[PATCH net-next v2 13/13] net: stmmac: visconti: use stmmac_get_phy_intf_sel()

[Russell King (Oracle)]

Use stmmac_get_phy_intf_sel() to decode the PHY interface mode to the
phy_intf_sel value, validate the result and use that to set the
control register to select the operating mode for the DWMAC core.

Note that this will allow GMII as well as MII as the phy_intf_sel
value is the same for both.

Signed-off-by: Russell King (Oracle) <rmk+kernel at armlinux.org.uk>
---
 .../ethernet/stmicro/stmmac/dwmac-visconti.c  | 26 +++++--------------
 1 file changed, 6 insertions(+), 20 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-visconti.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-visconti.c
index 7b6b048e1be0..9497b13a5753 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-visconti.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-visconti.c
@@ -42,10 +42,6 @@
 
 #define ETHER_CLK_SEL_RX_TX_CLK_EN (ETHER_CLK_SEL_RX_CLK_EN | ETHER_CLK_SEL_TX_CLK_EN)
 
-#define ETHER_CONFIG_INTF_MII	PHY_INTF_SEL_GMII_MII
-#define ETHER_CONFIG_INTF_RGMII	PHY_INTF_SEL_RGMII
-#define ETHER_CONFIG_INTF_RMII	PHY_INTF_SEL_RMII
-
 struct visconti_eth {
 	void __iomem *reg;
 	struct clk *phy_ref_clk;
@@ -150,22 +146,12 @@ static int visconti_eth_init_hw(struct platform_device *pdev, struct plat_stmmac
 {
 	struct visconti_eth *dwmac = plat_dat->bsp_priv;
 	unsigned int clk_sel_val;
-	u32 phy_intf_sel;
-
-	switch (plat_dat->phy_interface) {
-	case PHY_INTERFACE_MODE_RGMII:
-	case PHY_INTERFACE_MODE_RGMII_ID:
-	case PHY_INTERFACE_MODE_RGMII_RXID:
-	case PHY_INTERFACE_MODE_RGMII_TXID:
-		phy_intf_sel = ETHER_CONFIG_INTF_RGMII;
-		break;
-	case PHY_INTERFACE_MODE_MII:
-		phy_intf_sel = ETHER_CONFIG_INTF_MII;
-		break;
-	case PHY_INTERFACE_MODE_RMII:
-		phy_intf_sel = ETHER_CONFIG_INTF_RMII;
-		break;
-	default:
+	int phy_intf_sel;
+
+	phy_intf_sel = stmmac_get_phy_intf_sel(plat_dat->phy_interface);
+	if (phy_intf_sel != PHY_INTF_SEL_GMII_MII &&
+	    phy_intf_sel != PHY_INTF_SEL_RGMII &&
+	    phy_intf_sel != PHY_INTF_SEL_RMII) {
 		dev_err(&pdev->dev, "Unsupported phy-mode (%d)\n", plat_dat->phy_interface);
 		return -EOPNOTSUPP;
 	}
-- 
2.47.3