[PATCH 4/8] arm64: dts: ti: k3-am625-beagleplay: Add overlays for OV5640

[Jai Luthra]

Three different OV5640 modules are supported using the FFC connector on
BeaglePlay:
- Digilent PCam 5C
- ALINX AN5641
- TEVI-OV5640-*-RPI

The Digilent and ALINX modules supply a 12Mhz XCLK to the sensor, while
the TEVI module supplies a 24Mhz XCLK, thus requiring a separate
overlay.

Signed-off-by: Jai Luthra <j-luthra at ti.com>
---
 arch/arm64/boot/dts/ti/Makefile                    |  7 ++
 .../dts/ti/k3-am625-beagleplay-csi2-ov5640.dtso    | 77 ++++++++++++++++++++++
 .../ti/k3-am625-beagleplay-csi2-tevi-ov5640.dtso   | 77 ++++++++++++++++++++++
 3 files changed, 161 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index 77a347f9f47d..e49e32414560 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -9,9 +9,15 @@
 # alphabetically.
 
 # Boards with AM62x SoC
+k3-am625-beagleplay-csi2-ov5640-dtbs := k3-am625-beagleplay.dtb \
+	k3-am625-beagleplay-csi2-ov5640.dtbo
+k3-am625-beagleplay-csi2-tevi-ov5640-dtbs := k3-am625-beagleplay.dtb \
+	k3-am625-beagleplay-csi2-tevi-ov5640.dtbo
 k3-am625-sk-hdmi-audio-dtbs := k3-am625-sk.dtb k3-am62x-sk-hdmi-audio.dtbo
 k3-am62-lp-sk-hdmi-audio-dtbs := k3-am62-lp-sk.dtb k3-am62x-sk-hdmi-audio.dtbo
 dtb-$(CONFIG_ARCH_K3) += k3-am625-beagleplay.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-am625-beagleplay-csi2-ov5640.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-am625-beagleplay-csi2-tevi-ov5640.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am625-phyboard-lyra-rdk.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am625-sk.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-nonwifi-dahlia.dtb
@@ -81,6 +87,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-am69-sk.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm.dtb
 
 # Enable support for device-tree overlays
+DTC_FLAGS_k3-am625-beagleplay += -@
 DTC_FLAGS_k3-am625-sk += -@
 DTC_FLAGS_k3-am62-lp-sk += -@
 DTC_FLAGS_k3-am6548-iot2050-advanced-m2 += -@
diff --git a/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-ov5640.dtso b/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-ov5640.dtso
new file mode 100644
index 000000000000..5e80ca7033ba
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-ov5640.dtso
@@ -0,0 +1,77 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ALINX AN5641 & Digilent PCam 5C - OV5640 camera module
+ * Copyright (C) 2022-2023 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+&{/} {
+	clk_ov5640_fixed: ov5640-xclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <12000000>;
+	};
+};
+
+&main_gpio0 {
+	p11-hog {
+		/* P11 - CSI2_CAMERA_GPIO1 */
+		gpio-hog;
+		gpios = <11 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "CSI2_CAMERA_GPIO1";
+	};
+};
+
+&wkup_i2c0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	ov5640: camera at 3c {
+		compatible = "ovti,ov5640";
+		reg = <0x3c>;
+
+		clocks = <&clk_ov5640_fixed>;
+		clock-names = "xclk";
+
+		port {
+			csi2_cam0: endpoint {
+				remote-endpoint = <&csi2rx0_in_sensor>;
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+			};
+		};
+	};
+};
+
+&cdns_csi2rx0 {
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		csi0_port0: port at 0 {
+			reg = <0>;
+			status = "okay";
+
+			csi2rx0_in_sensor: endpoint {
+				remote-endpoint = <&csi2_cam0>;
+				bus-type = <4>; /* CSI2 DPHY. */
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+			};
+		};
+	};
+};
+
+&dphy0 {
+	status = "okay";
+};
+
+&ti_csi2rx0 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-tevi-ov5640.dtso b/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-tevi-ov5640.dtso
new file mode 100644
index 000000000000..5e1cbbc27c8f
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-tevi-ov5640.dtso
@@ -0,0 +1,77 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Technexion TEVI-OV5640-*-RPI - OV5640 camera module
+ * Copyright (C) 2022-2023 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+&{/} {
+	clk_ov5640_fixed: ov5640-xclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+	};
+};
+
+&main_gpio0 {
+	p11-hog {
+		/* P11 - CSI2_CAMERA_GPIO1 */
+		gpio-hog;
+		gpios = <11 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "CSI2_CAMERA_GPIO1";
+	};
+};
+
+&wkup_i2c0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	ov5640: camera at 3c {
+		compatible = "ovti,ov5640";
+		reg = <0x3c>;
+
+		clocks = <&clk_ov5640_fixed>;
+		clock-names = "xclk";
+
+		port {
+			csi2_cam0: endpoint {
+				remote-endpoint = <&csi2rx0_in_sensor>;
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+			};
+		};
+	};
+};
+
+&cdns_csi2rx0 {
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		csi0_port0: port at 0 {
+			reg = <0>;
+			status = "okay";
+
+			csi2rx0_in_sensor: endpoint {
+				remote-endpoint = <&csi2_cam0>;
+				bus-type = <4>; /* CSI2 DPHY. */
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+			};
+		};
+	};
+};
+
+&dphy0 {
+	status = "okay";
+};
+
+&ti_csi2rx0 {
+	status = "okay";
+};

-- 
2.42.1