[PATCH v26 06/10] power: reset: Add psci-reboot-mode driver

[Bartosz Golaszewski]

On Mon, 28 Sep 2026 08:09:18 +0200, Shivendra Pratap
<shivendra.pratap at oss.qualcomm.com> said:
> PSCI supports different types of resets like SYSTEM_RESET, SYSTEM_RESET2
> ARCH WARM reset and SYSTEM_RESET2 vendor-specific resets. Currently
> there is no common driver that handles all supported psci resets at one
> place. Additionally, there is no common mechanism to issue the supported
> psci resets from userspace.
>
> Add psci-reboot-mode as an auxiliary device created by the psci-devices
> driver. Define two types of PSCI resets, predefined-resets and
> vendor-specific resets. Predefined-resets are defined by psci driver
> and vendor-specific resets are defined by SoC vendors, under the
> psci:reboot-mode node of SoC device tree.
>
> Register the driver with the reboot-mode framework to interface these
> resets to userspace. When userspace initiates a supported command, pass
> the reset arguments to the PSCI driver to enable command-based reset.
>
> This change allows userspace to issue supported PSCI reset commands
> using the standard reboot system calls while enabling SoC vendors to
> define their specific resets for PSCI.
>
> Suggested-by: Ulf Hansson <ulf.hansson at oss.qualcomm.com>
> Suggested-by: Lee Jones <lee at kernel.org>
> Suggested-by: Bartosz Golaszewski <bartosz.golaszewski at oss.qualcomm.com>
> Signed-off-by: Shivendra Pratap <shivendra.pratap at oss.qualcomm.com>
> ---
>  MAINTAINERS                            |   1 +
>  drivers/firmware/psci/psci-devices.c   |   4 ++
>  drivers/power/reset/Kconfig            |  11 ++++
>  drivers/power/reset/Makefile           |   1 +
>  drivers/power/reset/psci-reboot-mode.c | 104 +++++++++++++++++++++++++++++++++
>  5 files changed, 121 insertions(+)
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 70a11f2ff61d..1007d5cd2e13 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -22058,6 +22058,7 @@ L:	linux-arm-kernel at lists.infradead.org (moderated for non-subscribers)
>  S:	Maintained
>  F:	Documentation/devicetree/bindings/arm/psci.yaml
>  F:	drivers/firmware/psci/
> +F:	drivers/power/reset/psci-reboot-mode.c
>  F:	include/linux/psci.h
>  F:	include/uapi/linux/psci.h
>
> diff --git a/drivers/firmware/psci/psci-devices.c b/drivers/firmware/psci/psci-devices.c
> index d23befc490ed..04f24b8d9943 100644
> --- a/drivers/firmware/psci/psci-devices.c
> +++ b/drivers/firmware/psci/psci-devices.c
> @@ -20,6 +20,10 @@ static const struct arm_psci_device_info arm_psci_devices[] = {
>  	{
>  		.name = "psci-cpuidle-domain",
>  	},
> +	{
> +		.name = "psci-reboot-mode",
> +		.of_node_name = "reboot-mode",
> +	},
>  };
>
>  static void arm_psci_auxiliary_device_release(struct device *dev)
> diff --git a/drivers/power/reset/Kconfig b/drivers/power/reset/Kconfig
> index bce996bbef28..f165a41d40ed 100644
> --- a/drivers/power/reset/Kconfig
> +++ b/drivers/power/reset/Kconfig
> @@ -360,6 +360,17 @@ config NVMEM_REBOOT_MODE
>  	  then the bootloader can read it and take different
>  	  action according to the mode.
>
> +config PSCI_REBOOT_MODE
> +	bool "PSCI reboot mode driver"
> +	depends on ARM_PSCI_DEVICES
> +	select AUXILIARY_BUS
> +	select REBOOT_MODE
> +	help
> +	  Say y here to enable the PSCI reboot mode driver. The driver
> +	  registers with the reboot-mode framework to configure PSCI
> +	  reset commands, which are executed by the PSCI driver during
> +	  psci_sys_reset().
> +
>  config POWER_MLXBF
>  	tristate "Mellanox BlueField power handling driver"
>  	depends on (GPIO_MLXBF2 || GPIO_MLXBF3) && ACPI
> diff --git a/drivers/power/reset/Makefile b/drivers/power/reset/Makefile
> index e31cab4ba78e..45d8aaaffaa1 100644
> --- a/drivers/power/reset/Makefile
> +++ b/drivers/power/reset/Makefile
> @@ -41,5 +41,6 @@ obj-$(CONFIG_REBOOT_MODE) += reboot-mode.o
>  obj-$(CONFIG_SYSCON_REBOOT_MODE) += syscon-reboot-mode.o
>  obj-$(CONFIG_POWER_RESET_SC27XX) += sc27xx-poweroff.o
>  obj-$(CONFIG_NVMEM_REBOOT_MODE) += nvmem-reboot-mode.o
> +obj-$(CONFIG_PSCI_REBOOT_MODE) += psci-reboot-mode.o
>  obj-$(CONFIG_POWER_MLXBF) += pwr-mlxbf.o
>  obj-$(CONFIG_POWER_RESET_QEMU_VIRT_CTRL) += qemu-virt-ctrl.o
> diff --git a/drivers/power/reset/psci-reboot-mode.c b/drivers/power/reset/psci-reboot-mode.c
> new file mode 100644
> index 000000000000..bf2dd6626feb
> --- /dev/null
> +++ b/drivers/power/reset/psci-reboot-mode.c
> @@ -0,0 +1,104 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
> + */
> +
> +#include <linux/array_size.h>
> +#include <linux/auxiliary_bus.h>
> +#include <linux/device.h>
> +#include <linux/errno.h>
> +#include <linux/init.h>
> +#include <linux/kconfig.h>

Huh?

With that removed:

Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski at oss.qualcomm.com>