[PATCH v2 1/3] arm64: dts: ti: k3-j784s4-evm: Arranging pin mux in alphabetical order

Udit Kumar u-kumar1 at ti.com
Thu Apr 18 00:16:08 PDT 2024


Arranging pin mux in order of main_pmx0/1, wkup_pmx0/1/2/3

Signed-off-by: Udit Kumar <u-kumar1 at ti.com>
---
 arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 108 +++++++++++------------
 1 file changed, 52 insertions(+), 56 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
index d511b25d62e3..97b0bffc38c5 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
@@ -338,6 +338,58 @@ J784S4_IOPAD(0x010, PIN_INPUT_PULLUP, 8) /* (AH33) MCAN13_RX.I2C4_SDA */
 	};
 };
 
+&wkup_pmx0 {
+	bootph-all;
+	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
+		bootph-all;
+		pinctrl-single,pins = <
+			J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (E32) MCU_OSPI0_CLK */
+			J784S4_WKUP_IOPAD(0x02c, PIN_OUTPUT, 0) /* (A32) MCU_OSPI0_CSn0 */
+			J784S4_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (B33) MCU_OSPI0_D0 */
+			J784S4_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (B32) MCU_OSPI0_D1 */
+			J784S4_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (C33) MCU_OSPI0_D2 */
+			J784S4_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (C35) MCU_OSPI0_D3 */
+			J784S4_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (D33) MCU_OSPI0_D4 */
+			J784S4_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (D34) MCU_OSPI0_D5 */
+			J784S4_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (E34) MCU_OSPI0_D6 */
+			J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (E33) MCU_OSPI0_D7 */
+			J784S4_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (C34) MCU_OSPI0_DQS */
+		>;
+	};
+};
+
+&wkup_pmx1 {
+	bootph-all;
+	mcu_fss0_ospi0_1_pins_default: mcu-fss0-ospi0-1-default-pins {
+		bootph-all;
+		pinctrl-single,pins = <
+			J784S4_WKUP_IOPAD(0x004, PIN_OUTPUT, 6) /* (C32) MCU_OSPI0_ECC_FAIL */
+			J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 6) /* (B34) MCU_OSPI0_RESET_OUT0 */
+		>;
+	};
+
+	mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-default-pins {
+		bootph-all;
+		pinctrl-single,pins = <
+			J784S4_WKUP_IOPAD(0x008, PIN_OUTPUT, 0) /* (F32) MCU_OSPI1_CLK */
+			J784S4_WKUP_IOPAD(0x024, PIN_OUTPUT, 0) /* (G32) MCU_OSPI1_CSn0 */
+			J784S4_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (E35) MCU_OSPI1_D0 */
+			J784S4_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (D31) MCU_OSPI1_D1 */
+			J784S4_WKUP_IOPAD(0x01C, PIN_INPUT, 0) /* (G31) MCU_OSPI1_D2 */
+			J784S4_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (F33) MCU_OSPI1_D3 */
+			J784S4_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (F31) MCU_OSPI1_DQS */
+			J784S4_WKUP_IOPAD(0x00C, PIN_INPUT, 0) /* (C31) MCU_OSPI1_LBCLKO */
+		>;
+	};
+
+	pmic_irq_pins_default: pmic-irq-default-pins {
+		pinctrl-single,pins = <
+			/* (G33) MCU_OSPI1_CSn1.WKUP_GPIO0_39 */
+			J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 7)
+		>;
+	};
+};
+
 &wkup_pmx2 {
 	bootph-all;
 	wkup_uart0_pins_default: wkup-uart0-default-pins {
@@ -417,62 +469,6 @@ J784S4_WKUP_IOPAD(0x108, PIN_INPUT, 0) /* (Y36) MCU_ADC1_AIN7 */
 	};
 };
 
-&wkup_pmx1 {
-	status = "okay";
-
-	pmic_irq_pins_default: pmic-irq-default-pins {
-		pinctrl-single,pins = <
-			/* (G33) MCU_OSPI1_CSn1.WKUP_GPIO0_39 */
-			J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 7)
-		>;
-	};
-};
-
-&wkup_pmx0 {
-	bootph-all;
-	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
-		bootph-all;
-		pinctrl-single,pins = <
-			J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (E32) MCU_OSPI0_CLK */
-			J784S4_WKUP_IOPAD(0x02c, PIN_OUTPUT, 0) /* (A32) MCU_OSPI0_CSn0 */
-			J784S4_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (B33) MCU_OSPI0_D0 */
-			J784S4_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (B32) MCU_OSPI0_D1 */
-			J784S4_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (C33) MCU_OSPI0_D2 */
-			J784S4_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (C35) MCU_OSPI0_D3 */
-			J784S4_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (D33) MCU_OSPI0_D4 */
-			J784S4_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (D34) MCU_OSPI0_D5 */
-			J784S4_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (E34) MCU_OSPI0_D6 */
-			J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (E33) MCU_OSPI0_D7 */
-			J784S4_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (C34) MCU_OSPI0_DQS */
-		>;
-	};
-};
-
-&wkup_pmx1 {
-	bootph-all;
-	mcu_fss0_ospi0_1_pins_default: mcu-fss0-ospi0-1-default-pins {
-		bootph-all;
-		pinctrl-single,pins = <
-			J784S4_WKUP_IOPAD(0x004, PIN_OUTPUT, 6) /* (C32) MCU_OSPI0_ECC_FAIL */
-			J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 6) /* (B34) MCU_OSPI0_RESET_OUT0 */
-		>;
-	};
-
-	mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-default-pins {
-		bootph-all;
-		pinctrl-single,pins = <
-			J784S4_WKUP_IOPAD(0x008, PIN_OUTPUT, 0) /* (F32) MCU_OSPI1_CLK */
-			J784S4_WKUP_IOPAD(0x024, PIN_OUTPUT, 0) /* (G32) MCU_OSPI1_CSn0 */
-			J784S4_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (E35) MCU_OSPI1_D0 */
-			J784S4_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (D31) MCU_OSPI1_D1 */
-			J784S4_WKUP_IOPAD(0x01C, PIN_INPUT, 0) /* (G31) MCU_OSPI1_D2 */
-			J784S4_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (F33) MCU_OSPI1_D3 */
-			J784S4_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (F31) MCU_OSPI1_DQS */
-			J784S4_WKUP_IOPAD(0x00C, PIN_INPUT, 0) /* (C31) MCU_OSPI1_LBCLKO */
-		>;
-	};
-};
-
 &wkup_uart0 {
 	/* Firmware usage */
 	status = "reserved";
-- 
2.34.1




More information about the linux-arm-kernel mailing list