[PATCH 2/3] arm64: dts: freescale: add Aquila iMX95 support

[Frank Li]

On Wed, May 06, 2026 at 03:01:56PM +0200, Franz Schnyder wrote:
> From: João Paulo Gonçalves <joao.goncalves at toradex.com>
>
> Add support for the Toradex Aquila iMX95 and its development carrier
> board.
>
> The module consists of an NXP i.MX95 family SoC, up to 16GB LPDDR5 RAM,
> up to 128GB of storage, a USB 3.2 OTG and USB 2.0 Host, a Gigabit
> Ethernet PHY, a 10 Gigabit Ethernet interface, an I2C EEPROM and
> Temperature Sensor, an RX8130 RTC, one Quad lane CSI interface, one Quad
> lane DSI or CSI interface, one LVDS interface (one or two channels), and
> some optional addons: DisplayPort (through a DSI-DP bridge), TPM 2.0,
> and a WiFi/BT module.
>
...
> +
> +&scmi_iomuxc {
> +	/* Aquila ETH_2_XGMII_MDIO */
> +	pinctrl_emdio: emdiogrp {
> +		fsl,pins = <IMX95_PAD_ENET2_MDC__NETCMIX_TOP_NETC_MDC	0x57e>, /* Aquila B90 */
> +			   <IMX95_PAD_ENET2_MDIO__NETCMIX_TOP_NETC_MDIO	0x97e>; /* Aquila B89 */
> +	};
> +
> +	/* Aquila ETH_1 */
> +	pinctrl_enetc0: enetc0grp {
> +		fsl,pins = <IMX95_PAD_ENET1_TX_CTL__NETCMIX_TOP_ETH0_RGMII_TX_CTL	0x57e>, /* ENET1_TX_CTL */
> +			   <IMX95_PAD_ENET1_TXC__NETCMIX_TOP_ETH0_RGMII_TX_CLK		0x58e>, /* ENET1_TXC    */
> +			   <IMX95_PAD_ENET1_TD0__NETCMIX_TOP_ETH0_RGMII_TD0		0x50e>, /* ENET1_TDO    */
> +			   <IMX95_PAD_ENET1_TD1__NETCMIX_TOP_ETH0_RGMII_TD1		0x50e>, /* ENET1_TD1    */
> +			   <IMX95_PAD_ENET1_TD2__NETCMIX_TOP_ETH0_RGMII_TD2		0x50e>, /* ENET1_TD2    */
> +			   <IMX95_PAD_ENET1_TD3__NETCMIX_TOP_ETH0_RGMII_TD3		0x50e>, /* ENET1_TD3    */
> +			   <IMX95_PAD_ENET1_RX_CTL__NETCMIX_TOP_ETH0_RGMII_RX_CTL	0x57e>, /* ENET1_RX_CTL */
> +			   <IMX95_PAD_ENET1_RXC__NETCMIX_TOP_ETH0_RGMII_RX_CLK		0x58e>, /* ENET1_RXC    */
> +			   <IMX95_PAD_ENET1_RD0__NETCMIX_TOP_ETH0_RGMII_RD0		0x57e>, /* ENET1_RD0    */
> +			   <IMX95_PAD_ENET1_RD1__NETCMIX_TOP_ETH0_RGMII_RD1		0x57e>, /* ENET1_RD1    */
> +			   <IMX95_PAD_ENET1_RD2__NETCMIX_TOP_ETH0_RGMII_RD2		0x57e>, /* ENET1_RD2    */
> +			   <IMX95_PAD_ENET1_RD3__NETCMIX_TOP_ETH0_RGMII_RD3		0x57e>; /* ENET1_RD3    */
> +	};
> +
> +	pinctrl_ctrl_dp_clk_en: dpclkengrp {
> +		fsl,pins = <IMX95_PAD_SAI1_TXFS__AONMIX_TOP_GPIO1_IO_BIT11	0x11e>; /* CTRL_DP_CLK_EN */
> +	};
> +
> +	pinctrl_ctrl_gpio_exp_int: gpioexpintgrp {
> +		fsl,pins = <IMX95_PAD_SAI1_TXD0__AONMIX_TOP_GPIO1_IO_BIT13	0x31e>; /* CTRL_GPIO_EXP_INT# */
> +	};
> +
> +	/* Aquila CTRL_WAKE1_MICO# */
> +	pinctrl_ctrl_wake1_mico: ctrlwake1micogrp {
> +		fsl,pins = <IMX95_PAD_XSPI1_SS1_B__GPIO5_IO_BIT11	0x31e>; /* Aquila D6 */
> +	};

This list is quite long, need keep alphabet order by node name. To reduce
this kinds problem, suggest run https://github.com/lznuaa/dt-format for
new dts.

Frank