[PATCH 2/2] dt-bindings: mmc: mtk-sd: Add support for MT8196

[Rob Herring]

On Thu, Sep 26, 2024 at 03:03:18PM +0800, Andy-ld Lu wrote:
> Extend the devicetree bindings to include the MT8196 mmc controller
> by adding the compatible string 'mediatek,msdc-v2', which could be
> also used for future compatible SoCs that support new tx/rx.

Generally, every SoC ends up changing at least slightly. So we don't do 
version numbers except when there's a well defined versioning scheme of 
the h/w (e.g. FPGA IP blocks). So, use SoC for compatible string.

> 
> Add three properties for MT8196 settings:
> - 'mediatek,prohibit-gate-cg', indicate if the source clock CG could
>   be disabled when CPU access IP registers.
> 
> - 'mediatek,stop-dly-sel', configure read data clock stops at block gap.
> 
> - 'mediatek,pop-en-cnt', configure the margins of write and read
>   pointers while begin to pop data transfer.
> 
> Signed-off-by: Andy-ld Lu <andy-ld.lu at mediatek.com>
> ---
>  .../devicetree/bindings/mmc/mtk-sd.yaml       | 26 +++++++++++++++++++
>  1 file changed, 26 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/mmc/mtk-sd.yaml b/Documentation/devicetree/bindings/mmc/mtk-sd.yaml
> index c532ec92d2d9..82d1a9fac67c 100644
> --- a/Documentation/devicetree/bindings/mmc/mtk-sd.yaml
> +++ b/Documentation/devicetree/bindings/mmc/mtk-sd.yaml
> @@ -25,6 +25,7 @@ properties:
>            - mediatek,mt8173-mmc
>            - mediatek,mt8183-mmc
>            - mediatek,mt8516-mmc
> +          - mediatek,msdc-v2
>        - items:
>            - const: mediatek,mt7623-mmc
>            - const: mediatek,mt2701-mmc
> @@ -154,6 +155,30 @@ properties:
>      enum: [32, 64]
>      default: 32
>  
> +  mediatek,stop-dly-sel:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    description:
> +      Some SoCs need to set appropriate stop-dly-sel to configure read data clock
> +      stops at block gap. The valid range is from 0 to 0xf.

SoC dependent or board dependent? Imply from the compatible for the 
former. A property is fine for the latter case.

> +    minimum: 0
> +    maximum: 0xf
> +
> +  mediatek,pop-en-cnt:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    description:
> +      Some SoCs need to set appropriate pop-en-cnt to configure the margins of write
> +      and read pointers while begin to pop data transfer. The valid range is from 0
> +      to 0xf.
> +    minimum: 0
> +    maximum: 0xf

Same question.

> +
> +  mediatek,prohibit-gate-cg:
> +    $ref: /schemas/types.yaml#/definitions/flag
> +    description:
> +      Decide if source clock CG could be disabled when CPU access IP registers.
> +      If present, source clock CG could not be disabled.
> +      If not present, source clock CG could be disabled.


Sounds like you need to describe the clock in "clocks".

> +
>    resets:
>      maxItems: 1
>  
> @@ -191,6 +216,7 @@ allOf:
>              - mediatek,mt8188-mmc
>              - mediatek,mt8195-mmc
>              - mediatek,mt8516-mmc
> +            - mediatek,msdc-v2
>      then:
>        properties:
>          clocks:
> -- 
> 2.46.0
>