[PATCH 6/9] drm: atmel_hlcdc: Add support for XLCDC in atmel LCD driver
Claudiu.Beznea at microchip.com
Claudiu.Beznea at microchip.com
Wed Jun 14 00:10:17 PDT 2023
On 13.06.2023 10:04, Manikandan Muralidharan wrote:
> - XLCDC in SAM9X7 has different sets of registers and additional
> configuration bits when compared to previous HLCDC IP. Read/write
> operation on the controller registers is now separated using the
> XLCDC status flag.
> - HEO scaling, window resampling, Alpha blending, YUV-to-RGB
> conversion in XLCDC is derived and handled using additional
> configuration bits and registers.
> - Writing one to the Enable fields of each layer in LCD_ATTRE
> is required to reflect the values set in Configuration, FBA, Enable
> registers of each layer
>
> Signed-off-by: Manikandan Muralidharan <manikandan.m at microchip.com>
> [Hari.PrasathGE at microchip.com: update the attribute field for each layer]
> Signed-off-by: Hari Prasath Gujulan Elango <Hari.PrasathGE at microchip.com>
> [durai.manickamkr at microchip.com: implement status flag to seprate register update]
> Signed-off-by: Durai Manickam KR <durai.manickamkr at microchip.com>
> ---
> .../gpu/drm/atmel-hlcdc/atmel_hlcdc_crtc.c | 28 +-
> .../gpu/drm/atmel-hlcdc/atmel_hlcdc_plane.c | 297 ++++++++++++++----
> 2 files changed, 256 insertions(+), 69 deletions(-)
>
> diff --git a/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_crtc.c b/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_crtc.c
> index 58184cd6ab0b..7c9cf7c0c75d 100644
> --- a/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_crtc.c
> +++ b/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_crtc.c
> @@ -139,10 +139,10 @@ static void atmel_hlcdc_crtc_mode_set_nofb(struct drm_crtc *c)
> state = drm_crtc_state_to_atmel_hlcdc_crtc_state(c->state);
> cfg = state->output_mode << 8;
>
> - if (adj->flags & DRM_MODE_FLAG_NVSYNC)
> + if (!crtc->dc->is_xlcdc && (adj->flags & DRM_MODE_FLAG_NVSYNC))
> cfg |= ATMEL_HLCDC_VSPOL;
>
> - if (adj->flags & DRM_MODE_FLAG_NHSYNC)
> + if (!crtc->dc->is_xlcdc && (adj->flags & DRM_MODE_FLAG_NHSYNC))
> cfg |= ATMEL_HLCDC_HSPOL;
>
> regmap_update_bits(regmap, ATMEL_HLCDC_CFG(5),
> @@ -177,6 +177,18 @@ static void atmel_hlcdc_crtc_atomic_disable(struct drm_crtc *c,
>
> pm_runtime_get_sync(dev->dev);
>
> + if (crtc->dc->is_xlcdc) {
> + regmap_write(regmap, ATMEL_HLCDC_DIS, ATMEL_XLCDC_CM);
> + while (!regmap_read(regmap, ATMEL_HLCDC_SR, &status) &&
> + (status & ATMEL_XLCDC_CM))
> + cpu_relax();
A timeout would be god here to avoid potential infinite loop (for different
reasons). You can check regmap_read_poll_timeout(). Same for the rest of
while loops above.
> +
> + regmap_write(regmap, ATMEL_HLCDC_DIS, ATMEL_XLCDC_SD);
> + while (!regmap_read(regmap, ATMEL_HLCDC_SR, &status) &&
> + !(status & ATMEL_XLCDC_SD))
> + cpu_relax();
> + }
> +
> regmap_write(regmap, ATMEL_HLCDC_DIS, ATMEL_HLCDC_DISP);
> while (!regmap_read(regmap, ATMEL_HLCDC_SR, &status) &&
> (status & ATMEL_HLCDC_DISP))
> @@ -231,6 +243,18 @@ static void atmel_hlcdc_crtc_atomic_enable(struct drm_crtc *c,
> !(status & ATMEL_HLCDC_DISP))
> cpu_relax();
>
> + if (crtc->dc->is_xlcdc) {
> + regmap_write(regmap, ATMEL_HLCDC_EN, ATMEL_XLCDC_CM);
> + while (!regmap_read(regmap, ATMEL_HLCDC_SR, &status) &&
> + !(status & ATMEL_XLCDC_CM))
> + cpu_relax();
> +
> + regmap_write(regmap, ATMEL_HLCDC_EN, ATMEL_XLCDC_SD);
> + while (!regmap_read(regmap, ATMEL_HLCDC_SR, &status) &&
> + (status & ATMEL_XLCDC_SD))
> + cpu_relax();
> + }
> +
> pm_runtime_put_sync(dev->dev);
>
> }
> diff --git a/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_plane.c b/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_plane.c
> index daa508504f47..fe33476818c4 100644
> --- a/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_plane.c
> +++ b/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_plane.c
> @@ -330,11 +330,59 @@ static void atmel_hlcdc_plane_setup_scaler(struct atmel_hlcdc_plane *plane,
> yfactor));
> }
>
> +static void atmel_xlcdc_plane_setup_scaler(struct atmel_hlcdc_plane *plane,
> + struct atmel_hlcdc_plane_state *state)
> +{
> + const struct atmel_hlcdc_layer_desc *desc = plane->layer.desc;
> + u32 xfactor, yfactor;
> +
> + if (!desc->layout.scaler_config)
> + return;
> +
> + if (state->crtc_w == state->src_w && state->crtc_h == state->src_h) {
> + atmel_hlcdc_layer_write_cfg(&plane->layer,
> + desc->layout.scaler_config, 0);
> + return;
> + }
> +
> + /* xfactor = round[(2^20 * XMEMSIZE)/XSIZE)] */
> + xfactor = (1048576 * state->src_w) / state->crtc_w;
> +
> + /* yfactor = round[(2^20 * YMEMSIZE)/YSIZE)] */
> + yfactor = (1048576 * state->src_h) / state->crtc_h;
> +
> + atmel_hlcdc_layer_write_cfg(&plane->layer, desc->layout.scaler_config,
> + ATMEL_XLCDC_LAYER_VSCALER_LUMA_ENABLE |
> + ATMEL_XLCDC_LAYER_VSCALER_CHROMA_ENABLE |
> + ATMEL_XLCDC_LAYER_HSCALER_LUMA_ENABLE |
> + ATMEL_XLCDC_LAYER_HSCALER_CHROMA_ENABLE);
> +
> + atmel_hlcdc_layer_write_cfg(&plane->layer, desc->layout.scaler_config + 1,
> + yfactor);
> + atmel_hlcdc_layer_write_cfg(&plane->layer, desc->layout.scaler_config + 3,
> + xfactor);
> +
> + /* As per YCbCr window resampling configuration */
> + if (state->base.fb->format->format == DRM_FORMAT_YUV420) {
> + atmel_hlcdc_layer_write_cfg(&plane->layer, desc->layout.scaler_config + 2,
> + yfactor / 2);
> + atmel_hlcdc_layer_write_cfg(&plane->layer, desc->layout.scaler_config + 4,
> + xfactor / 2);
> + } else {
> + /* As per ARGB window resampling configuration */
> + atmel_hlcdc_layer_write_cfg(&plane->layer, desc->layout.scaler_config + 2,
> + yfactor);
> + atmel_hlcdc_layer_write_cfg(&plane->layer, desc->layout.scaler_config + 4,
> + xfactor);
> + }
> +}
> +
> static void
> atmel_hlcdc_plane_update_pos_and_size(struct atmel_hlcdc_plane *plane,
> struct atmel_hlcdc_plane_state *state)
> {
> const struct atmel_hlcdc_layer_desc *desc = plane->layer.desc;
> + struct atmel_hlcdc_dc *dc = plane->base.dev->dev_private;
>
> if (desc->layout.size)
> atmel_hlcdc_layer_write_cfg(&plane->layer, desc->layout.size,
> @@ -352,7 +400,10 @@ atmel_hlcdc_plane_update_pos_and_size(struct atmel_hlcdc_plane *plane,
> ATMEL_HLCDC_LAYER_POS(state->crtc_x,
> state->crtc_y));
>
> - atmel_hlcdc_plane_setup_scaler(plane, state);
> + if (!(dc->is_xlcdc))
You can reverse the logic here to avoid !dc->is_xlcdc. Also, no need for ()
around dc->is_xlcdc
> + atmel_hlcdc_plane_setup_scaler(plane, state);
> + else
> + atmel_xlcdc_plane_setup_scaler(plane, state);
> }
>
> static void
> @@ -362,33 +413,58 @@ atmel_hlcdc_plane_update_general_settings(struct atmel_hlcdc_plane *plane,
> unsigned int cfg = ATMEL_HLCDC_LAYER_DMA_BLEN_INCR16 | state->ahb_id;
> const struct atmel_hlcdc_layer_desc *desc = plane->layer.desc;
> const struct drm_format_info *format = state->base.fb->format;
> -
extra line
> + struct atmel_hlcdc_dc *dc = plane->base.dev->dev_private;
> /*
> * Rotation optimization is not working on RGB888 (rotation is still
> * working but without any optimization).
> */
> - if (format->format == DRM_FORMAT_RGB888)
> + if ((!(dc->is_xlcdc)) && format->format == DRM_FORMAT_RGB888)
No need for extra ().
> cfg |= ATMEL_HLCDC_LAYER_DMA_ROTDIS;
>
> - atmel_hlcdc_layer_write_cfg(&plane->layer, ATMEL_HLCDC_LAYER_DMA_CFG,
> - cfg);
> + if (!(dc->is_xlcdc)) {
no need for extra ()
> + atmel_hlcdc_layer_write_cfg(&plane->layer, ATMEL_HLCDC_LAYER_DMA_CFG,
> + cfg);
>
> - cfg = ATMEL_HLCDC_LAYER_DMA | ATMEL_HLCDC_LAYER_REP;
> + cfg = ATMEL_HLCDC_LAYER_DMA | ATMEL_HLCDC_LAYER_REP;
> + } else {
> + atmel_hlcdc_layer_write_cfg(&plane->layer, ATMEL_XLCDC_LAYER_DMA_CFG,
> + cfg);
> +
> + cfg = ATMEL_XLCDC_LAYER_DMA | ATMEL_XLCDC_LAYER_REP;
> + }
>
> if (plane->base.type != DRM_PLANE_TYPE_PRIMARY) {
> - cfg |= ATMEL_HLCDC_LAYER_OVR | ATMEL_HLCDC_LAYER_ITER2BL |
> - ATMEL_HLCDC_LAYER_ITER;
> + if (!(dc->is_xlcdc)) {
no need for extra (). Same for the rest of occurencies above. Also, you can
reverse the logic to avoid ! in front of (dc->is_xlcdc)
> + cfg |= ATMEL_HLCDC_LAYER_OVR | ATMEL_HLCDC_LAYER_ITER2BL |
> + ATMEL_HLCDC_LAYER_ITER;
> +
> + if (format->has_alpha)
> + cfg |= ATMEL_HLCDC_LAYER_LAEN;
> + else
> + cfg |= ATMEL_HLCDC_LAYER_GAEN |
> + ATMEL_HLCDC_LAYER_GA(state->base.alpha);
> + } else {
> + /*
> + * Alpha Blending bits specific to SAM9X7 SoC
> + */
> + cfg |= ATMEL_XLCDC_LAYER_SFACTC_A0_MULT_AS |
> + ATMEL_XLCDC_LAYER_SFACTA_ONE |
> + ATMEL_XLCDC_LAYER_DFACTC_M_A0_MULT_AS |
> + ATMEL_XLCDC_LAYER_DFACTA_ONE;
> + if (format->has_alpha)
> + cfg |= ATMEL_XLCDC_LAYER_A0(0xff);
> + else
> + cfg |= ATMEL_XLCDC_LAYER_A0(state->base.alpha);
> + }
> + }
>
> - if (format->has_alpha)
> - cfg |= ATMEL_HLCDC_LAYER_LAEN;
> + if (state->disc_h && state->disc_w) {
> + if (!(dc->is_xlcdc))
> + cfg |= ATMEL_HLCDC_LAYER_DISCEN;
> else
> - cfg |= ATMEL_HLCDC_LAYER_GAEN |
> - ATMEL_HLCDC_LAYER_GA(state->base.alpha);
> + cfg |= ATMEL_XLCDC_LAYER_DISCEN;
> }
>
> - if (state->disc_h && state->disc_w)
> - cfg |= ATMEL_HLCDC_LAYER_DISCEN;
> -
> atmel_hlcdc_layer_write_cfg(&plane->layer, desc->layout.general_config,
> cfg);
> }
> @@ -441,33 +517,42 @@ static void atmel_hlcdc_plane_update_buffers(struct atmel_hlcdc_plane *plane,
> struct atmel_hlcdc_plane_state *state)
> {
> const struct atmel_hlcdc_layer_desc *desc = plane->layer.desc;
> + struct atmel_hlcdc_dc *dc = plane->base.dev->dev_private;
> struct drm_framebuffer *fb = state->base.fb;
> u32 sr;
> int i;
>
> - sr = atmel_hlcdc_layer_read_reg(&plane->layer, ATMEL_HLCDC_LAYER_CHSR);
> + if (!(dc->is_xlcdc))
You can reverse the logic
> + sr = atmel_hlcdc_layer_read_reg(&plane->layer, ATMEL_HLCDC_LAYER_CHSR);
> + else
> + sr = atmel_hlcdc_layer_read_reg(&plane->layer, ATMEL_XLCDC_LAYER_ENR);
>
> for (i = 0; i < state->nplanes; i++) {
> struct drm_gem_dma_object *gem = drm_fb_dma_get_gem_obj(fb, i);
>
> state->dscrs[i]->addr = gem->dma_addr + state->offsets[i];
>
> - atmel_hlcdc_layer_write_reg(&plane->layer,
> - ATMEL_HLCDC_LAYER_PLANE_HEAD(i),
> - state->dscrs[i]->self);
> -
> - if (!(sr & ATMEL_HLCDC_LAYER_EN)) {
> - atmel_hlcdc_layer_write_reg(&plane->layer,
> - ATMEL_HLCDC_LAYER_PLANE_ADDR(i),
> - state->dscrs[i]->addr);
> + if (!(dc->is_xlcdc)) {
you can reverse the logic
> atmel_hlcdc_layer_write_reg(&plane->layer,
> - ATMEL_HLCDC_LAYER_PLANE_CTRL(i),
> - state->dscrs[i]->ctrl);
> + ATMEL_HLCDC_LAYER_PLANE_HEAD(i),
> + state->dscrs[i]->self);
> +
> + if (!(sr & ATMEL_HLCDC_LAYER_EN)) {
> + atmel_hlcdc_layer_write_reg(&plane->layer,
> + ATMEL_HLCDC_LAYER_PLANE_ADDR(i),
> + state->dscrs[i]->addr);
> + atmel_hlcdc_layer_write_reg(&plane->layer,
> + ATMEL_HLCDC_LAYER_PLANE_CTRL(i),
> + state->dscrs[i]->ctrl);
> + atmel_hlcdc_layer_write_reg(&plane->layer,
> + ATMEL_HLCDC_LAYER_PLANE_NEXT(i),
> + state->dscrs[i]->self);
> + }
> + } else {
> atmel_hlcdc_layer_write_reg(&plane->layer,
> - ATMEL_HLCDC_LAYER_PLANE_NEXT(i),
> - state->dscrs[i]->self);
> + ATMEL_XLCDC_LAYER_PLANE_ADDR(i),
> + state->dscrs[i]->addr);
> }
> -
> if (desc->layout.xstride[i])
> atmel_hlcdc_layer_write_cfg(&plane->layer,
> desc->layout.xstride[i],
> @@ -716,19 +801,31 @@ static void atmel_hlcdc_plane_atomic_disable(struct drm_plane *p,
> struct drm_atomic_state *state)
> {
> struct atmel_hlcdc_plane *plane = drm_plane_to_atmel_hlcdc_plane(p);
> -
You can keep this line afte the above variable.
> + struct atmel_hlcdc_dc *dc = plane->base.dev->dev_private;
> /* Disable interrupts */
> - atmel_hlcdc_layer_write_reg(&plane->layer, ATMEL_HLCDC_LAYER_IDR,
> - 0xffffffff);
> + if (!(dc->is_xlcdc))
you can reverse the logic
> + atmel_hlcdc_layer_write_reg(&plane->layer, ATMEL_HLCDC_LAYER_IDR,
> + 0xffffffff);
> + else
> + atmel_hlcdc_layer_write_reg(&plane->layer, ATMEL_XLCDC_LAYER_IDR,
> + 0xffffffff);
>
> /* Disable the layer */
> - atmel_hlcdc_layer_write_reg(&plane->layer, ATMEL_HLCDC_LAYER_CHDR,
> - ATMEL_HLCDC_LAYER_RST |
> - ATMEL_HLCDC_LAYER_A2Q |
> - ATMEL_HLCDC_LAYER_UPDATE);
> + if (!(dc->is_xlcdc))
same here.
> + atmel_hlcdc_layer_write_reg(&plane->layer,
> + ATMEL_HLCDC_LAYER_CHDR,
> + ATMEL_HLCDC_LAYER_RST |
> + ATMEL_HLCDC_LAYER_A2Q |
> + ATMEL_HLCDC_LAYER_UPDATE);
> + else
> + atmel_hlcdc_layer_write_reg(&plane->layer,
> + ATMEL_XLCDC_LAYER_ENR, 0);
>
> /* Clear all pending interrupts */
> - atmel_hlcdc_layer_read_reg(&plane->layer, ATMEL_HLCDC_LAYER_ISR);
> + if (!(dc->is_xlcdc))
> + atmel_hlcdc_layer_read_reg(&plane->layer, ATMEL_HLCDC_LAYER_ISR);
> + else
> + atmel_hlcdc_layer_read_reg(&plane->layer, ATMEL_XLCDC_LAYER_ISR);
> }
>
> static void atmel_hlcdc_plane_atomic_update(struct drm_plane *p,
> @@ -739,6 +836,7 @@ static void atmel_hlcdc_plane_atomic_update(struct drm_plane *p,
> struct atmel_hlcdc_plane *plane = drm_plane_to_atmel_hlcdc_plane(p);
> struct atmel_hlcdc_plane_state *hstate =
> drm_plane_state_to_atmel_hlcdc_plane_state(new_s);
> + struct atmel_hlcdc_dc *dc = p->dev->dev_private;
> u32 sr;
>
> if (!new_s->crtc || !new_s->fb)
> @@ -756,23 +854,46 @@ static void atmel_hlcdc_plane_atomic_update(struct drm_plane *p,
> atmel_hlcdc_plane_update_buffers(plane, hstate);
> atmel_hlcdc_plane_update_disc_area(plane, hstate);
>
> - /* Enable the overrun interrupts. */
> - atmel_hlcdc_layer_write_reg(&plane->layer, ATMEL_HLCDC_LAYER_IER,
> - ATMEL_HLCDC_LAYER_OVR_IRQ(0) |
> - ATMEL_HLCDC_LAYER_OVR_IRQ(1) |
> - ATMEL_HLCDC_LAYER_OVR_IRQ(2));
> -
> - /* Apply the new config at the next SOF event. */
> - sr = atmel_hlcdc_layer_read_reg(&plane->layer, ATMEL_HLCDC_LAYER_CHSR);
> - atmel_hlcdc_layer_write_reg(&plane->layer, ATMEL_HLCDC_LAYER_CHER,
> - ATMEL_HLCDC_LAYER_UPDATE |
> - (sr & ATMEL_HLCDC_LAYER_EN ?
> - ATMEL_HLCDC_LAYER_A2Q : ATMEL_HLCDC_LAYER_EN));
> + if (!(dc->is_xlcdc)) {
same here
> + /* Enable the overrun interrupts. */
> + atmel_hlcdc_layer_write_reg(&plane->layer, ATMEL_HLCDC_LAYER_IER,
> + ATMEL_HLCDC_LAYER_OVR_IRQ(0) |
> + ATMEL_HLCDC_LAYER_OVR_IRQ(1) |
> + ATMEL_HLCDC_LAYER_OVR_IRQ(2));
> +
> + /* Apply the new config at the next SOF event. */
> + sr = atmel_hlcdc_layer_read_reg(&plane->layer, ATMEL_HLCDC_LAYER_CHSR);
> + atmel_hlcdc_layer_write_reg(&plane->layer, ATMEL_HLCDC_LAYER_CHER,
> + ATMEL_HLCDC_LAYER_UPDATE |
> + (sr & ATMEL_HLCDC_LAYER_EN ?
> + ATMEL_HLCDC_LAYER_A2Q : ATMEL_HLCDC_LAYER_EN));
> + } else {
> + /* Enable the overrun interrupts. */
> + atmel_hlcdc_layer_write_reg(&plane->layer, ATMEL_XLCDC_LAYER_IER,
> + ATMEL_XLCDC_LAYER_OVR_IRQ(0) |
> + ATMEL_XLCDC_LAYER_OVR_IRQ(1) |
> + ATMEL_XLCDC_LAYER_OVR_IRQ(2));
> +
> + atmel_hlcdc_layer_write_reg(&plane->layer, ATMEL_XLCDC_LAYER_ENR,
> + ATMEL_XLCDC_LAYER_EN);
> + }
> +
> + /*
> + * Updating XLCDC_xxxCFGx, XLCDC_xxxFBA and XLCDC_xxxEN,
> + * (where xxx indicates each layer) requires writing one to the
> + * Update Attribute field for each layer in LCDC_ATTRE register for SAM9X7.
> + */
> + if (dc->is_xlcdc) {
> + regmap_write(dc->hlcdc->regmap, ATMEL_XLCDC_ATTRE, ATMEL_XLCDC_BASE_UPDATE |
> + ATMEL_XLCDC_OVR1_UPDATE | ATMEL_XLCDC_OVR3_UPDATE |
> + ATMEL_XLCDC_HEO_UPDATE);
> + }
> }
>
> static int atmel_hlcdc_plane_init_properties(struct atmel_hlcdc_plane *plane)
> {
> const struct atmel_hlcdc_layer_desc *desc = plane->layer.desc;
> + struct atmel_hlcdc_dc *dc = plane->base.dev->dev_private;
>
> if (desc->type == ATMEL_HLCDC_OVERLAY_LAYER ||
> desc->type == ATMEL_HLCDC_CURSOR_LAYER) {
> @@ -796,20 +917,50 @@ static int atmel_hlcdc_plane_init_properties(struct atmel_hlcdc_plane *plane)
> return ret;
> }
>
> - if (desc->layout.csc) {
> + if (!(dc->is_xlcdc)) {
you can reverse the logic
> + if (desc->layout.csc) {
> + /*
> + * TODO: decare a "yuv-to-rgb-conv-factors" property to let
> + * userspace modify these factors (using a BLOB property ?).
> + */
> + atmel_hlcdc_layer_write_cfg(&plane->layer,
> + desc->layout.csc,
> + 0x4c900091);
> + atmel_hlcdc_layer_write_cfg(&plane->layer,
> + desc->layout.csc + 1,
> + 0x7a5f5090);
> + atmel_hlcdc_layer_write_cfg(&plane->layer,
> + desc->layout.csc + 2,
> + 0x40040890);
> + }
> + } else {
> /*
> - * TODO: decare a "yuv-to-rgb-conv-factors" property to let
> - * userspace modify these factors (using a BLOB property ?).
> + * yuv-to-rgb-conv-factors are now defined from LCDC_HEOCFG16 to
> + * LCDC_HEOCFG21 registers in SAM9X7.
> */
> - atmel_hlcdc_layer_write_cfg(&plane->layer,
> - desc->layout.csc,
> - 0x4c900091);
> - atmel_hlcdc_layer_write_cfg(&plane->layer,
> - desc->layout.csc + 1,
> - 0x7a5f5090);
> - atmel_hlcdc_layer_write_cfg(&plane->layer,
> - desc->layout.csc + 2,
> - 0x40040890);
> + if (desc->layout.csc) {
> + atmel_hlcdc_layer_write_cfg(&plane->layer,
> + desc->layout.csc,
> + 0x00000488);
> + atmel_hlcdc_layer_write_cfg(&plane->layer,
> + desc->layout.csc + 1,
> + 0x00000648);
> + atmel_hlcdc_layer_write_cfg(&plane->layer,
> + desc->layout.csc + 2,
> + 0x1EA00480);
> + atmel_hlcdc_layer_write_cfg(&plane->layer,
> + desc->layout.csc + 3,
> + 0x00001D28);
> + atmel_hlcdc_layer_write_cfg(&plane->layer,
> + desc->layout.csc + 4,
> + 0x08100480);
> + atmel_hlcdc_layer_write_cfg(&plane->layer,
> + desc->layout.csc + 5,
> + 0x00000000);
> + atmel_hlcdc_layer_write_cfg(&plane->layer,
> + desc->layout.csc + 6,
> + 0x00000007);
> + }
> }
>
> return 0;
> @@ -819,19 +970,31 @@ void atmel_hlcdc_plane_irq(struct atmel_hlcdc_plane *plane)
> {
> const struct atmel_hlcdc_layer_desc *desc = plane->layer.desc;
> u32 isr;
> + struct atmel_hlcdc_dc *dc = plane->base.dev->dev_private;
>
> - isr = atmel_hlcdc_layer_read_reg(&plane->layer, ATMEL_HLCDC_LAYER_ISR);
> + if (!(dc->is_xlcdc))
same here.
> + isr = atmel_hlcdc_layer_read_reg(&plane->layer, ATMEL_HLCDC_LAYER_ISR);
> + else
> + isr = atmel_hlcdc_layer_read_reg(&plane->layer, ATMEL_XLCDC_LAYER_ISR);
>
> /*
> * There's not much we can do in case of overrun except informing
> * the user. However, we are in interrupt context here, hence the
> * use of dev_dbg().
> */
> - if (isr &
> - (ATMEL_HLCDC_LAYER_OVR_IRQ(0) | ATMEL_HLCDC_LAYER_OVR_IRQ(1) |
> - ATMEL_HLCDC_LAYER_OVR_IRQ(2)))
> - dev_dbg(plane->base.dev->dev, "overrun on plane %s\n",
> - desc->name);
> + if (!(dc->is_xlcdc)) {
> + if (isr &
> + (ATMEL_HLCDC_LAYER_OVR_IRQ(0) | ATMEL_HLCDC_LAYER_OVR_IRQ(1) |
> + ATMEL_HLCDC_LAYER_OVR_IRQ(2)))
> + dev_dbg(plane->base.dev->dev, "overrun on plane %s\n",
> + desc->name);
> + } else {
> + if (isr &
> + (ATMEL_XLCDC_LAYER_OVR_IRQ(0) | ATMEL_XLCDC_LAYER_OVR_IRQ(1) |
> + ATMEL_XLCDC_LAYER_OVR_IRQ(2)))
> + dev_dbg(plane->base.dev->dev, "overrun on plane %s\n",
> + desc->name);
> + }
> }
>
> static const struct drm_plane_helper_funcs atmel_hlcdc_layer_plane_helper_funcs = {
More information about the linux-arm-kernel
mailing list