[PATCH 1/2] dt-bindings: phy: nuvoton: Add MA35D1 USB2 OTG PHY binding

[Joey Lu]

Add device tree binding documentation for the Nuvoton MA35D1 USB 2.0
OTG PHY driver (nuvoton,ma35d1-usb2-phy-otg).

PHY index 0 (USB0) is an OTG port whose signals are routed by a hardware
mux to either the DWC2 device controller or the EHCI0/OHCI0 host
controllers depending on the USB ID pin state.  PHY index 1 (USB1) is a
dedicated host-only port.

Optional properties allow board-specific resistor calibration trim
(nuvoton,rcalcode) and over-current detect polarity configuration
(nuvoton,oc-active-high).

Signed-off-by: Joey Lu <a0987203069 at gmail.com>
---
 .../phy/nuvoton,ma35d1-usb2-phy-otg.yaml      | 79 +++++++++++++++++++
 1 file changed, 79 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/nuvoton,ma35d1-usb2-phy-otg.yaml

diff --git a/Documentation/devicetree/bindings/phy/nuvoton,ma35d1-usb2-phy-otg.yaml b/Documentation/devicetree/bindings/phy/nuvoton,ma35d1-usb2-phy-otg.yaml
new file mode 100644
index 000000000000..19f074565cc6
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/nuvoton,ma35d1-usb2-phy-otg.yaml
@@ -0,0 +1,79 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/nuvoton,ma35d1-usb2-phy-otg.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Nuvoton MA35D1 USB 2.0 host PHY
+
+maintainers:
+  - Joey Lu <yclu4 at nuvoton.com>
+
+description:
+  USB 2.0 PHY driver for the Nuvoton MA35D1 SoC, used by the EHCI and
+  OHCI host controllers.
+
+  USB0 (PHY index 0) is an OTG port whose physical signals are routed to
+  either the DWC2 device controller or the EHCI0/OHCI0 host controller by
+  a hardware mux that follows the USB ID pin.
+
+  USB1 (PHY index 1) is a dedicated host port with no OTG capability.
+
+properties:
+  compatible:
+    const: nuvoton,ma35d1-usb2-phy-otg
+
+  clocks:
+    maxItems: 1
+
+  nuvoton,sys:
+    $ref: /schemas/types.yaml#/definitions/phandle-array
+    items:
+      - items:
+          - description: phandle to the system management syscon.
+          - description: PHY instance index.
+            enum:
+              - 0   # USB0, OTG port (shared with DWC2 gadget controller)
+              - 1   # USB1, host-only port
+    description:
+      A phandle to the syscon node covering the SYS register block, with
+      one argument selecting the PHY instance. Index 0 selects the OTG
+      port PHY (USB0) and index 1 selects the host-only PHY (USB1).
+
+  "#phy-cells":
+    const: 0
+
+  nuvoton,rcalcode:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 0
+    maximum: 15
+    description:
+      Resistor calibration trim code written to the RCALCODE field in
+      USBPMISCR. The 4-bit value adjusts the PHY's internal termination
+      resistance. When absent the hardware reset default is used.
+
+  nuvoton,oc-active-high:
+    type: boolean
+    description:
+      When present, the over-current detect input from the VBUS power
+      switch is treated as active-high. The default (property absent) is
+      active-low. This setting is shared by both USB host ports.
+
+required:
+  - compatible
+  - clocks
+  - nuvoton,sys
+  - "#phy-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/nuvoton,ma35d1-clk.h>
+
+    usb_hphy0: usb-host-phy {
+        compatible = "nuvoton,ma35d1-usb2-phy-otg";
+        clocks = <&clk HUSBH0_GATE>;
+        nuvoton,sys = <&sys 0>;
+        #phy-cells = <0>;
+    };
-- 
2.43.0