[PATCH v2] arm64: dts: ti: k3-j784s4-evm: Enable MCU CPSW2G

[Siddharth Vadapalli]

Add device tree support to enable MCU CPSW with J784S4 EVM.

Signed-off-by: Siddharth Vadapalli <s-vadapalli at ti.com>
---
Hello,

Please do not merge this patch until the following have been merged:
1. https://lore.kernel.org/r/20230314085500.10597-1-j-choudhary@ti.com/
2. https://lore.kernel.org/r/20230314152611.140969-2-j-choudhary@ti.com/
3. https://lore.kernel.org/r/20230308201513.116638-1-j-choudhary@ti.com/

Changes from v1:
1. Drop patch for adding device id property for mcu_navss. This patch is
   now a part of another series at:
   https://lore.kernel.org/r/20230314152611.140969-2-j-choudhary@ti.com/
2. Move "mcu_mdio_pins_default" pinctrl to the "davinci_mdio" node.

v1:
https://lore.kernel.org/r/20230314104055.1475054-1-s-vadapalli@ti.com/

 arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 50 ++++++++++++++++++++++++
 1 file changed, 50 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
index 8cd4a7ecc121..476ad8915c5b 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
@@ -140,6 +140,32 @@ J784S4_IOPAD(0x020, PIN_INPUT, 7) /* (AJ35) MCAN15_RX.GPIO0_8 */
 	};
 };
 
+&wkup_pmx0 {
+	mcu_cpsw_pins_default: mcu-cpsw-pins-default {
+		pinctrl-single,pins = <
+			J784S4_WKUP_IOPAD(0x094, PIN_INPUT, 0) /* (A35) MCU_RGMII1_RD0 */
+			J784S4_WKUP_IOPAD(0x090, PIN_INPUT, 0) /* (B36) MCU_RGMII1_RD1 */
+			J784S4_WKUP_IOPAD(0x08c, PIN_INPUT, 0) /* (C36) MCU_RGMII1_RD2 */
+			J784S4_WKUP_IOPAD(0x088, PIN_INPUT, 0) /* (D36) MCU_RGMII1_RD3 */
+			J784S4_WKUP_IOPAD(0x084, PIN_INPUT, 0) /* (B37) MCU_RGMII1_RXC */
+			J784S4_WKUP_IOPAD(0x06c, PIN_INPUT, 0) /* (C37) MCU_RGMII1_RX_CTL */
+			J784S4_WKUP_IOPAD(0x07c, PIN_OUTPUT, 0) /* (D37) MCU_RGMII1_TD0 */
+			J784S4_WKUP_IOPAD(0x078, PIN_OUTPUT, 0) /* (D38) MCU_RGMII1_TD1 */
+			J784S4_WKUP_IOPAD(0x074, PIN_OUTPUT, 0) /* (E37) MCU_RGMII1_TD2 */
+			J784S4_WKUP_IOPAD(0x070, PIN_OUTPUT, 0) /* (E38) MCU_RGMII1_TD3 */
+			J784S4_WKUP_IOPAD(0x080, PIN_OUTPUT, 0) /* (E36) MCU_RGMII1_TXC */
+			J784S4_WKUP_IOPAD(0x068, PIN_OUTPUT, 0) /* (C38) MCU_RGMII1_TX_CTL */
+		>;
+	};
+
+	mcu_mdio_pins_default: mcu-mdio-pins-default {
+		pinctrl-single,pins = <
+			J784S4_WKUP_IOPAD(0x09c, PIN_OUTPUT, 0) /* (A36) MCU_MDIO0_MDC */
+			J784S4_WKUP_IOPAD(0x098, PIN_INPUT, 0) /* (B35) MCU_MDIO0_MDIO */
+		>;
+	};
+};
+
 &main_uart8 {
 	status = "okay";
 	pinctrl-names = "default";
@@ -194,3 +220,27 @@ &main_sdhci1 {
 &main_gpio0 {
 	status = "okay";
 };
+
+&mcu_cpsw {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_cpsw_pins_default>;
+};
+
+&davinci_mdio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_mdio_pins_default>;
+
+	mcu_phy0: ethernet-phy at 0 {
+		reg = <0>;
+		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+		ti,min-output-impedance;
+	};
+};
+
+&mcu_cpsw_port1 {
+	status = "okay";
+	phy-mode = "rgmii-rxid";
+	phy-handle = <&mcu_phy0>;
+};
-- 
2.25.1