[PATCH v2] arm64: dts: ti: k3-j784s4-evm: Enable MCU CPSW2G

[Andrew Davis]

On 3/14/23 11:25 PM, Siddharth Vadapalli wrote:
> Add device tree support to enable MCU CPSW with J784S4 EVM.
> 
> Signed-off-by: Siddharth Vadapalli <s-vadapalli at ti.com>
> ---
> Hello,
> 
> Please do not merge this patch until the following have been merged:
> 1. https://lore.kernel.org/r/20230314085500.10597-1-j-choudhary@ti.com/
> 2. https://lore.kernel.org/r/20230314152611.140969-2-j-choudhary@ti.com/
> 3. https://lore.kernel.org/r/20230308201513.116638-1-j-choudhary@ti.com/
> 
> Changes from v1:
> 1. Drop patch for adding device id property for mcu_navss. This patch is
>     now a part of another series at:
>     https://lore.kernel.org/r/20230314152611.140969-2-j-choudhary@ti.com/
> 2. Move "mcu_mdio_pins_default" pinctrl to the "davinci_mdio" node.
> 

LGTM,

Reviewed-by: Andrew Davis <afd at ti.com>

> v1:
> https://lore.kernel.org/r/20230314104055.1475054-1-s-vadapalli@ti.com/
> 
>   arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 50 ++++++++++++++++++++++++
>   1 file changed, 50 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
> index 8cd4a7ecc121..476ad8915c5b 100644
> --- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
> +++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
> @@ -140,6 +140,32 @@ J784S4_IOPAD(0x020, PIN_INPUT, 7) /* (AJ35) MCAN15_RX.GPIO0_8 */
>   	};
>   };
>   
> +&wkup_pmx0 {
> +	mcu_cpsw_pins_default: mcu-cpsw-pins-default {
> +		pinctrl-single,pins = <
> +			J784S4_WKUP_IOPAD(0x094, PIN_INPUT, 0) /* (A35) MCU_RGMII1_RD0 */
> +			J784S4_WKUP_IOPAD(0x090, PIN_INPUT, 0) /* (B36) MCU_RGMII1_RD1 */
> +			J784S4_WKUP_IOPAD(0x08c, PIN_INPUT, 0) /* (C36) MCU_RGMII1_RD2 */
> +			J784S4_WKUP_IOPAD(0x088, PIN_INPUT, 0) /* (D36) MCU_RGMII1_RD3 */
> +			J784S4_WKUP_IOPAD(0x084, PIN_INPUT, 0) /* (B37) MCU_RGMII1_RXC */
> +			J784S4_WKUP_IOPAD(0x06c, PIN_INPUT, 0) /* (C37) MCU_RGMII1_RX_CTL */
> +			J784S4_WKUP_IOPAD(0x07c, PIN_OUTPUT, 0) /* (D37) MCU_RGMII1_TD0 */
> +			J784S4_WKUP_IOPAD(0x078, PIN_OUTPUT, 0) /* (D38) MCU_RGMII1_TD1 */
> +			J784S4_WKUP_IOPAD(0x074, PIN_OUTPUT, 0) /* (E37) MCU_RGMII1_TD2 */
> +			J784S4_WKUP_IOPAD(0x070, PIN_OUTPUT, 0) /* (E38) MCU_RGMII1_TD3 */
> +			J784S4_WKUP_IOPAD(0x080, PIN_OUTPUT, 0) /* (E36) MCU_RGMII1_TXC */
> +			J784S4_WKUP_IOPAD(0x068, PIN_OUTPUT, 0) /* (C38) MCU_RGMII1_TX_CTL */
> +		>;
> +	};
> +
> +	mcu_mdio_pins_default: mcu-mdio-pins-default {
> +		pinctrl-single,pins = <
> +			J784S4_WKUP_IOPAD(0x09c, PIN_OUTPUT, 0) /* (A36) MCU_MDIO0_MDC */
> +			J784S4_WKUP_IOPAD(0x098, PIN_INPUT, 0) /* (B35) MCU_MDIO0_MDIO */
> +		>;
> +	};
> +};
> +
>   &main_uart8 {
>   	status = "okay";
>   	pinctrl-names = "default";
> @@ -194,3 +220,27 @@ &main_sdhci1 {
>   &main_gpio0 {
>   	status = "okay";
>   };
> +
> +&mcu_cpsw {
> +	status = "okay";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&mcu_cpsw_pins_default>;
> +};
> +
> +&davinci_mdio {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&mcu_mdio_pins_default>;
> +
> +	mcu_phy0: ethernet-phy at 0 {
> +		reg = <0>;
> +		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
> +		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
> +		ti,min-output-impedance;
> +	};
> +};
> +
> +&mcu_cpsw_port1 {
> +	status = "okay";
> +	phy-mode = "rgmii-rxid";
> +	phy-handle = <&mcu_phy0>;
> +};