[PATCH v1 3/5] arm64: dts: mt8195: add gce node

[Chun-Kuang Hu]

Hi, Jason:

jason-jh.lin <jason-jh.lin at mediatek.com> 於 2021年6月30日 週三 下午1:18寫道：
>
> add gce node on dts file.
>
> Change-Id: I805455cb7c645cb5a24ce1c87fe891a807069123
> Signed-off-by: jason-jh.lin <jason-jh.lin at mediatek.com>
> ---
> This patch is based on [1]
> [1] Add Mediatek SoC MT8195 and evaluation board dts and Makefile
>     - https://patchwork.kernel.org/project/linux-mediatek/patch/20210601075350.31515-2-seiya.wang@mediatek.com/
> ---
>  arch/arm64/boot/dts/mediatek/mt8195.dtsi | 21 +++++++++++++++++++++
>  1 file changed, 21 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/mediatek/mt8195.dtsi b/arch/arm64/boot/dts/mediatek/mt8195.dtsi
> index c146a91c6272..38054196eea4 100644
> --- a/arch/arm64/boot/dts/mediatek/mt8195.dtsi
> +++ b/arch/arm64/boot/dts/mediatek/mt8195.dtsi
> @@ -6,6 +6,7 @@
>
>  /dts-v1/;
>  #include <dt-bindings/clock/mt8195-clk.h>
> +#include <dt-bindings/gce/mt8195-gce.h>
>  #include <dt-bindings/interrupt-controller/arm-gic.h>
>  #include <dt-bindings/interrupt-controller/irq.h>
>  #include <dt-bindings/power/mt8195-power.h>
> @@ -717,6 +718,26 @@
>                         #clock-cells = <1>;
>                 };
>
> +               gce0: mdp_mailbox at 10320000 {
> +                       compatible = "mediatek,mt8195-gce";
> +                       reg = <0 0x10320000 0 0x4000>;
> +                       interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH 0>;
> +                       #mbox-cells = <3>;
> +                       clocks = <&infracfg_ao CLK_INFRA_AO_GCE>,
> +                                <&infracfg_ao CLK_INFRA_AO_GCE2>;
> +                       clock-names = "gce", "gce1";
> +               };
> +
> +               gce1: disp_mailbox at 10330000 {
> +                       compatible = "mediatek,mt8195-gce";
> +                       reg = <0 0x10330000 0 0x4000>;
> +                       interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH 0>;
> +                       #mbox-cells = <3>;
> +                       clocks = <&infracfg_ao CLK_INFRA_AO_GCE>,
> +                                <&infracfg_ao CLK_INFRA_AO_GCE2>;
> +                       clock-names = "gce", "gce1";

I think each gce could be broken into two function block, the core
function block and event processing block.
Each block has independent clock source and "gce" is for core function
block and "gce1" is for event processing block, is it?
If so, the core function of gce0 and gce1 has common clock source
(<&infracfg_ao CLK_INFRA_AO_GCE>), right?

Regards,
Chun-Kuang.

> +               };
> +
>                 uart0: serial at 11001100 {
>                         compatible = "mediatek,mt8195-uart", "mediatek,mt6577-uart";
>                         reg = <0 0x11001100 0 0x100>;
> --
> 2.18.0
>