[PATCH 3/3] arm64: dts: freescale: imx95-aquila: Add Clover carrier board
Franz Schnyder
fra.schnyder at gmail.com
Wed May 6 06:01:57 PDT 2026
From: Antoine Gouby <antoine.gouby at toradex.com>
Add support for the Aquila i.MX95 SoM mated with the Clover carrier
board. Clover is a low-cost carrier board for the Aquila family
featuring a small form factor (Nano-ITX 120mm x 120mm) and built for
volume production.
Link: https://www.toradex.com/computer-on-modules/aquila-arm-family/nxp-imx95
Link: https://www.toradex.com/products/carrier-board/clover
Signed-off-by: Antoine Gouby <antoine.gouby at toradex.com>
Signed-off-by: Franz Schnyder <franz.schnyder at toradex.com>
---
arch/arm64/boot/dts/freescale/Makefile | 1 +
.../boot/dts/freescale/imx95-aquila-clover.dts | 294 +++++++++++++++++++++
2 files changed, 295 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 178f55255dc14..55fb5f9f561ee 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -514,6 +514,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx95-15x15-evk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx95-15x15-frdm.dtb
dtb-$(CONFIG_ARCH_MXC) += imx95-19x19-evk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx95-19x19-evk-sof.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx95-aquila-clover.dtb
dtb-$(CONFIG_ARCH_MXC) += imx95-aquila-dev.dtb
dtb-$(CONFIG_ARCH_MXC) += imx95-toradex-smarc-dev.dtb
dtb-$(CONFIG_ARCH_MXC) += imx95-tqma9596sa-mb-smarc-2.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx95-aquila-clover.dts b/arch/arm64/boot/dts/freescale/imx95-aquila-clover.dts
new file mode 100644
index 0000000000000..021d437763412
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx95-aquila-clover.dts
@@ -0,0 +1,294 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) Toradex
+ *
+ * https://www.toradex.com/computer-on-modules/aquila-arm-family/nxp-imx95
+ * https://www.toradex.com/products/carrier-board/clover
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/pwm/pwm.h>
+#include <dt-bindings/usb/pd.h>
+#include "imx95-aquila.dtsi"
+
+/ {
+ model = "Aquila iMX95 on Aquila Clover Board";
+ compatible = "toradex,aquila-imx95-clover",
+ "toradex,aquila-imx95",
+ "fsl,imx95";
+
+ aliases {
+ eeprom1 = &carrier_eeprom;
+ };
+
+ dp_1_connector: dp0-connector {
+ compatible = "dp-connector";
+ dp-pwr-supply = <®_dp_3p3v>;
+ type = "full-size";
+
+ port {
+ dp_1_connector_in: endpoint {
+ remote-endpoint = <&dsi2dp_out>;
+ };
+ };
+ };
+
+ reg_dp_3p3v: regulator-dp-3p3v {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_21_dp>;
+ /* Aquila GPIO_21_DP */
+ gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-name = "DP_3V3";
+ startup-delay-us = <10000>;
+ };
+};
+
+/* Aquila ADC_[1-4] */
+&adc1 {
+ status = "okay";
+};
+
+/* Aquila CTRL_WAKE1_MICO# */
+&aquila_key_wake {
+ status = "okay";
+};
+
+&dsi2dp_out {
+ remote-endpoint = <&dp_1_connector_in>;
+};
+
+/* Aquila ETH_1 */
+&enetc_port0 {
+ status = "okay";
+};
+
+/* Aquila CAN_1 */
+&flexcan1 {
+ status = "okay";
+};
+
+/* Aquila CAN_2 */
+&flexcan2 {
+ status = "okay";
+};
+
+/* Aquila CAN_3 */
+&flexcan3 {
+ status = "okay";
+};
+
+/* Aquila CAN_4 */
+&flexcan4 {
+ status = "okay";
+};
+
+/* Aquila QSPI_1 */
+&flexspi1 {
+ pinctrl-0 = <&pinctrl_flexspi1_4bit>,
+ <&pinctrl_qspi_cs1>;
+
+ status = "okay";
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0x0>;
+ spi-max-frequency = <66000000>;
+ spi-rx-bus-width = <4>;
+ spi-tx-bus-width = <4>;
+ cdns,read-delay = <0>;
+ cdns,tchsh-ns = <3>;
+ cdns,tsd2d-ns = <10>;
+ cdns,tshsl-ns = <30>;
+ cdns,tslch-ns = <8>;
+ };
+};
+
+&gpio4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_1>,
+ <&pinctrl_gpio_2>,
+ <&pinctrl_gpio_3>,
+ <&pinctrl_gpio_4>;
+};
+
+/* Aquila I2C_2 */
+&i3c2 {
+ status = "okay";
+};
+
+/* Aquila I2C_1 */
+&lpi2c2 {
+ status = "okay";
+
+ fan_controller: fan at 18 {
+ compatible = "ti,amc6821";
+ reg = <0x18>;
+ #pwm-cells = <2>;
+
+ fan {
+ cooling-levels = <255>;
+ pwms = <&fan_controller 40000 PWM_POLARITY_INVERTED>;
+ };
+ };
+
+ temperature-sensor at 4f {
+ compatible = "ti,tmp1075";
+ reg = <0x4f>;
+ };
+
+ /* USB-C OTG (TCPC USB PD PHY) */
+ tcpc at 52 {
+ compatible = "nxp,ptn5110", "tcpci";
+ reg = <0x52>;
+ interrupt-parent = <&som_gpio_expander_1>;
+ interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+
+ connector {
+ compatible = "usb-c-connector";
+ data-role = "dual";
+ op-sink-microwatt = <0>;
+ power-role = "dual";
+ self-powered;
+ sink-pdos = <PDO_FIXED(5000, 0, PDO_FIXED_USB_COMM)>;
+ source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+ try-power-role = "sink";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+
+ typec_con_hs: endpoint {
+ remote-endpoint = <&usb1_con_hs>;
+ };
+ };
+
+ port at 1 {
+ reg = <1>;
+
+ typec_con_ss: endpoint {
+ remote-endpoint = <&usb1_con_ss>;
+ };
+ };
+ };
+ };
+ };
+
+ carrier_eeprom: eeprom at 57 {
+ compatible = "st,24c02", "atmel,24c02";
+ reg = <0x57>;
+ pagesize = <16>;
+ };
+};
+
+/* Aquila I2C_6 */
+&lpi2c5 {
+ status = "okay";
+};
+
+/* Aquila SPI_1 */
+&lpspi6 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lpspi6 &pinctrl_gpio_5>;
+ cs-gpios = <&gpio2 0 GPIO_ACTIVE_LOW>, <&gpio4 18 GPIO_ACTIVE_LOW>;
+
+ status = "okay";
+
+ tpm at 1 {
+ compatible = "infineon,slb9670", "tcg,tpm_tis-spi";
+ reg = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_6>;
+ interrupt-parent = <&gpio4>;
+ interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
+ spi-max-frequency = <12000000>;
+ };
+};
+
+/* Aquila UART_3, used as the Linux Console */
+&lpuart1 {
+ status = "okay";
+};
+
+/* Aquila UART_4 */
+&lpuart2 {
+ status = "okay";
+};
+
+/* Aquila UART_1 */
+&lpuart3 {
+ status = "okay";
+};
+
+/* Aquila UART_2 */
+&lpuart7 {
+ status = "okay";
+};
+
+/* Aquila PCIE_1 */
+&pcie0 {
+ status = "okay";
+};
+
+&som_dsi2dp_bridge {
+ status = "okay";
+};
+
+/* Aquila PWM_1 */
+&tpm3 {
+ status = "okay";
+};
+
+/* Aquila PWM_3_DSI and PWM_4_DP */
+&tpm5 {
+ status = "okay";
+};
+
+/* Aquila PWM_2 */
+&tpm6 {
+ status = "okay";
+};
+
+/* Aquila USB_2, optional Bluetooth USB */
+&usb2 {
+ status = "okay";
+};
+
+/* Aquila USB_1 */
+&usb3 {
+ status = "okay";
+};
+
+&usb3_dwc3 {
+ status = "okay";
+
+ port {
+ usb1_con_hs: endpoint {
+ remote-endpoint = <&typec_con_hs>;
+ };
+ };
+};
+
+&usb3_phy {
+ orientation-switch;
+
+ status = "okay";
+
+ port {
+ usb1_con_ss: endpoint {
+ remote-endpoint = <&typec_con_ss>;
+ };
+ };
+};
+
+/* Aquila SD_1 */
+&usdhc2 {
+ status = "okay";
+};
--
2.43.0
More information about the linux-arm-kernel
mailing list