)
> >>       },
> >>       
> >>       /* GigaDevice */
> >> 
> >> +     { "gd25q41b", INFO(0xc84013, 0, 64 * 1024,  8, SECT_4K) },
> >> 
> >>       { "gd25q32", INFO(0xc84016, 0, 64 * 1024,  64, SECT_4K) },
> >>       { "gd25lq32c", INFO(0xc86016, 0, 64 * 1024,  64, SECT_4K) },
> >>       { "gd25q64", INFO(0xc84017, 0, 64 * 1024, 128, SECT_4K) },
> >> 
> >> @@ -601,6 +602,7 @@ static const struct spi_device_id spi_nor_ids[] = {
> >> 
> >>       /* PMC */
> >>       { "pm25lv512",   INFO(0,        0, 32 * 1024,    2, SECT_4K_PMC)
> >>       }, { "pm25lv010",   INFO(0,        0, 32 * 1024,    4,
> >>       SECT_4K_PMC) },
> >> 
> >> +     { "pm25ld020",   INFO(0x7f9d22, 0, 64 * 1024,    4, SECT_4K) },
> >> 
> >>       { "pm25lq032",   INFO(0x7f9d46, 0, 64 * 1024,   64, SECT_4K) },
> >>       
> >>       /* Spansion -- single (large) sector size only, at least
> > 
> > You might want to split this into two patches, but see my comment on 1/2
> > and please wait for Brian's confirmation there before you do anything.
> 
> Since these flashes are from 2 different vendors, it may make sense to
> use 2 separated patches. I don't care too much however.
> 
> Adding these entries is OK in general.

Thanks for clarifying, I'll make sure to remember this :)

Best regards,
Marek Vasut