[PATCH v5 0/5] ARM: Add GXP I2C Support

[nick.hawkins at hpe.com]

From: Nick Hawkins <nick.hawkins at hpe.com>

The GXP SoC supports 10 I2C engines. Each I2C engine is completely
independent and can function both as an I2C master and I2C slave. The
I2C master can operate in a multi master environment. The engines support
a scalable speed from 8kHZ to 1.5 Mhz.

---
Changes since v4:
 *Removed use of i2c_global_init_done
 *Removed use of if else case for inline conditional
 *Removed error messages for timeouts and NACKS
 *Added bit definitions to replace magic values
 *Fix build error
 *Relocate Kconfig definition
Changes since v3:
 *Switch engine variable to u32
 *Disable IRQ on device remove with register write instead
 *Provided even greater description with the use of Phandle
Changes since v2:
 *Disable IRQ on a device remove
 *Remove use of I2C_CLASS_DEPRECATED
 *Use i2c_parse_fw_timings instead of of_property_read_u32
 *Remove redundant dev_err_probe as platform_get_irq already has one
 *Used __iomem instead of res->start to find physical address
 *Use BIT in gxp_i2c_irq_handler
 *Made value u8 instead of u16 for u8 read
 *Provided a better description of Phandle in yaml
Changes since v1:
 *Removed yaml documentation of hpe,gxp-sysreg as it has been
  applied to syscon.yaml
 *Made i2cX a generic node name i2c in dts file
 *Added status field to the dtsi and the dts for i2c bus
 *Removed unnecessary size-cells and address-cells from yaml
 *Removed phandle from hpe,sysreg-phandle
 *Changed hpe,i2c-max-bus-freq to clock-frequency
 *Removed rogue tab in structure definition
 *Removed use of __iomem *base local variables as it was
  unnecessary
 *Switched #if IS_ENABLED() -> if (IS_ENABLED()) inside
  functions
 *Removed use of pr_* functions
 *Removed informational prints in register and unregister
  functions
 *Removed print from interrupt handler
 *Removed informational prints from probe function
 *Switched dev_err -> dev_err_probe in probe function
 *Used the respective helper for mapping the resource to
  __iomem*

Nick Hawkins (5):
  i2c: hpe: Add GXP SoC I2C Controller
  dt-bindings: i2c: Add hpe,gxp-i2c
  ARM: dts: hpe: Add I2C Topology
  ARM: multi_v7_defconfig: add gxp i2c module
  MAINTAINERS: Add HPE GXP I2C Support

 .../devicetree/bindings/i2c/hpe,gxp-i2c.yaml  |  59 ++
 MAINTAINERS                                   |   2 +
 arch/arm/boot/dts/hpe-bmc-dl360gen10.dts      | 109 +++
 arch/arm/boot/dts/hpe-gxp.dtsi                | 125 ++++
 arch/arm/configs/multi_v7_defconfig           |   1 +
 drivers/i2c/busses/Kconfig                    |   7 +
 drivers/i2c/busses/Makefile                   |   1 +
 drivers/i2c/busses/i2c-gxp.c                  | 620 ++++++++++++++++++
 8 files changed, 924 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/i2c/hpe,gxp-i2c.yaml
 create mode 100644 drivers/i2c/busses/i2c-gxp.c

-- 
2.17.1