[PATCH v7 1/4] arm64: dts: qcom: sc8280xp: Define some of the display blocks
Johan Hovold
johan at kernel.org
Wed Jan 11 05:21:05 PST 2023
On Tue, Jan 10, 2023 at 07:59:03PM -0800, Bjorn Andersson wrote:
> From: Bjorn Andersson <bjorn.andersson at linaro.org>
>
> Define the display clock controllers, the MDSS instances, the DP phys
> and connect these together.
>
> Signed-off-by: Bjorn Andersson <bjorn.andersson at linaro.org>
> Signed-off-by: Bjorn Andersson <quic_bjorande at quicinc.com>
> ---
>
> Changes since v6:
> - Dropped assigned-clock-rate on MDP_CLK
> - Rearranged the properties in all nodes
>
> arch/arm64/boot/dts/qcom/sc8280xp.dtsi | 811 +++++++++++++++++++++++++
> 1 file changed, 811 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
> index 0ea2f19d471b..2ed17baf50d3 100644
> --- a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
> + mdss0_mdp: display-controller at ae01000 {
> + compatible = "qcom,sc8280xp-dpu";
> + reg = <0 0x0ae01000 0 0x8f000>,
> + <0 0x0aeb0000 0 0x2008>;
> + reg-names = "mdp", "vbif";
> +
> + clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
> + <&gcc GCC_DISP_SF_AXI_CLK>,
> + <&dispcc0 DISP_CC_MDSS_AHB_CLK>,
> + <&dispcc0 DISP_CC_MDSS_MDP_LUT_CLK>,
> + <&dispcc0 DISP_CC_MDSS_MDP_CLK>,
> + <&dispcc0 DISP_CC_MDSS_VSYNC_CLK>;
> + clock-names = "bus",
> + "nrt_bus",
> + "iface",
> + "lut",
> + "core",
> + "vsync";
> + interrupt-parent = <&mdss0>;
> + interrupts = <0>;
> + power-domains = <&rpmhpd SC8280XP_MMCX>;
> +
> + assigned-clocks = <&dispcc0 DISP_CC_MDSS_VSYNC_CLK>;
> + assigned-clock-rates = <19200000>;
Nit: Shouldn't these come after the clock-names property as they did in
v5 so that the clock properties are grouped?
> + operating-points-v2 = <&mdss0_mdp_opp_table>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port at 5 {
> + reg = <5>;
> + mdss0_intf5_out: endpoint {
> + remote-endpoint = <&mdss0_dp3_in>;
> + };
> + };
> +
> + port at 6 {
> + reg = <6>;
> + mdss0_intf6_out: endpoint {
> + remote-endpoint = <&mdss0_dp2_in>;
> + };
> + };
> + };
> + mdss0_dp2: displayport-controller at ae9a000 {
> + compatible = "qcom,sc8280xp-dp";
> + reg = <0 0xae9a000 0 0x200>,
> + <0 0xae9a200 0 0x200>,
> + <0 0xae9a400 0 0x600>,
> + <0 0xae9b000 0 0x400>;
> +
> + clocks = <&dispcc0 DISP_CC_MDSS_AHB_CLK>,
> + <&dispcc0 DISP_CC_MDSS_DPTX2_AUX_CLK>,
> + <&dispcc0 DISP_CC_MDSS_DPTX2_LINK_CLK>,
> + <&dispcc0 DISP_CC_MDSS_DPTX2_LINK_INTF_CLK>,
> + <&dispcc0 DISP_CC_MDSS_DPTX2_PIXEL0_CLK>;
> + clock-names = "core_iface", "core_aux",
> + "ctrl_link",
> + "ctrl_link_iface", "stream_pixel";
> + interrupt-parent = <&mdss0>;
> + interrupts = <14>;
> + phys = <&mdss0_dp2_phy>;
> + phy-names = "dp";
> + power-domains = <&rpmhpd SC8280XP_MMCX>;
> +
> + assigned-clocks = <&dispcc0 DISP_CC_MDSS_DPTX2_LINK_CLK_SRC>,
> + <&dispcc0 DISP_CC_MDSS_DPTX2_PIXEL0_CLK_SRC>;
> + assigned-clock-parents = <&mdss0_dp2_phy 0>, <&mdss0_dp2_phy 1>;
Same here.
> + operating-points-v2 = <&mdss0_dp2_opp_table>;
> +
> + #sound-dai-cells = <0>;
> +
> + status = "disabled";
> + mdss0_dp3: displayport-controller at aea0000 {
> + compatible = "qcom,sc8280xp-dp";
> + reg = <0 0xaea0000 0 0x200>,
> + <0 0xaea0200 0 0x200>,
> + <0 0xaea0400 0 0x600>,
> + <0 0xaea1000 0 0x400>;
> +
> + clocks = <&dispcc0 DISP_CC_MDSS_AHB_CLK>,
> + <&dispcc0 DISP_CC_MDSS_DPTX3_AUX_CLK>,
> + <&dispcc0 DISP_CC_MDSS_DPTX3_LINK_CLK>,
> + <&dispcc0 DISP_CC_MDSS_DPTX3_LINK_INTF_CLK>,
> + <&dispcc0 DISP_CC_MDSS_DPTX3_PIXEL0_CLK>;
> + clock-names = "core_iface", "core_aux",
> + "ctrl_link",
> + "ctrl_link_iface", "stream_pixel";
> + interrupt-parent = <&mdss0>;
> + interrupts = <15>;
> + phys = <&mdss0_dp3_phy>;
> + phy-names = "dp";
> + power-domains = <&dispcc0 MDSS_GDSC>;
> +
> + assigned-clocks = <&dispcc0 DISP_CC_MDSS_DPTX3_LINK_CLK_SRC>,
> + <&dispcc0 DISP_CC_MDSS_DPTX3_PIXEL0_CLK_SRC>;
> + assigned-clock-parents = <&mdss0_dp3_phy 0>, <&mdss0_dp3_phy 1>;
And here.
> + operating-points-v2 = <&mdss0_dp3_opp_table>;
> +
> + #sound-dai-cells = <0>;
> +
> + status = "disabled";
> + mdss1: display-subsystem at 22000000 {
> + compatible = "qcom,sc8280xp-mdss";
> + reg = <0 0x22000000 0 0x1000>;
> + reg-names = "mdss";
> +
> + clocks = <&gcc GCC_DISP_AHB_CLK>,
> + <&dispcc1 DISP_CC_MDSS_AHB_CLK>,
> + <&dispcc1 DISP_CC_MDSS_MDP_CLK>;
> + clock-names = "iface",
> + "ahb",
> + "core";
> + interconnects = <&mmss_noc MASTER_MDP_CORE1_0 0 &mc_virt SLAVE_EBI1 0>,
> + <&mmss_noc MASTER_MDP_CORE1_1 0 &mc_virt SLAVE_EBI1 0>;
> + interconnect-names = "mdp0-mem", "mdp1-mem";
> + interrupts = <GIC_SPI 865 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-controller;
This is a provider property so perhaps it should go before
'#interrupt-cells' as it did above?
> +
> + iommus = <&apps_smmu 0x1800 0x402>;
> + power-domains = <&dispcc1 MDSS_GDSC>;
> + resets = <&dispcc1 DISP_CC_MDSS_CORE_BCR>;
> +
> + #interrupt-cells = <1>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + status = "disabled";
> +
> + mdss1_mdp: display-controller at 22001000 {
> + compatible = "qcom,sc8280xp-dpu";
> + reg = <0 0x22001000 0 0x8f000>,
> + <0 0x220b0000 0 0x2008>;
> + reg-names = "mdp", "vbif";
> +
> + clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
> + <&gcc GCC_DISP_SF_AXI_CLK>,
> + <&dispcc1 DISP_CC_MDSS_AHB_CLK>,
> + <&dispcc1 DISP_CC_MDSS_MDP_LUT_CLK>,
> + <&dispcc1 DISP_CC_MDSS_MDP_CLK>,
> + <&dispcc1 DISP_CC_MDSS_VSYNC_CLK>;
> + clock-names = "bus",
> + "nrt_bus",
> + "iface",
> + "lut",
> + "core",
> + "vsync";
> + interrupt-parent = <&mdss1>;
> + interrupts = <0>;
> + power-domains = <&rpmhpd SC8280XP_MMCX>;
> +
> + assigned-clocks = <&dispcc1 DISP_CC_MDSS_VSYNC_CLK>;
> + assigned-clock-rates = <19200000>;
Move after 'clock-names'?
There are a few more instances like this below.
Johan
More information about the linux-arm-kernel
mailing list