[PATCH] clk: imx: composite-8m: Add imx8m_divider_determine_rate

[Adam Ford]

On Mon, Jun 12, 2023 at 11:08 AM Maxime Ripard <maxime at cerno.tech> wrote:
>
> On Sun, Jun 11, 2023 at 12:02:42PM -0500, Adam Ford wrote:
> > On Tue, Jun 6, 2023 at 1:45 PM Fabio Estevam <festevam at gmail.com> wrote:
> > >
> > > On Sat, May 6, 2023 at 4:53 PM Adam Ford <aford173 at gmail.com> wrote:
> > > >
> > > > Currently, certain clocks are derrived as a divider from their
> > > > parent clock.  For some clocks, even when CLK_SET_RATE_PARENT
> > > > is set, the parent clock is not properly set which can lead
> > > > to some relatively inaccurate clock values.
> > > >
> >
> > + Maxime
> >
> > > > Unlike imx/clk-composite-93 and imx/clk-divider-gate, it
> > > > cannot rely on calling a standard determine_rate function,
> > > > because the 8m composite clocks have a pre-divider and
> > > > post-divider. Because of this, a custom determine_rate
> > > > function is necessary to determine the maximum clock
> > > > division which is equivalent to pre-divider * the
> > > > post-divider.
> > > >
> > > > With this added, the system can attempt to adjust the parent rate
> > > > when the proper flags are set which can lead to a more precise clock
> > > > value.
> > > >
> > > > On the imx8mplus, no clock changes are present.
> > > > On the Mini and Nano, this can help achieve more accurate
> > > > lcdif clocks. When trying to get a pixel clock of 31.500MHz
> > > > on an imx8m Nano, the clocks divided the 594MHz down, but
> > > > left the parent rate untouched which caused a calulation error.
> > > >
> > > > Before:
> > > > video_pll              594000000
> > > >   video_pll_bypass     594000000
> > > >     video_pll_out      594000000
> > > >       disp_pixel       31263158
> > > >         disp_pixel_clk 31263158
> > > >
> > > > Variance = -236842 Hz
> > > >
> > > > After this patch:
> > > > video_pll               31500000
> > > >   video_pll_bypass      31500000
> > > >     video_pll_out       31500000
> > > >       disp_pixel        31500000
> > > >         disp_pixel_clk  31500000
> > > >
> > > > Variance = 0 Hz
> > > >
> > > > All other clocks rates and parent were the same.
> > > > Similar results on imx8mm were found.
> > > >
> > > > Fixes: 690dccc4a0bf ("Revert "clk: imx: composite-8m: Add support to determine_rate"")
> > > > Signed-off-by: Adam Ford <aford173 at gmail.com>
> > >
> >
> > Peng / Abel,
> >
> > Any suggestions on how we can move this forward?  Looking at the
> > clk-composite-8m driver, imx8m_clk_composite_compute_dividers uses the
> > max values which is basically what my patch does.  There was some
> > discussion about making determine_rate mandatory for muxes[1] and this
> > patch should help with this in addition to making it easier to sync
> > more video resolutions on the 8m Mini and Nano.
>
> Those patches have been queued by Stephen for 6.6 :)

One of the patches in the older series was reverted, but this was to
address the patch that was reverted.

adam
>
> Maxime