[PATCH 4/8] arm64: dts: ti: k3-am625-beagleplay: Add overlays for OV5640
Andrew Davis
afd at ti.com
Thu Nov 16 06:26:40 PST 2023
On 11/15/23 3:51 AM, Jai Luthra wrote:
> Three different OV5640 modules are supported using the FFC connector on
> BeaglePlay:
> - Digilent PCam 5C
> - ALINX AN5641
> - TEVI-OV5640-*-RPI
>
> The Digilent and ALINX modules supply a 12Mhz XCLK to the sensor, while
> the TEVI module supplies a 24Mhz XCLK, thus requiring a separate
> overlay.
>
> Signed-off-by: Jai Luthra <j-luthra at ti.com>
> ---
> arch/arm64/boot/dts/ti/Makefile | 7 ++
> .../dts/ti/k3-am625-beagleplay-csi2-ov5640.dtso | 77 ++++++++++++++++++++++
> .../ti/k3-am625-beagleplay-csi2-tevi-ov5640.dtso | 77 ++++++++++++++++++++++
> 3 files changed, 161 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
> index 77a347f9f47d..e49e32414560 100644
> --- a/arch/arm64/boot/dts/ti/Makefile
> +++ b/arch/arm64/boot/dts/ti/Makefile
> @@ -9,9 +9,15 @@
> # alphabetically.
>
> # Boards with AM62x SoC
> +k3-am625-beagleplay-csi2-ov5640-dtbs := k3-am625-beagleplay.dtb \
> + k3-am625-beagleplay-csi2-ov5640.dtbo
> +k3-am625-beagleplay-csi2-tevi-ov5640-dtbs := k3-am625-beagleplay.dtb \
> + k3-am625-beagleplay-csi2-tevi-ov5640.dtbo
> k3-am625-sk-hdmi-audio-dtbs := k3-am625-sk.dtb k3-am62x-sk-hdmi-audio.dtbo
> k3-am62-lp-sk-hdmi-audio-dtbs := k3-am62-lp-sk.dtb k3-am62x-sk-hdmi-audio.dtbo
> dtb-$(CONFIG_ARCH_K3) += k3-am625-beagleplay.dtb
> +dtb-$(CONFIG_ARCH_K3) += k3-am625-beagleplay-csi2-ov5640.dtb
> +dtb-$(CONFIG_ARCH_K3) += k3-am625-beagleplay-csi2-tevi-ov5640.dtb
We don't need .dtb files for each overlay combination, you should leave these
as overlays only, and just apply them at boot time as needed.
To test apply them at build time, you can use the CONFIG_OF_ALL_DTBS
method that Rob suggested here[0].
# Build time test only, enabled by CONFIG_OF_ALL_DTBS
dtb- += \
k3-am625-beagleplay-overlay-test1.dtb \
k3-am625-beagleplay-overlay-test2.dtb
k3-am625-beagleplay-overlay-test1-dtbs := k3-am625-beagleplay.dtb \
k3-am625-beagleplay-csi2-ov5640.dtbo
k3-am625-beagleplay-overlay-test1-dtbs := k3-am625-beagleplay.dtb \
k3-am625-beagleplay-csi2-tevi-ov5640.dtbo
dtb-$(CONFIG_ARCH_K3) += k3-am625-beagleplay-csi2-ov5640.dtbo
dtb-$(CONFIG_ARCH_K3) += k3-am625-beagleplay-csi2-tevi-ov5640.dtbo
[0] https://lore.kernel.org/all/CAL_Jsq+8jisrwEqzz7tZnsV9g2+LmThwpO7sHRFA-zh+6q8XuA@mail.gmail.com/
> dtb-$(CONFIG_ARCH_K3) += k3-am625-phyboard-lyra-rdk.dtb
> dtb-$(CONFIG_ARCH_K3) += k3-am625-sk.dtb
> dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-nonwifi-dahlia.dtb
> @@ -81,6 +87,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-am69-sk.dtb
> dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm.dtb
>
> # Enable support for device-tree overlays
> +DTC_FLAGS_k3-am625-beagleplay += -@
Having any DTBO applied to the base during build will add symbols to the
base for you, no need to add this line.
(Please check that this is true for the OF_ALL_DTBS case above, I've not
checked yet, we should fix if not).
I plan to remove the same below in later patches so folks will stop adding
more of these lines.
Andrew
> DTC_FLAGS_k3-am625-sk += -@
> DTC_FLAGS_k3-am62-lp-sk += -@
> DTC_FLAGS_k3-am6548-iot2050-advanced-m2 += -@
> diff --git a/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-ov5640.dtso b/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-ov5640.dtso
> new file mode 100644
> index 000000000000..5e80ca7033ba
> --- /dev/null
> +++ b/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-ov5640.dtso
> @@ -0,0 +1,77 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * ALINX AN5641 & Digilent PCam 5C - OV5640 camera module
> + * Copyright (C) 2022-2023 Texas Instruments Incorporated - https://www.ti.com/
> + */
> +
> +/dts-v1/;
> +/plugin/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +
> +&{/} {
> + clk_ov5640_fixed: ov5640-xclk {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <12000000>;
> + };
> +};
> +
> +&main_gpio0 {
> + p11-hog {
> + /* P11 - CSI2_CAMERA_GPIO1 */
> + gpio-hog;
> + gpios = <11 GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "CSI2_CAMERA_GPIO1";
> + };
> +};
> +
> +&wkup_i2c0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "okay";
> +
> + ov5640: camera at 3c {
> + compatible = "ovti,ov5640";
> + reg = <0x3c>;
> +
> + clocks = <&clk_ov5640_fixed>;
> + clock-names = "xclk";
> +
> + port {
> + csi2_cam0: endpoint {
> + remote-endpoint = <&csi2rx0_in_sensor>;
> + clock-lanes = <0>;
> + data-lanes = <1 2>;
> + };
> + };
> + };
> +};
> +
> +&cdns_csi2rx0 {
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + csi0_port0: port at 0 {
> + reg = <0>;
> + status = "okay";
> +
> + csi2rx0_in_sensor: endpoint {
> + remote-endpoint = <&csi2_cam0>;
> + bus-type = <4>; /* CSI2 DPHY. */
> + clock-lanes = <0>;
> + data-lanes = <1 2>;
> + };
> + };
> + };
> +};
> +
> +&dphy0 {
> + status = "okay";
> +};
> +
> +&ti_csi2rx0 {
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-tevi-ov5640.dtso b/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-tevi-ov5640.dtso
> new file mode 100644
> index 000000000000..5e1cbbc27c8f
> --- /dev/null
> +++ b/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-tevi-ov5640.dtso
> @@ -0,0 +1,77 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Technexion TEVI-OV5640-*-RPI - OV5640 camera module
> + * Copyright (C) 2022-2023 Texas Instruments Incorporated - https://www.ti.com/
> + */
> +
> +/dts-v1/;
> +/plugin/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +
> +&{/} {
> + clk_ov5640_fixed: ov5640-xclk {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <24000000>;
> + };
> +};
> +
> +&main_gpio0 {
> + p11-hog {
> + /* P11 - CSI2_CAMERA_GPIO1 */
> + gpio-hog;
> + gpios = <11 GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "CSI2_CAMERA_GPIO1";
> + };
> +};
> +
> +&wkup_i2c0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "okay";
> +
> + ov5640: camera at 3c {
> + compatible = "ovti,ov5640";
> + reg = <0x3c>;
> +
> + clocks = <&clk_ov5640_fixed>;
> + clock-names = "xclk";
> +
> + port {
> + csi2_cam0: endpoint {
> + remote-endpoint = <&csi2rx0_in_sensor>;
> + clock-lanes = <0>;
> + data-lanes = <1 2>;
> + };
> + };
> + };
> +};
> +
> +&cdns_csi2rx0 {
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + csi0_port0: port at 0 {
> + reg = <0>;
> + status = "okay";
> +
> + csi2rx0_in_sensor: endpoint {
> + remote-endpoint = <&csi2_cam0>;
> + bus-type = <4>; /* CSI2 DPHY. */
> + clock-lanes = <0>;
> + data-lanes = <1 2>;
> + };
> + };
> + };
> +};
> +
> +&dphy0 {
> + status = "okay";
> +};
> +
> +&ti_csi2rx0 {
> + status = "okay";
> +};
>
More information about the linux-arm-kernel
mailing list