[PATCH] arm64: dts: renesas: r8a779h0: Add thermal nodes

[Niklas Söderlund]

Hi Geert,

Thanks for your work.

On 2024-03-06 11:58:35 +0100, Geert Uytterhoeven wrote:
> From: Duy Nguyen <duy.nguyen.rh at renesas.com>
> 
> Add device nodes for the Thermal Sensor/Chip Internal Voltage
> Monitor/Core Voltage Monitor (THS/CIVM/CVM) and the various thermal
> zones on the Renesas R-Car V4M (R8A779H0) SoC.
> 
> Add support for 2 TSC nodes of thermal.
> 
> Signed-off-by: Duy Nguyen <duy.nguyen.rh at renesas.com>
> Signed-off-by: Geert Uytterhoeven <geert+renesas at glider.be>

Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas at ragnatech.se>

> ---
> Tested on Renesas Gray Hawk Single with an R-Car V4M SoC that has
> unfortunately no calibration values fused.
> To be queued in renesas-devel for v6.10.
> 
> Changes compared to the BSP:
>   - Drop bogus interrupts property, as interrupts are routed to the ECM,
>   - Change polling-delay from <0> to <1000> as interrupts are not
>     supported.
> ---
>  arch/arm64/boot/dts/renesas/r8a779h0.dtsi | 40 +++++++++++++++++++++++
>  1 file changed, 40 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/renesas/r8a779h0.dtsi b/arch/arm64/boot/dts/renesas/r8a779h0.dtsi
> index 11885729181bc903..a01929231e08fa30 100644
> --- a/arch/arm64/boot/dts/renesas/r8a779h0.dtsi
> +++ b/arch/arm64/boot/dts/renesas/r8a779h0.dtsi
> @@ -318,6 +318,16 @@ sysc: system-controller at e6180000 {
>  			#power-domain-cells = <1>;
>  		};
>  
> +		tsc: thermal at e6198000 {
> +			compatible = "renesas,r8a779h0-thermal";
> +			reg = <0 0xe6198000 0 0x200>,
> +			      <0 0xe61a0000 0 0x200>;
> +			clocks = <&cpg CPG_MOD 919>;
> +			power-domains = <&sysc R8A779H0_PD_ALWAYS_ON>;
> +			resets = <&cpg 919>;
> +			#thermal-sensor-cells = <1>;
> +		};
> +
>  		i2c0: i2c at e6500000 {
>  			compatible = "renesas,i2c-r8a779h0",
>  				     "renesas,rcar-gen4-i2c";
> @@ -653,6 +663,36 @@ prr: chipid at fff00044 {
>  		};
>  	};
>  
> +	thermal-zones {
> +		sensor_thermal_cr52: sensor1-thermal {
> +			polling-delay-passive = <250>;
> +			polling-delay = <1000>;
> +			thermal-sensors = <&tsc 0>;
> +
> +			trips {
> +				sensor1_crit: sensor1-crit {
> +					temperature = <120000>;
> +					hysteresis = <1000>;
> +					type = "critical";
> +				};
> +			};
> +		};
> +
> +		sensor_thermal_ca76: sensor2-thermal {
> +			polling-delay-passive = <250>;
> +			polling-delay = <1000>;
> +			thermal-sensors = <&tsc 1>;
> +
> +			trips {
> +				sensor2_crit: sensor2-crit {
> +					temperature = <120000>;
> +					hysteresis = <1000>;
> +					type = "critical";
> +				};
> +			};
> +		};
> +	};
> +
>  	timer {
>  		compatible = "arm,armv8-timer";
>  		interrupts-extended = <&gic GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
> -- 
> 2.34.1
> 
> 

-- 
Kind Regards,
Niklas Söderlund