[PATCH net-next v2 5/5] net: mediatek: sgmii: refactor power cycling into mtk_pcs_config()

[Alexander Couzens]

Both code paths (autonegotiated and force mode) are power cycling
the phy. Move power cycling code to the caller to remove code
duplicity.

Signed-off-by: Alexander Couzens <lynxis at fe80.eu>
---
 drivers/net/ethernet/mediatek/mtk_sgmii.c | 45 ++++++++---------------
 1 file changed, 15 insertions(+), 30 deletions(-)

diff --git a/drivers/net/ethernet/mediatek/mtk_sgmii.c b/drivers/net/ethernet/mediatek/mtk_sgmii.c
index 4c8e8c7b1d32..50f605208295 100644
--- a/drivers/net/ethernet/mediatek/mtk_sgmii.c
+++ b/drivers/net/ethernet/mediatek/mtk_sgmii.c
@@ -25,9 +25,6 @@ static int mtk_pcs_setup_mode_an(struct mtk_pcs *mpcs, phy_interface_t interface
 {
 	unsigned int val;
 
-	/* PHYA power down */
-	regmap_write(mpcs->regmap, SGMSYS_QPHY_PWR_STATE_CTRL, SGMII_PHYA_PWD);
-
 	/* Set SGMII phy speed */
 	regmap_read(mpcs->regmap, mpcs->ana_rgc3, &val);
 	val &= ~RG_PHY_SPEED_MASK;
@@ -48,18 +45,6 @@ static int mtk_pcs_setup_mode_an(struct mtk_pcs *mpcs, phy_interface_t interface
 	val |= SGMII_AN_RESTART | SGMII_AN_ENABLE;
 	regmap_write(mpcs->regmap, SGMSYS_PCS_CONTROL_1, val);
 
-	/* Release PHYA power down state
-	 * Only removing bit SGMII_PHYA_PWD isn't enough.
-	 * There are cases when the SGMII_PHYA_PWD register contains 0x9 which
-	 * prevents SGMII from working. The SGMII still shows link but no traffic
-	 * can flow. Writing 0x0 to the PHYA_PWD register fix the issue. 0x0 was
-	 * taken from a good working state of the SGMII interface.
-	 * Unknown how much the QPHY needs but it is racy without a sleep.
-	 * Tested on mt7622 & mt7986.
-	 */
-	usleep_range(50, 100);
-	regmap_write(mpcs->regmap, SGMSYS_QPHY_PWR_STATE_CTRL, 0);
-
 	return 0;
 
 }
@@ -72,9 +57,6 @@ static int mtk_pcs_setup_mode_force(struct mtk_pcs *mpcs,
 {
 	unsigned int val;
 
-	/* PHYA power down */
-	regmap_write(mpcs->regmap, SGMSYS_QPHY_PWR_STATE_CTRL, SGMII_PHYA_PWD);
-
 	regmap_read(mpcs->regmap, mpcs->ana_rgc3, &val);
 	val &= ~RG_PHY_SPEED_MASK;
 	if (interface == PHY_INTERFACE_MODE_2500BASEX)
@@ -92,18 +74,6 @@ static int mtk_pcs_setup_mode_force(struct mtk_pcs *mpcs,
 	val |= SGMII_SPEED_1000;
 	regmap_write(mpcs->regmap, SGMSYS_SGMII_MODE, val);
 
-	/* Release PHYA power down state
-	 * Only removing bit SGMII_PHYA_PWD isn't enough.
-	 * There are cases when the SGMII_PHYA_PWD register contains 0x9 which
-	 * prevents SGMII from working. The SGMII still shows link but no traffic
-	 * can flow. Writing 0x0 to the PHYA_PWD register fix the issue. 0x0 was
-	 * taken from a good working state of the SGMII interface.
-	 * Unknown how much the QPHY needs but it is racy without a sleep.
-	 * Tested on mt7622 & mt7986.
-	 */
-	usleep_range(50, 100);
-	regmap_write(mpcs->regmap, SGMSYS_QPHY_PWR_STATE_CTRL, 0);
-
 	return 0;
 }
 
@@ -115,12 +85,27 @@ static int mtk_pcs_config(struct phylink_pcs *pcs, unsigned int mode,
 	struct mtk_pcs *mpcs = pcs_to_mtk_pcs(pcs);
 	int err = 0;
 
+	/* PHYA power down */
+	regmap_write(mpcs->regmap, SGMSYS_QPHY_PWR_STATE_CTRL, SGMII_PHYA_PWD);
+
 	/* Setup SGMIISYS with the determined property */
 	if (interface != PHY_INTERFACE_MODE_SGMII)
 		err = mtk_pcs_setup_mode_force(mpcs, interface);
 	else if (phylink_autoneg_inband(mode))
 		err = mtk_pcs_setup_mode_an(mpcs, interface);
 
+	/* Release PHYA power down state
+	 * Only removing bit SGMII_PHYA_PWD isn't enough.
+	 * There are cases when the SGMII_PHYA_PWD register contains 0x9 which
+	 * prevents SGMII from working. The SGMII still shows link but no traffic
+	 * can flow. Writing 0x0 to the PHYA_PWD register fix the issue. 0x0 was
+	 * taken from a good working state of the SGMII interface.
+	 * Unknown how much the QPHY needs but it is racy without a sleep.
+	 * Tested on mt7622 & mt7986.
+	 */
+	usleep_range(50, 100);
+	regmap_write(mpcs->regmap, SGMSYS_QPHY_PWR_STATE_CTRL, 0);
+
 	return err;
 }
 
-- 
2.37.3