[PATCH net-next v12 08/18] net: ethernet: mtk_eth_soc: fix 1000Base-X and 2500Base-X modes
Russell King (Oracle)
linux at armlinux.org.uk
Sat Mar 11 12:00:20 PST 2023
On Sat, Mar 11, 2023 at 01:05:37PM +0100, Frank Wunderlich wrote:
> Hi
>
> > Gesendet: Mittwoch, 08. März 2023 um 16:24 Uhr
> > Von: "Russell King (Oracle)" <linux at armlinux.org.uk>
> > > > It would be nice to add these to my database - please send me the
> > > > output of ethtool -m $iface raw on > foo.bin for each module.
> >
> > so if you can do that for me, then I can see whether it's likely that
> > the patches that are already in mainline will do anything to solve
> > the workaround you've had to add for the hw signals.
>
> i got the 2.5G copper sfps, and tried them...they work well with the v12 (including this patch), but not in v13...
>
> i dumped the eeprom like you mention for your database:
>
> $ hexdump -C 2g5_sfp.bin
> 00000000 03 04 07 00 01 00 00 00 00 02 00 05 19 00 00 00 |................|
> 00000010 1e 14 00 00 4f 45 4d 20 20 20 20 20 20 20 20 20 |....OEM |
> 00000020 20 20 20 20 00 00 00 00 53 46 50 2d 32 2e 35 47 | ....SFP-2.5G|
> 00000030 2d 54 20 20 20 20 20 20 31 2e 30 20 03 52 00 19 |-T 1.0 .R..|
> 00000040 00 1a 00 00 53 4b 32 33 30 31 31 31 30 30 30 38 |....SK2301110008|
> 00000050 20 20 20 20 32 33 30 31 31 30 20 20 68 f0 01 e8 | 230110 h...|
> 00000060 00 00 11 37 4f 7a dc ff 3d c0 6e 74 9b 7c 06 ca |...7Oz..=.nt.|..|
> 00000070 e1 d0 f9 00 00 00 00 00 00 00 00 00 08 f0 fc 64 |...............d|
> 00000080 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
> *
> 00000100 5f 00 ce 00 5a 00 d3 00 8c a0 75 30 88 b8 79 18 |_...Z.....u0..y.|
> 00000110 1d 4c 01 f4 19 64 03 e8 4d f0 06 30 3d e8 06 f2 |.L...d..M..0=...|
> 00000120 2b d4 00 c7 27 10 00 df 00 00 00 00 00 00 00 00 |+...'...........|
> 00000130 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
> 00000140 00 00 00 00 3f 80 00 00 00 00 00 00 01 00 00 00 |....?...........|
> 00000150 01 00 00 00 01 00 00 00 01 00 00 00 00 00 00 f1 |................|
> 00000160 29 1a 82 41 0b b8 13 88 0f a0 ff ff ff ff 80 ff |)..A............|
> 00000170 00 00 ff ff 00 00 ff ff 04 ff ff ff ff ff ff 00 |................|
> 00000180 43 4e 53 38 54 55 54 41 41 43 33 30 2d 31 34 31 |CNS8TUTAAC30-141|
> 00000190 30 2d 30 34 56 30 34 20 49 fb 46 00 00 00 00 29 |0-04V04 I.F....)|
> 000001a0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
> 000001b0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 aa aa |................|
> 000001c0 47 4c 43 2d 54 20 20 20 20 20 20 20 20 20 20 20 |GLC-T |
> 000001d0 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 97 | .|
> 000001e0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
> 000001f0 00 00 00 00 00 00 00 00 00 40 00 40 00 00 00 00 |......... at .@....|
>
> how can we add a quirk to support this?
Why does it need a quirk?
>
> some more information:
>
> root at bpi-r3:~# ethtool eth1
> Settings for eth1:
> Supported ports: [ FIBRE ]
> Supported link modes: 2500baseX/Full
> Supported pause frame use: Symmetric Receive-only
> Supports auto-negotiation: Yes
> Supported FEC modes: Not reported
> Advertised link modes: 2500baseX/Full
> Advertised pause frame use: Symmetric Receive-only
> Advertised auto-negotiation: Yes
> Advertised FEC modes: Not reported
> Speed: 2500Mb/s
> Duplex: Full
> Auto-negotiation: on
> Port: FIBRE
> PHYAD: 0
> Transceiver: internal
> Current message level: 0x000000ff (255)
> drv probe link timer ifdown ifup rx_err tx_err
> Link detected: yes
> root at bpi-r3:~# ethtool -m eth1
> Identifier : 0x03 (SFP)
> Extended identifier : 0x04 (GBIC/SFP defined by 2-wire interface ID)
> Connector : 0x07 (LC)
> Transceiver codes : 0x00 0x01 0x00 0x00 0x00 0x00 0x02 0x00 0x00
> Transceiver type : SONET: OC-48, short reach
> Encoding : 0x05 (SONET Scrambled)
> BR, Nominal : 2500MBd
> Rate identifier : 0x00 (unspecified)
> Length (SMF,km) : 0km
> Length (SMF) : 0m
> Length (50um) : 300m
> Length (62.5um) : 200m
> Length (Copper) : 0m
> Length (OM3) : 0m
> Laser wavelength : 850nm
> Vendor name : OEM
> Vendor OUI : 00:00:00
> Vendor PN : SFP-2.5G-T
> Vendor rev : 1.0
> Option values : 0x00 0x1a
> Option : RX_LOS implemented
> Option : TX_FAULT implemented
> Option : TX_DISABLE implemented
> BR margin, max : 0%
> BR margin, min : 0%
> Vendor SN : SK2301110008
> Date code : 230110
> Optical diagnostics support : Yes
> Laser bias current : 6.000 mA
> Laser output power : 0.5000 mW / -3.01 dBm
> Receiver signal average optical power : 0.4000 mW / -3.98 dBm
> Module temperature : 28.21 degrees C / 82.78 degrees F
> Module voltage : 3.3067 V
> Alarm/warning flags implemented : Yes
> Laser bias current high alarm : Off
> Laser bias current low alarm : Off
> Laser bias current high warning : Off
> Laser bias current low warning : Off
> Laser output power high alarm : Off
> Laser output power low alarm : Off
> Laser output power high warning : Off
> Laser output power low warning : Off
> Module temperature high alarm : Off
> Module temperature low alarm : Off
> Module temperature high warning : Off
> Module temperature low warning : Off
> Module voltage high alarm : Off
> Module voltage low alarm : Off
> Module voltage high warning : Off
> Module voltage low warning : Off
> Laser rx power high alarm : Off
> Laser rx power low alarm : Off
> Laser rx power high warning : Off
> Laser rx power low warning : Off
> Laser bias current high alarm threshold : 15.000 mA
> Laser bias current low alarm threshold : 1.000 mA
> Laser bias current high warning threshold : 13.000 mA
> Laser bias current low warning threshold : 2.000 mA
> Laser output power high alarm threshold : 1.9952 mW / 3.00 dBm
> Laser output power low alarm threshold : 0.1584 mW / -8.00 dBm
> Laser output power high warning threshold : 1.5848 mW / 2.00 dBm
> Laser output power low warning threshold : 0.1778 mW / -7.50 dBm
> Module temperature high alarm threshold : 95.00 degrees C / 203.00 degrees F
> Module temperature low alarm threshold : -50.00 degrees C / -58.00 degrees F
> Module temperature high warning threshold : 90.00 degrees C / 194.00 degrees F
> Module temperature low warning threshold : -45.00 degrees C / -49.00 degrees F
> Module voltage high alarm threshold : 3.6000 V
> Module voltage low alarm threshold : 3.0000 V
> Module voltage high warning threshold : 3.5000 V
> Module voltage low warning threshold : 3.1000 V
> Laser rx power high alarm threshold : 1.1220 mW / 0.50 dBm
> Laser rx power low alarm threshold : 0.0199 mW / -17.01 dBm
> Laser rx power high warning threshold : 1.0000 mW / 0.00 dBm
> Laser rx power low warning threshold : 0.0223 mW / -16.52 dBm
>
> i guess this sfp have a phy as it can operate in 100/1000/2500 mode like described on the module.
It would help to know the kernel messages.
Thanks.
--
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last!
More information about the Linux-mediatek
mailing list