[RFC v4 05/11] dt-bindings: drm/mediatek: Add Mediatek HDMI dts binding
Rob Herring
robh+dt at kernel.org
Fri Oct 23 05:29:42 PDT 2015
On Fri, Oct 16, 2015 at 3:12 PM, Philipp Zabel <p.zabel at pengutronix.de> wrote:
> Add the device tree binding documentation for Mediatek HDMI,
> HDMI PHY and HDMI DDC devices.
>
> Signed-off-by: Philipp Zabel <p.zabel at pengutronix.de>
> ---
> Changes since v3:
> - Split CEC block into a separate node, move the hotplug interrupt there
> - Removed reg-names, hdmi now only as a single register range
> - Added mediatek,cec and mediatek,syscon-hdmi phandles
> - Shortened clock names, removed div and sel clocks from the binding
> - Added a pll_ref clock input to the hdmi phy.
> - Fixed the hdmi interrupt to the documented value.
> ---
> .../bindings/drm/mediatek/mediatek,hdmi.txt | 127 +++++++++++++++++++++
> 1 file changed, 127 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/drm/mediatek/mediatek,hdmi.txt
>
> diff --git a/Documentation/devicetree/bindings/drm/mediatek/mediatek,hdmi.txt b/Documentation/devicetree/bindings/drm/mediatek/mediatek,hdmi.txt
> new file mode 100644
> index 0000000..2ba5f65
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/drm/mediatek/mediatek,hdmi.txt
> @@ -0,0 +1,127 @@
> +Mediatek HDMI Encoder
> +=====================
> +
> +The Mediatek HDMI encoder can generate HDMI 1.4a or MHL 2.0 signals from
> +its parallel input.
How do you know whether it is HDMI or MHL on a given board? You should
have a connector node perhaps.
> +
> +Required properties:
> +- compatible: Should be "mediatek,<chip>-hdmi".
> +- reg: Physical base address and length of the controller's registers
> +- interrupts: The interrupt signal from the function block.
> +- clocks: device clocks
> + See Documentation/devicetree/bindings/clock/clock-bindings.txt for details.
> +- clock-names: must contain "pixel", "pll", "bclk", and "spdif".
> +- mediatek,cec: phandle link to the HDMI CEC node.
Do you have more than 1 CEC block? If not, just find the compatible
node with of_find_compatible_node.
> +- ddc-i2c-bus: phandle link to the I2C controller used for DDC EDID probing
This really should be part of a connector node as I2C bus goes to the
connector, not the HDMI block.
> +- phys: phandle link to the HDMI PHY node.
> + See Documentation/devicetree/bindings/phy/phy-bindings.txt for details.
> +- phy-names: must contain "hdmi"
> +- mediatek,syscon-hdmi: phandle link and register offset to the system
> + configuration registers. For mt8173 this must be offset 0x900 into the
> + MMSYS_CONFIG region: <&mmsys 0x900>.
> +- ports: A node containing input and output port nodes with endpoint
> + definitions as documented in Documentation/devicetree/bindings/graph.txt.
> +- port at 0: The input port in the ports node should be connected to a DPI output
> + port.
> +
> +Optional properties:
> +- port at 1: The output port in the ports node can be connected to the input port
> + of an attached bridge chip, such as a SlimPort transmitter.
> +
> +HDMI CEC
> +========
> +
> +The HDMI CEC controller handles hotplug detection and CEC communication.
> +
> +Required properties:
> +- compatible: Should be "mediatek,<chip>-cec"
> +- reg: Physical base address and length of the controller's registers
> +- interrupts: The interrupt signal from the function block.
> +- clocks: device clock
> +
> +HDMI DDC
> +========
> +
> +The HDMI DDC i2c controller is used to interface with the HDMI DDC pins.
> +The Mediatek's I2C controller is used to interface with I2C devices.
> +
> +Required properties:
> +- compatible: Should be "mediatek,<chip>-hdmi-ddc"
> +- reg: Physical base address and length of the controller's registers
> +- clocks: device clock
> +- clock-names: Should be "ddc-i2c".
> +
> +HDMI PHY
> +========
> +
> +The HDMI PHY serializes the HDMI encoder's three channel 10-bit parallel
> +output and drives the HDMI pads.
> +
> +Required properties:
> +- compatible: "mediatek,<chip>-hdmi-phy"
> +- reg: Physical base address and length of the module's registers
> +- clocks: PLL reference clock
> +- clock-names: must contain "pll_ref"
> +- #phy-cells: must be <0>.
> +
> +Optional properties:
> +- ibias: TX DRV bias current for <1.65Gbps, defaults to 0xa
> +- ibias_up: TX DRV bias current for >1.65Gbps, defaults to 0x1c
prefix with "mediatek,"
> +
> +Example:
> +
> +cec: cec at 10013000 {
> + compatible = "mediatek,mt8173-cec";
> + reg = <0 0x10013000 0 0xbc>;
> + interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_LOW>;
> + clocks = <&infracfg CLK_INFRA_CEC>;
> +};
> +
> +hdmi_phy: hdmi-phy at 10209100 {
> + compatible = "mediatek,mt8173-hdmi-phy";
> + reg = <0 0x10209100 0 0x24>;
> + clocks = <&apmixedsys CLK_APMIXED_HDMI_REF>;
> + clock-names = "pll_ref";
> + ibias = <0xa>;
> + ibias_up = <0x1c>;
> + #phy-cells = <0>;
> +};
> +
> +hdmi_ddc0: i2c at 11012000 {
> + compatible = "mediatek,mt8173-hdmi-ddc";
> + reg = <0 0x11012000 0 0x1c>;
> + interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_LOW>;
> + clocks = <&pericfg CLK_PERI_I2C5>;
> + clock-names = "ddc-i2c";
> +};
> +
> +hdmi0: hdmi at 14025000 {
> + compatible = "mediatek,mt8173-hdmi";
> + reg = <0 0x14025000 0 0x400>;
> + interrupts = <GIC_SPI 206 IRQ_TYPE_LEVEL_LOW>;
> + clocks = <&mmsys CLK_MM_HDMI_PIXEL>,
> + <&mmsys CLK_MM_HDMI_PLLCK>,
> + <&mmsys CLK_MM_HDMI_AUDIO>,
> + <&mmsys CLK_MM_HDMI_SPDIF>;
> + clock-names = "pixel", "pll", "bclk", "spdif";
> + mediatek,cec = <&cec>;
> + ddc-i2c-bus = <&hdmiddc0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&hdmi_pin>;
> + phys = <&hdmi_phy>;
> + phy-names = "hdmi";
> + mediatek,syscon-hdmi = <&mmsys 0x900>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port at 0 {
> + reg = <0>;
> +
> + hdmi0_in: endpoint {
> + remote-endpoint = <&dpi0_out>;
> + };
> + };
> + };
> +};
> --
> 2.6.1
>
More information about the Linux-mediatek
mailing list