[PATCH] arm64: dts: renesas: r8a779h0: Add thermal nodes

[Geert Uytterhoeven]

From: Duy Nguyen <duy.nguyen.rh at renesas.com>

Add device nodes for the Thermal Sensor/Chip Internal Voltage
Monitor/Core Voltage Monitor (THS/CIVM/CVM) and the various thermal
zones on the Renesas R-Car V4M (R8A779H0) SoC.

Add support for 2 TSC nodes of thermal.

Signed-off-by: Duy Nguyen <duy.nguyen.rh at renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas at glider.be>
---
Tested on Renesas Gray Hawk Single with an R-Car V4M SoC that has
unfortunately no calibration values fused.
To be queued in renesas-devel for v6.10.

Changes compared to the BSP:
  - Drop bogus interrupts property, as interrupts are routed to the ECM,
  - Change polling-delay from <0> to <1000> as interrupts are not
    supported.
---
 arch/arm64/boot/dts/renesas/r8a779h0.dtsi | 40 +++++++++++++++++++++++
 1 file changed, 40 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/r8a779h0.dtsi b/arch/arm64/boot/dts/renesas/r8a779h0.dtsi
index 11885729181bc903..a01929231e08fa30 100644
--- a/arch/arm64/boot/dts/renesas/r8a779h0.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a779h0.dtsi
@@ -318,6 +318,16 @@ sysc: system-controller at e6180000 {
 			#power-domain-cells = <1>;
 		};
 
+		tsc: thermal at e6198000 {
+			compatible = "renesas,r8a779h0-thermal";
+			reg = <0 0xe6198000 0 0x200>,
+			      <0 0xe61a0000 0 0x200>;
+			clocks = <&cpg CPG_MOD 919>;
+			power-domains = <&sysc R8A779H0_PD_ALWAYS_ON>;
+			resets = <&cpg 919>;
+			#thermal-sensor-cells = <1>;
+		};
+
 		i2c0: i2c at e6500000 {
 			compatible = "renesas,i2c-r8a779h0",
 				     "renesas,rcar-gen4-i2c";
@@ -653,6 +663,36 @@ prr: chipid at fff00044 {
 		};
 	};
 
+	thermal-zones {
+		sensor_thermal_cr52: sensor1-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+			thermal-sensors = <&tsc 0>;
+
+			trips {
+				sensor1_crit: sensor1-crit {
+					temperature = <120000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		sensor_thermal_ca76: sensor2-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+			thermal-sensors = <&tsc 1>;
+
+			trips {
+				sensor2_crit: sensor2-crit {
+					temperature = <120000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
 	timer {
 		compatible = "arm,armv8-timer";
 		interrupts-extended = <&gic GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
-- 
2.34.1