[PATCH 1/2] mtd: nand: support ONFI timings mode retrieval for non-ONFI NANDs

[Boris BREZILLON]

On Fri, 19 Sep 2014 21:46:07 -0700
Brian Norris <computersforpeace at gmail.com> wrote:

> Since you were asking about this series, I have a comment:
> 
> On Mon, Jul 28, 2014 at 11:16:51AM +0200, Boris BREZILLON wrote:
> > Add an onfi_timing_mode_ds field to nand_chip and nand_flash_dev in order
> > to support NAND timings definition for non-ONFI NAND.
> > 
> > NAND that support better timings mode than the default one (timings mode 0)
> > have to define a new entry in the nand_ids table.
> > 
> > The timings mode should be deduced from timings description from the
> > datasheet and the ONFI specification
> > (www.onfi.org/~/media/ONFI/specs/onfi_3_1_spec.pdf, chapter 4.15
> > "Timing Parameters").
> > You should choose the closest mode that fit the timings requirements of
> > your NAND chip.
> > 
> > Signed-off-by: Boris BREZILLON <boris.brezillon at free-electrons.com>
> > ---
> >  drivers/mtd/nand/nand_base.c | 1 +
> >  include/linux/mtd/nand.h     | 7 +++++++
> >  2 files changed, 8 insertions(+)
> > 
> > diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c
> > index d8cdf06..c952c21 100644
> > --- a/drivers/mtd/nand/nand_base.c
> > +++ b/drivers/mtd/nand/nand_base.c
> > @@ -3576,6 +3576,7 @@ static bool find_full_id_nand(struct mtd_info *mtd, struct nand_chip *chip,
> >  		chip->options |= type->options;
> >  		chip->ecc_strength_ds = NAND_ECC_STRENGTH(type);
> >  		chip->ecc_step_ds = NAND_ECC_STEP(type);
> > +		chip->onfi_timing_mode_ds = type->onfi_timing_mode_ds;
> >  
> >  		*busw = type->options & NAND_BUSWIDTH_16;
> >  
> > diff --git a/include/linux/mtd/nand.h b/include/linux/mtd/nand.h
> > index 3083c53..435c005 100644
> > --- a/include/linux/mtd/nand.h
> > +++ b/include/linux/mtd/nand.h
> > @@ -587,6 +587,7 @@ struct nand_buffers {
> >   * @ecc_step_ds:	[INTERN] ECC step required by the @ecc_strength_ds,
> >   *                      also from the datasheet. It is the recommended ECC step
> >   *			size, if known; if unknown, set to zero.
> > + * @onfi_timing_mode_ds:[INTERN] ONFI timing mode deduced from datasheet.
> 
> Might want at least one space between '[INTERN]' and 'ONFI'?

You mean between the colon and '[INTERN]', right ?

> 
> >   * @numchips:		[INTERN] number of physical chips
> >   * @chipsize:		[INTERN] the size of one chip for multichip arrays
> >   * @pagemask:		[INTERN] page number mask = number of (pages / chip) - 1
> > @@ -671,6 +672,7 @@ struct nand_chip {
> >  	uint8_t bits_per_cell;
> >  	uint16_t ecc_strength_ds;
> >  	uint16_t ecc_step_ds;
> > +	int onfi_timing_mode_ds;
> 
> I'm not sure if we'll just want a field specific to non-ONFI chips,
> faking an ONFI timing mode; can we make this into a more generally
> useful field, that represents something consistent across all NAND
> types? I was thinking a "highest mode supported", but that actually
> isn't great, since for true ONFI modes (except mode 0) require a SET
> FEATURES command to change to a higher mode.
> 
> Maybe just something like onfi_timing_mode_default, which we could then
> use as mode 0 for ONFI chips.
> 
> Ideally, we could centralize as much of this as possible, so that a NAND
> driver only has to know the mechanics of "how do I translate an ONFI
> mode to a timing configuration for my NAND controller,"

I guess you meant "how do I translate a NAND timing config given by
nand_sdr_timings to my specific NAND controller config", right ?

> instead of any
> details of how to choose from one of many supported ONFI modes. i.e., it
> could implement something like the following hook:
> 
> 	int (*set_timing_mode)(struct nand_sdr_timings *timing);

I'm not opposed to this solution (I actually think this is how it
should be done :-), and, IIRC, Jason proposed to do the same kind of
things a while ago), but this means the conversion would be done by the
NAND FW and passed to the NAND driver, and this implies reworking the
drivers already directly using ONFI modes to configure their NAND
timings to make use nand_sdr_timings instead.

Moreover, I think we should define a union to handle several kind of
timings (ddr NAND are coming :-P):

enum nand_timings_type /* or nand_bus_type or something else ;-) */ {
	SDR_NAND,
	DDR_NAND,
}

struct nand_timings {
	enum nand_timings_type type;
	union {
		struct nand_sdr_timings sdr;
		struct nand_ddr_timings ddr;
	} timings;
};

But this is another story ;-).

> 
> But anyway, that's out of the scope of this series, and it may be harder
> than I make it sound. I just wanted to throw that out there.

If you don't mind I'd like to get something simple first: just renaming
onfi_timing_mode_ds is fine, but adding the whole conversion stuff to
the core implies much more changes. And I can work on a more
integrated solution as a second step.

Let me know what you think. 

Best Regards,

Boris


-- 
Boris Brezillon, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com