Aw: Re: Re: [PATCH v3 0/5] arm: dts: mt7623: relocate gmacs, mt7530 switch, and add port at 5

Frank Wunderlich frank-w at public-files.de
Sat Feb 18 04:18:25 PST 2023


Hi,

> Gesendet: Samstag, 18. Februar 2023 um 11:49 Uhr
> Von: "Arınç ÜNAL" <arinc.unal at arinc9.com>
> An: "Frank Wunderlich" <frank-w at public-files.de>

> On 18.02.2023 13:24, Frank Wunderlich wrote:
> > Hi,
> > 
> > finally get some time to bootup with this series on my r2.
> > 
> > I see that inserting the port at 5 as cpu-port maps this as default-cpu because dsa-core uses first found cpu-port as
> > default (dsa_tree_setup_cpu_ports in dsa.c) and because of lower bandwidth (rgmii instead of trgmii) not the best choice.
> > 
> > But it look worse...network is currently broken (set both gmacs up).
> > I see arp-packets reaching remote side, but reponse is not received by r2
> > 
> > I have tested it on 6.2-rc8 (wan-port), maybe additional patches are needed?...userspace setup should be right.
> > 
> > so i added series on top of net-next (no additional patches except some basic like build-script,defconfig and such)...same result...
> > 
> > i'm not sure if i change the mapping from userspace back to eth0, so disabled port at 5 in switch, now port6 is
> > cpu-port again and it works...so something is wrong with port5 of switch or gmac1.
> 
> That's a driver issue and will be fixed once an accepted version of 
> these patches [0] [1] [2] are applied to net-next. You should have them 
> on your inbox, I specifically told Richard to CC you.

yes, i've got them, but not applied when starting these tests. Not thought, that this change is necessary 
as we use both gmac on mt7531/bpi-r3 with out problems.

with these 3 Patches network-connection works, but only at ~624 Mbit/s in TX-Mode (started iperf3-client on r2 without -R) and massive retransmitts on first run, other direction is clean.

and these Patches need to be applied first (when fixed up) else network is broken.

> This is devicetree bindings. We're here to describe the hardware. The 
> way a driver works should not affect describing the hardware.

thats right, but it should not break/change behaviour like now all ports have only ~600Mbit because of
moving them all to the other gmac which has obvious issues.

> To address the lower bandwidth situation you mentioned, a devicetree 
> property to designate a CPU port as the default CPU port could be 
> introduced. I'm not aware of a similar conversation so I'll send a mail 
> to netdev to discuss this. Will CC you.

isn't there a way to leave ports by default on the the better gmac (gmac0=trgmii)?
maybe moving port5 below port6...not nice, but then port6 is the first cpu found.
or maybe defined the default cpu in driver which gets picked up by core (define port6 if available as default).
Imho additional dts-propperty is wrong approch...it should be handled by driver. But cpu-port-selection is 
currently done in dsa-core which makes it a bit difficult.

I'm not sure how the multi-cpu support in dsa-core ended and how you use the other gmac not used by dsa-core

set master in userspace-config? i remember you've sent a patch adding callback for it.

imho dts change should be applied if these points are cleared...

regards Frank



More information about the Linux-mediatek mailing list