[PATCH v2 2/3] arm64: dts: ti: k3-j721s2: Arranging pin mux in alphabetical order

Udit Kumar u-kumar1 at ti.com
Thu Apr 18 00:16:09 PDT 2024


Arranging pin mux in order of main_pmx0/1, wkup_pmx0/1/2/3.

Signed-off-by: Udit Kumar <u-kumar1 at ti.com>
---
 .../dts/ti/k3-j721s2-common-proc-board.dts    | 29 ++++++++---------
 arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi  | 31 ++++++++++---------
 2 files changed, 31 insertions(+), 29 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
index c5a0b7cbb14f..fed89e34e35e 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
@@ -194,6 +194,21 @@ J721S2_IOPAD(0x038, PIN_OUTPUT, 0) /* (AB28) MCASP0_ACLKX.MCAN5_TX */
 	};
 };
 
+&wkup_pmx1 {
+	mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-default-pins {
+		pinctrl-single,pins = <
+			J721S2_WKUP_IOPAD(0x008, PIN_OUTPUT, 0) /* (A19) MCU_OSPI1_CLK */
+			J721S2_WKUP_IOPAD(0x024, PIN_OUTPUT, 0) /* (D20) MCU_OSPI1_CSn0 */
+			J721S2_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (D21) MCU_OSPI1_D0 */
+			J721S2_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (G20) MCU_OSPI1_D1 */
+			J721S2_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (C20) MCU_OSPI1_D2 */
+			J721S2_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (A20) MCU_OSPI1_D3 */
+			J721S2_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (B19) MCU_OSPI1_DQS */
+			J721S2_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (B20) MCU_OSPI1_LBCLKO */
+		>;
+	};
+};
+
 &wkup_pmx2 {
 	wkup_uart0_pins_default: wkup-uart0-default-pins {
 		pinctrl-single,pins = <
@@ -289,20 +304,6 @@ J721S2_WKUP_IOPAD(0x108, PIN_INPUT, 0) /* (N27) MCU_ADC1_AIN7 */
 	};
 };
 
-&wkup_pmx1 {
-	mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-default-pins {
-		pinctrl-single,pins = <
-			J721S2_WKUP_IOPAD(0x008, PIN_OUTPUT, 0) /* (A19) MCU_OSPI1_CLK */
-			J721S2_WKUP_IOPAD(0x024, PIN_OUTPUT, 0) /* (D20) MCU_OSPI1_CSn0 */
-			J721S2_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (D21) MCU_OSPI1_D0 */
-			J721S2_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (G20) MCU_OSPI1_D1 */
-			J721S2_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (C20) MCU_OSPI1_D2 */
-			J721S2_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (A20) MCU_OSPI1_D3 */
-			J721S2_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (B19) MCU_OSPI1_DQS */
-			J721S2_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (B20) MCU_OSPI1_LBCLKO */
-		>;
-	};
-};
 
 &main_gpio0 {
 	status = "okay";
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
index 623c8421525d..8adf2dfbf3a3 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
@@ -153,6 +153,22 @@ transceiver0: can-phy0 {
 	};
 };
 
+&main_pmx0 {
+	main_i2c0_pins_default: main-i2c0-default-pins {
+		pinctrl-single,pins = <
+			J721S2_IOPAD(0x0e0, PIN_INPUT_PULLUP, 0) /* (AH25) I2C0_SCL */
+			J721S2_IOPAD(0x0e4, PIN_INPUT_PULLUP, 0) /* (AE24) I2C0_SDA */
+		>;
+	};
+
+	main_mcan16_pins_default: main-mcan16-default-pins {
+		pinctrl-single,pins = <
+			J721S2_IOPAD(0x028, PIN_INPUT, 0) /* (AB24) MCAN16_RX */
+			J721S2_IOPAD(0x024, PIN_OUTPUT, 0) /* (Y28) MCAN16_TX */
+		>;
+	};
+};
+
 &wkup_pmx0 {
 	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
 		pinctrl-single,pins = <
@@ -190,21 +206,6 @@ J721S2_WKUP_IOPAD(0x9c, PIN_INPUT, 0) /* (H27) WKUP_I2C0_SDA */
 	};
 };
 
-&main_pmx0 {
-	main_i2c0_pins_default: main-i2c0-default-pins {
-		pinctrl-single,pins = <
-			J721S2_IOPAD(0x0e0, PIN_INPUT_PULLUP, 0) /* (AH25) I2C0_SCL */
-			J721S2_IOPAD(0x0e4, PIN_INPUT_PULLUP, 0) /* (AE24) I2C0_SDA */
-		>;
-	};
-
-	main_mcan16_pins_default: main-mcan16-default-pins {
-		pinctrl-single,pins = <
-			J721S2_IOPAD(0x028, PIN_INPUT, 0) /* (AB24) MCAN16_RX */
-			J721S2_IOPAD(0x024, PIN_OUTPUT, 0) /* (Y28) MCAN16_TX */
-		>;
-	};
-};
 
 &wkup_i2c0 {
 	status = "okay";
-- 
2.34.1




More information about the linux-arm-kernel mailing list