[PATCH v4 3/6] perf: imx_perf: add support for i.MX95 platform

[Will Deacon]

On Wed, Jan 31, 2024 at 01:58:08PM +0800, Xu Yang wrote:
> i.MX95 has a DDR PMU which is almostly same as i.MX93, it now supports
> read beat and write beat filter capabilities. This will add support for
> i.MX95 and enhance the driver to support specific filter handling for it.
> 
> Usage:
> 
> For read beat:
> ~# perf stat -a -I 1000 -e imx9_ddr0/eddrtq_pm_rd_beat_filt2,counter=3,axi_mask=ID_MASK,axi_id=ID/
> ~# perf stat -a -I 1000 -e imx9_ddr0/eddrtq_pm_rd_beat_filt1,counter=4,axi_mask=ID_MASK,axi_id=ID/
> ~# perf stat -a -I 1000 -e imx9_ddr0/eddrtq_pm_rd_beat_filt0,counter=5,axi_mask=ID_MASK,axi_id=ID/
> eg: For edma2: perf stat -a -I 1000 -e imx9_ddr0/eddrtq_pm_rd_beat_filt0,counter=5,axi_mask=0x00f,axi_id=0x00c/
> 
> For write beat:
> ~# perf stat -a -I 1000 -e imx9_ddr0/eddrtq_pm_wr_beat_filt,counter=2,axi_mask=ID_MASK,axi_id=ID/
> eg: For edma2: perf stat -a -I 1000 -e imx9_ddr0/eddrtq_pm_wr_beat_filt,counter=2,axi_mask=0x00f,axi_id=0x00c/
> 
> Signed-off-by: Xu Yang <xu.yang_2 at nxp.com>
> 
> ---
> Changes in v2:
>  - put soc spefific axi filter events to drvdata according
>    to franks suggestions.
>  - adjust pmcfg axi_id and axi_mask config
> Changes in v3:
>  - no changes
> Changes in v4:
>  - only contain imx95 parts
> ---
>  drivers/perf/fsl_imx9_ddr_perf.c | 86 +++++++++++++++++++++++++++++++-
>  1 file changed, 84 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/perf/fsl_imx9_ddr_perf.c b/drivers/perf/fsl_imx9_ddr_perf.c
> index b1a58e9e1617..85aaaef7212f 100644
> --- a/drivers/perf/fsl_imx9_ddr_perf.c
> +++ b/drivers/perf/fsl_imx9_ddr_perf.c
> @@ -17,9 +17,19 @@
>  #define MX93_PMCFG1_RD_BT_FILT_EN	BIT(29)
>  #define MX93_PMCFG1_ID_MASK		GENMASK(17, 0)
>  
> +#define MX95_PMCFG1_WR_BEAT_FILT_EN	BIT(31)
> +#define MX95_PMCFG1_RD_BEAT_FILT_EN	BIT(30)
> +
>  #define PMCFG2				0x04
>  #define MX93_PMCFG2_ID			GENMASK(17, 0)
>  
> +#define PMCFG3				0x08
> +#define PMCFG4				0x0C
> +#define PMCFG5				0x10
> +#define PMCFG6				0x14
> +#define MX95_PMCFG_ID_MASK		GENMASK(9, 0)
> +#define MX95_PMCFG_ID			GENMASK(25, 16)
> +
>  /* Global control register affects all counters and takes priority over local control registers */
>  #define PMGC0		0x40
>  /* Global control register bits */
> @@ -240,6 +250,18 @@ static struct attribute *imx93_ddr_perf_events_attrs[] = {
>  	NULL,
>  };
>  
> +static struct attribute *imx95_ddr_perf_events_attrs[] = {
> +	/* counter2 specific events */
> +	IMX9_DDR_PMU_EVENT_ATTR(eddrtq_pm_wr_beat_filt, 73),
> +	/* counter3 specific events */
> +	IMX9_DDR_PMU_EVENT_ATTR(eddrtq_pm_rd_beat_filt2, 73),
> +	/* counter4 specific events */
> +	IMX9_DDR_PMU_EVENT_ATTR(eddrtq_pm_rd_beat_filt1, 73),
> +	/* counter5 specific events */
> +	IMX9_DDR_PMU_EVENT_ATTR(eddrtq_pm_rd_beat_filt0, 73),
> +	NULL,
> +};
> +
>  PMU_FORMAT_ATTR(event, "config:0-7");
>  PMU_FORMAT_ATTR(counter, "config:8-15");
>  PMU_FORMAT_ATTR(axi_id, "config1:0-17");
> @@ -271,8 +293,14 @@ static const struct imx_ddr_devtype_data imx93_devtype_data = {
>  	.attrs = imx93_ddr_perf_events_attrs,
>  };
>  
> +static const struct imx_ddr_devtype_data imx95_devtype_data = {
> +	.identifier = "imx95",
> +	.attrs = imx95_ddr_perf_events_attrs,
> +};
> +
>  static const struct of_device_id imx_ddr_pmu_dt_ids[] = {
>  	{ .compatible = "fsl,imx93-ddr-pmu", .data = &imx93_devtype_data },
> +	{ .compatible = "fsl,imx95-ddr-pmu", .data = &imx95_devtype_data },
>  	{ /* sentinel */ }
>  };
>  MODULE_DEVICE_TABLE(of, imx_ddr_pmu_dt_ids);
> @@ -410,6 +438,56 @@ static void imx93_ddr_perf_monitor_config(struct ddr_pmu *pmu, int cfg, int cfg1
>  	writel(pmcfg2, pmu->base + PMCFG2);
>  }
>  
> +static void imx95_ddr_perf_monitor_config(struct ddr_pmu *pmu, int cfg, int cfg1, int cfg2)
> +{
> +	u32 pmcfg1, pmcfg, offset = 0;
> +	int event, counter;
> +
> +	event = cfg & 0x000000FF;
> +	counter = (cfg & 0x0000FF00) >> 8;
> +
> +	pmcfg1 = readl_relaxed(pmu->base + PMCFG1);
> +
> +	if (counter == 2 && event == 73) {
> +		pmcfg1 |= MX95_PMCFG1_WR_BEAT_FILT_EN;
> +		offset = PMCFG3;
> +	} else if (counter == 2 && event != 73) {
> +		pmcfg1 &= ~MX95_PMCFG1_WR_BEAT_FILT_EN;
> +	}
> +
> +	if (counter == 3 && event == 73) {
> +		pmcfg1 |= MX95_PMCFG1_RD_BEAT_FILT_EN;
> +		offset = PMCFG4;
> +	} else if (counter == 3 && event != 73) {
> +		pmcfg1 &= ~MX95_PMCFG1_RD_BEAT_FILT_EN;
> +	}
> +
> +	if (counter == 4 && event == 73) {
> +		pmcfg1 |= MX95_PMCFG1_RD_BEAT_FILT_EN;
> +		offset = PMCFG5;
> +	} else if (counter == 4 && event != 73) {
> +		pmcfg1 &= ~MX95_PMCFG1_RD_BEAT_FILT_EN;
> +	}
> +
> +	if (counter == 5 && event == 73) {
> +		pmcfg1 |= MX95_PMCFG1_RD_BEAT_FILT_EN;
> +		offset = PMCFG6;
> +	} else if (counter == 5 && event != 73) {
> +		pmcfg1 &= ~MX95_PMCFG1_RD_BEAT_FILT_EN;
> +	}

I think this would be much easier to read if you rewrote it as:

	switch (counter) {
	case 2:
		...
		break;
	case 3:


etc.

> +	writel(pmcfg1, pmu->base + PMCFG1);

writel_relaxed()? (since you're already using readl_relaxed()).

> +
> +	if (offset) {
> +		pmcfg = readl_relaxed(pmu->base + offset);
> +		pmcfg &= ~(FIELD_PREP(MX95_PMCFG_ID_MASK, 0x3FF) |
> +			   FIELD_PREP(MX95_PMCFG_ID, 0x3FF));
> +		pmcfg |= (FIELD_PREP(MX95_PMCFG_ID_MASK, cfg2) |
> +			  FIELD_PREP(MX95_PMCFG_ID, cfg1));
> +		writel(pmcfg, pmu->base + offset);

Similarly.

Will