[PATCH v0 3/5] arm64: dts: aspeed: Add initial AST2700 SoC device tree
Krzysztof Kozlowski
krzk at kernel.org
Thu Jun 12 23:16:07 PDT 2025
On 13/06/2025 04:29, Ryan Chen wrote:
>> Subject: Re: [PATCH v0 3/5] arm64: dts: aspeed: Add initial AST2700 SoC device
>> tree
>>
>> On 12/06/2025 12:09, Ryan Chen wrote:
>>> This add the initial device tree support for the ASPEED AST2700 SoC.
>>>
>>> - Add top-level compatible string "aspeed,ast2700" and set up
>>> address-cells/size-cells for 64-bit address space.
>>> - Describe a quad-core ARM Cortex-A35 CPU cluster with L2 cache,
>>> including cache properties and PSCI enable-method.
>>> - Add PMU and ARMv8 timer nodes with correct PPI interrupt wiring.
>>> - Model the dual-SoC architecture with two simple-bus nodes:
>>> soc0 (@0x10000000) and soc1 (@0x14000000).
>>> - Add syscon nodes for both SoCs (syscon0, syscon1) with clock/reset
>>> cell definitions and address mapping.
>>> - Add GICv3 interrupt controller node under soc0, with full register
>>> mapping and interrupt properties.
>>> - Hierarchical interrupt controller structure:
>>> - intc0 under soc0, with child intc0_11 node.
>>> - intc1 under soc1, with child intc1_0~intc1_5 nodes.
>>> - Add serial4 node under soc0, others serial node under soc1.
>>>
>>> Signed-off-by: Ryan Chen <ryan_chen at aspeedtech.com>
>>> ---
>>> arch/arm64/boot/dts/aspeed/aspeed-g7.dtsi | 380
>>> ++++++++++++++++++++++
>>> 1 file changed, 380 insertions(+)
>>> create mode 100644 arch/arm64/boot/dts/aspeed/aspeed-g7.dtsi
>>>
>>> diff --git a/arch/arm64/boot/dts/aspeed/aspeed-g7.dtsi
>>> b/arch/arm64/boot/dts/aspeed/aspeed-g7.dtsi
>>> new file mode 100644
>>> index 000000000000..d197187bcf9f
>>> --- /dev/null
>>> +++ b/arch/arm64/boot/dts/aspeed/aspeed-g7.dtsi
>>> @@ -0,0 +1,380 @@
>>> +// SPDX-License-Identifier: GPL-2.0-or-later #include
>>> +<dt-bindings/clock/aspeed,ast2700-scu.h>
>>> +#include <dt-bindings/reset/aspeed,ast2700-scu.h>
>>> +#include <dt-bindings/interrupt-controller/arm-gic.h>
>>> +
>>> +/ {
>>> + #address-cells = <2>;
>>> + #size-cells = <1>;
>>> + interrupt-parent = <&gic>;
>>> +
>>> + cpus {
>>> + #address-cells = <2>;
>>> + #size-cells = <0>;
>>> +
>>> + cpu0: cpu at 0 {
>>> + device_type = "cpu";
>>> + compatible = "arm,cortex-a35";
>>> + reg = <0x0 0x0>;
>>> + enable-method = "psci";
>>> + i-cache-size = <0x8000>;
>>> + i-cache-line-size = <64>;
>>> + i-cache-sets = <256>;
>>> + d-cache-size = <0x8000>;
>>> + d-cache-line-size = <64>;
>>> + d-cache-sets = <128>;
>>> + next-level-cache = <&l2>;
>>> + };
>>> +
>>> + cpu1: cpu at 1 {
>>> + device_type = "cpu";
>>> + compatible = "arm,cortex-a35";
>>> + enable-method = "psci";
>>> + reg = <0x0 0x1>;
>>> + i-cache-size = <0x8000>;
>>> + i-cache-line-size = <64>;
>>> + i-cache-sets = <256>;
>>> + d-cache-size = <0x8000>;
>>> + d-cache-line-size = <64>;
>>> + d-cache-sets = <128>;
>>> + next-level-cache = <&l2>;
>>> + };
>>> +
>>> + cpu2: cpu at 2 {
>>> + device_type = "cpu";
>>> + compatible = "arm,cortex-a35";
>>> + enable-method = "psci";
>>> + reg = <0x0 0x2>;
>>> + i-cache-size = <0x8000>;
>>> + i-cache-line-size = <64>;
>>> + i-cache-sets = <256>;
>>> + d-cache-size = <0x8000>;
>>> + d-cache-line-size = <64>;
>>> + d-cache-sets = <128>;
>>> + next-level-cache = <&l2>;
>>> + };
>>> +
>>> + cpu3: cpu at 3 {
>>> + device_type = "cpu";
>>> + compatible = "arm,cortex-a35";
>>> + enable-method = "psci";
>>> + reg = <0x0 0x3>;
>>> + i-cache-size = <0x8000>;
>>> + i-cache-line-size = <64>;
>>> + i-cache-sets = <256>;
>>> + d-cache-size = <0x8000>;
>>> + d-cache-line-size = <64>;
>>> + d-cache-sets = <128>;
>>> + next-level-cache = <&l2>;
>>> + };
>>> +
>>> + l2: l2-cache0 {
>>> + compatible = "cache";
>>> + cache-level = <2>;
>>> + cache-unified;
>>> + cache-size = <0x80000>;
>>> + cache-line-size = <64>;
>>> + cache-sets = <1024>;
>>> + };
>>> + };
>>> +
>>> + arm-pmu {
>>> + compatible = "arm,cortex-a35-pmu";
>>> + interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) |
>> IRQ_TYPE_LEVEL_HIGH)>;
>>> + };
>>> +
>>> + psci {
>>> + compatible = "arm,psci-1.0";
>>> + method = "smc";
>>> + };
>>> +
>>> + timer {
>>> + compatible = "arm,armv8-timer";
>>> + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) |
>> IRQ_TYPE_LEVEL_LOW)>,
>>> + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) |
>> IRQ_TYPE_LEVEL_LOW)>,
>>> + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) |
>> IRQ_TYPE_LEVEL_LOW)>,
>>> + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) |
>> IRQ_TYPE_LEVEL_LOW)>;
>>> + arm,cpu-registers-not-fw-configured;
>>> + always-on;
>>> + };
>>> +
>>> + soc0: soc at 10000000 {
>>> + compatible = "simple-bus";
>>> + reg = <0x0 0x10000000 0x10000000>;
>>> + #address-cells = <2>;
>>> + #size-cells = <1>;
>>> + ranges;
>>> +
>>> + syscon0: syscon at 12c02000 {
>>> + compatible = "aspeed,ast2700-scu0", "syscon", "simple-mfd";
>>> + reg = <0x0 0x12c02000 0x1000>;
>>> + ranges = <0x0 0x0 0 0x12c02000 0x1000>;
>>> + #address-cells = <2>;
>>> + #size-cells = <1>;
>>> + #clock-cells = <1>;
>>> + #reset-cells = <1>;
>>> + };
>>> +
>>> + gic: interrupt-controller at 12200000 {
>>> + compatible = "arm,gic-v3";
>>> + reg = <0 0x12200000 0x10000>, /* GICD */
>>> + <0 0x12280000 0x80000>, /* GICR */
>>> + <0 0x40440000 0x1000>; /* GICC */
>>> + #interrupt-cells = <3>;
>>> + interrupt-controller;
>>> + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) |
>> IRQ_TYPE_LEVEL_HIGH)>;
>>> + interrupt-parent = <&gic>;
>>> + };
>>> +
>>> + serial4: serial at 12c1a000 {
>>> + compatible = "ns16550a";
>>> + reg = <0x0 0x12c1a000 0x1000>;
>>> + clocks = <&syscon0 SCU0_CLK_GATE_UART4CLK>;
>>> + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
>>> + reg-shift = <2>;
>>> + status = "disabled";
>>> + };
>>> + };
>>> +
>>> + soc1: soc at 14000000 {
>>> + compatible = "simple-bus";
>>> + reg = <0x0 0x14000000 0x10000000>;
>>> + #address-cells = <2>;
>>> + #size-cells = <1>;
>>> + ranges;
>>> +
>>> + syscon1: syscon at 14c02000 {
>>> + compatible = "aspeed,ast2700-scu1", "syscon", "simple-mfd";
>>> + reg = <0x0 0x14c02000 0x1000>;
>>> + ranges = <0x0 0x0 0x0 0x14c02000 0x1000>;
>>> + #address-cells = <2>;
>>> + #size-cells = <1>;
>>> + #clock-cells = <1>;
>>> + #reset-cells = <1>;
>>> + };
>>> +
>>> + serial12: serial at 14c33b00 {
>>> + compatible = "ns16550a";
>>> + reg = <0x0 0x14c33b00 0x100>;
>>> + clocks = <&syscon1 SCU1_CLK_GATE_UART12CLK>;
>>> + interrupts-extended =
>>> + <&intc1_4 18 (GIC_CPU_MASK_SIMPLE(4) |
>> IRQ_TYPE_LEVEL_HIGH)>;
>>> + reg-shift = <2>;
>>> + status = "disabled";
>>> + };
>>> + };
>>> +};
>>> +
>>> +&soc0 {
>>
>> This is the base DTSI, there is no existing node to override. Just define
>> complete SoC node in one place like every other vendor.
>
> My original is use this way, but when I do checkpatch, get
> CHECK: line length of 106 exceeds 100 columns.
> interrupts = <GIC_SPI 192 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
> That the reason modify by this way.
Look how other recent, most developed platforms do it and learn from
them instead of coming with own, confusing style.
>
>>
>>
>>> + intc0: interrupt-controller at 12100000 {
>>> + compatible = "simple-mfd";
>>
>> NAK, never tested.
>>
>> Not allowed, see bindings. And test it next time.
>
> Got it, will update by following.
> Intc0: bus at 12100000 {
> compatible = "simple-bus";
> #address-cells = <2>;
> #size-cells = <1>;
> reg = <0 0x12100000 0x4000>;
> ranges = <0x0 0x0 0x0 0x12100000 0x4000>;
> #address-cells = <2>;
Does not follow DTS coding style and anyway, what sort of bus is this?
Best regards,
Krzysztof
More information about the linux-arm-kernel
mailing list