[PATCH 11/14] dt-bindings: pinctrl: add binding for Ralink MT7620 pinctrl

[Krzysztof Kozlowski]

On 13/04/2022 08:07, Arınç ÜNAL wrote:
> Add binding for the Ralink MT7620 pin controller for MT7620, MT7628 and
> MT7688 SoCs.
> 
> Signed-off-by: Arınç ÜNAL <arinc.unal at arinc9.com>
> ---
>  .../pinctrl/ralink,mt7620-pinctrl.yaml        | 87 +++++++++++++++++++
>  1 file changed, 87 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/pinctrl/ralink,mt7620-pinctrl.yaml
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/ralink,mt7620-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/ralink,mt7620-pinctrl.yaml
> new file mode 100644
> index 000000000000..01578b8aa277
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/ralink,mt7620-pinctrl.yaml
> @@ -0,0 +1,87 @@
> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pinctrl/ralink,mt7620-pinctrl.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Ralink MT7620 Pin Controller
> +
> +maintainers:
> +  - Arınç ÜNAL <arinc.unal at arinc9.com>
> +  - Sergio Paracuellos <sergio.paracuellos at gmail.com>
> +
> +description:
> +  Ralink MT7620 pin controller for MT7620, MT7628 and MT7688 SoCs.
> +  The pin controller can only set the muxing of pin groups. Muxing indiviual pins

Run spellcheck on original bindings, don't copy same typos.

> +  is not supported. There is no pinconf support.
> +
> +properties:
> +  compatible:
> +    const: ralink,mt7620-pinctrl
> +
> +patternProperties:
> +  '-pins$':
> +    type: object
> +    patternProperties:
> +      '^(.*-)?pinmux$':

Why do you have two levels here? pins->pinmux->actual pin configuration?
Cannot be something like brcm,bcm636x has?

> +        type: object
> +        description: node for pinctrl.
> +        $ref: pinmux-node.yaml#
> +
> +        properties:
> +          groups:
> +            description: The pin group to select.

I wonder where do you configure particular pins because these are
groups... It's a bit confusing to configure "i2c" group into "i2c" -
looks obvious.

> +            enum: [
> +              # For MT7620 SoC
> +              ephy, i2c, mdio, nd_sd, pa, pcie, rgmii1, rgmii2, spi, spi refclk, uartf, uartlite, wdt, wled,
> +
> +              # For MT7628 and MT7688 SoCs
> +              gpio, i2c, i2s, p0led_an, p0led_kn, p1led_an, p1led_kn, p2led_an, p2led_kn, p3led_an,
> +              p3led_kn, p4led_an, p4led_kn, perst, pwm0, pwm1, refclk, sdmode, spi, spi cs1, spis, uart0,
> +              uart1, uart2, wdt, wled_an, wled_kn,
> +            ]
> +
> +          function:
> +            description: The mux function to select.
> +            enum: [
> +              # For MT7620 SoC
> +              ephy, gpio, gpio i2s, gpio uartf, i2c, i2s uartf, mdio, nand, pa, pcie refclk, pcie rst,
> +              pcm gpio, pcm i2s, pcm uartf, refclk, rgmii1, rgmii2, sd, spi, spi refclk, uartf, uartlite,
> +              wdt refclk, wdt rst, wled,
> +
> +              # For MT7628 and MT7688 SoCs
> +              antenna, debug, gpio, i2c, i2s, jtag, p0led_an, p0led_kn, p1led_an, p1led_kn, p2led_an,
> +              p2led_kn, p3led_an, p3led_kn, p4led_an, p4led_kn, pcie, pcm, perst, pwm, pwm0, pwm1,
> +              pwm_uart2, refclk, rsvd, sdxc, sdxc d5 d4, sdxc d6, sdxc d7, spi, spi cs1, spis, sw_r, uart0,
> +              uart1, uart2, utif, wdt, wled_an, wled_kn, -,

All these lines do not fit in 80-character limit. Linux coding style
still expects this in most of cases.

> +            ]
> +

Best regards,
Krzysztof