[PATCH v4 12/12] net: dsa: mt7530: use external PCS driver
Daniel Golle
daniel at makrotopia.org
Fri Feb 10 15:40:40 PST 2023
Implement regmap access wrappers, for now only to be used by the
pcs-mtk driver.
Make use of external PCS driver and drop the reduntant implementation
in mt7530.c.
As a nice side effect the SGMII registers can now also more easily be
inspected for debugging via /sys/kernel/debug/regmap.
Tested-by: Bjørn Mork <bjorn at mork.no>
Signed-off-by: Daniel Golle <daniel at makrotopia.org>
---
drivers/net/dsa/Kconfig | 1 +
drivers/net/dsa/mt7530.c | 277 ++++++++++-----------------------------
drivers/net/dsa/mt7530.h | 47 +------
3 files changed, 71 insertions(+), 254 deletions(-)
diff --git a/drivers/net/dsa/Kconfig b/drivers/net/dsa/Kconfig
index f6f3b43dfb06..6b45fa8b6907 100644
--- a/drivers/net/dsa/Kconfig
+++ b/drivers/net/dsa/Kconfig
@@ -38,6 +38,7 @@ config NET_DSA_MT7530
tristate "MediaTek MT7530 and MT7531 Ethernet switch support"
select NET_DSA_TAG_MTK
select MEDIATEK_GE_PHY
+ select PCS_MTK_LYNXI
help
This enables support for the MediaTek MT7530 and MT7531 Ethernet
switch chips. Multi-chip module MT7530 in MT7621AT, MT7621DAT,
diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index 3a15015bc409..582ba30374c8 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -14,6 +14,7 @@
#include <linux/of_mdio.h>
#include <linux/of_net.h>
#include <linux/of_platform.h>
+#include <linux/pcs/pcs-mtk-lynxi.h>
#include <linux/phylink.h>
#include <linux/regmap.h>
#include <linux/regulator/consumer.h>
@@ -2567,128 +2568,11 @@ static int mt7531_rgmii_setup(struct mt7530_priv *priv, u32 port,
return 0;
}
-static void mt7531_pcs_link_up(struct phylink_pcs *pcs, unsigned int mode,
- phy_interface_t interface, int speed, int duplex)
-{
- struct mt7530_priv *priv = pcs_to_mt753x_pcs(pcs)->priv;
- int port = pcs_to_mt753x_pcs(pcs)->port;
- unsigned int val;
-
- /* For adjusting speed and duplex of SGMII force mode. */
- if (interface != PHY_INTERFACE_MODE_SGMII ||
- phylink_autoneg_inband(mode))
- return;
-
- /* SGMII force mode setting */
- val = mt7530_read(priv, MT7531_SGMII_MODE(port));
- val &= ~MT7531_SGMII_IF_MODE_MASK;
-
- switch (speed) {
- case SPEED_10:
- val |= MT7531_SGMII_FORCE_SPEED_10;
- break;
- case SPEED_100:
- val |= MT7531_SGMII_FORCE_SPEED_100;
- break;
- case SPEED_1000:
- val |= MT7531_SGMII_FORCE_SPEED_1000;
- break;
- }
-
- /* MT7531 SGMII 1G force mode can only work in full duplex mode,
- * no matter MT7531_SGMII_FORCE_HALF_DUPLEX is set or not.
- *
- * The speed check is unnecessary as the MAC capabilities apply
- * this restriction. --rmk
- */
- if ((speed == SPEED_10 || speed == SPEED_100) &&
- duplex != DUPLEX_FULL)
- val |= MT7531_SGMII_FORCE_HALF_DUPLEX;
-
- mt7530_write(priv, MT7531_SGMII_MODE(port), val);
-}
-
static bool mt753x_is_mac_port(u32 port)
{
return (port == 5 || port == 6);
}
-static int mt7531_sgmii_setup_mode_force(struct mt7530_priv *priv, u32 port,
- phy_interface_t interface)
-{
- u32 val;
-
- if (!mt753x_is_mac_port(port))
- return -EINVAL;
-
- mt7530_set(priv, MT7531_QPHY_PWR_STATE_CTRL(port),
- MT7531_SGMII_PHYA_PWD);
-
- val = mt7530_read(priv, MT7531_PHYA_CTRL_SIGNAL3(port));
- val &= ~MT7531_RG_TPHY_SPEED_MASK;
- /* Setup 2.5 times faster clock for 2.5Gbps data speeds with 10B/8B
- * encoding.
- */
- val |= (interface == PHY_INTERFACE_MODE_2500BASEX) ?
- MT7531_RG_TPHY_SPEED_3_125G : MT7531_RG_TPHY_SPEED_1_25G;
- mt7530_write(priv, MT7531_PHYA_CTRL_SIGNAL3(port), val);
-
- mt7530_clear(priv, MT7531_PCS_CONTROL_1(port), MT7531_SGMII_AN_ENABLE);
-
- /* MT7531 SGMII 1G and 2.5G force mode can only work in full duplex
- * mode, no matter MT7531_SGMII_FORCE_HALF_DUPLEX is set or not.
- */
- mt7530_rmw(priv, MT7531_SGMII_MODE(port),
- MT7531_SGMII_IF_MODE_MASK | MT7531_SGMII_REMOTE_FAULT_DIS,
- MT7531_SGMII_FORCE_SPEED_1000);
-
- mt7530_write(priv, MT7531_QPHY_PWR_STATE_CTRL(port), 0);
-
- return 0;
-}
-
-static int mt7531_sgmii_setup_mode_an(struct mt7530_priv *priv, int port,
- phy_interface_t interface)
-{
- if (!mt753x_is_mac_port(port))
- return -EINVAL;
-
- mt7530_set(priv, MT7531_QPHY_PWR_STATE_CTRL(port),
- MT7531_SGMII_PHYA_PWD);
-
- mt7530_rmw(priv, MT7531_PHYA_CTRL_SIGNAL3(port),
- MT7531_RG_TPHY_SPEED_MASK, MT7531_RG_TPHY_SPEED_1_25G);
-
- mt7530_set(priv, MT7531_SGMII_MODE(port),
- MT7531_SGMII_REMOTE_FAULT_DIS |
- MT7531_SGMII_SPEED_DUPLEX_AN);
-
- mt7530_rmw(priv, MT7531_PCS_SPEED_ABILITY(port),
- MT7531_SGMII_TX_CONFIG_MASK, 1);
-
- mt7530_set(priv, MT7531_PCS_CONTROL_1(port), MT7531_SGMII_AN_ENABLE);
-
- mt7530_set(priv, MT7531_PCS_CONTROL_1(port), MT7531_SGMII_AN_RESTART);
-
- mt7530_write(priv, MT7531_QPHY_PWR_STATE_CTRL(port), 0);
-
- return 0;
-}
-
-static void mt7531_pcs_an_restart(struct phylink_pcs *pcs)
-{
- struct mt7530_priv *priv = pcs_to_mt753x_pcs(pcs)->priv;
- int port = pcs_to_mt753x_pcs(pcs)->port;
- u32 val;
-
- /* Only restart AN when AN is enabled */
- val = mt7530_read(priv, MT7531_PCS_CONTROL_1(port));
- if (val & MT7531_SGMII_AN_ENABLE) {
- val |= MT7531_SGMII_AN_RESTART;
- mt7530_write(priv, MT7531_PCS_CONTROL_1(port), val);
- }
-}
-
static int
mt7531_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
phy_interface_t interface)
@@ -2711,11 +2595,11 @@ mt7531_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
phydev = dp->slave->phydev;
return mt7531_rgmii_setup(priv, port, interface, phydev);
case PHY_INTERFACE_MODE_SGMII:
- return mt7531_sgmii_setup_mode_an(priv, port, interface);
case PHY_INTERFACE_MODE_NA:
case PHY_INTERFACE_MODE_1000BASEX:
case PHY_INTERFACE_MODE_2500BASEX:
- return mt7531_sgmii_setup_mode_force(priv, port, interface);
+ /* handled in SGMII PCS driver */
+ return 0;
default:
return -EINVAL;
}
@@ -2740,11 +2624,11 @@ mt753x_phylink_mac_select_pcs(struct dsa_switch *ds, int port,
switch (interface) {
case PHY_INTERFACE_MODE_TRGMII:
+ return &priv->pcs[port].pcs;
case PHY_INTERFACE_MODE_SGMII:
case PHY_INTERFACE_MODE_1000BASEX:
case PHY_INTERFACE_MODE_2500BASEX:
- return &priv->pcs[port].pcs;
-
+ return priv->ports[port].sgmii_pcs;
default:
return NULL;
}
@@ -2982,86 +2866,6 @@ static void mt7530_pcs_get_state(struct phylink_pcs *pcs,
state->pause |= MLO_PAUSE_TX;
}
-static int
-mt7531_sgmii_pcs_get_state_an(struct mt7530_priv *priv, int port,
- struct phylink_link_state *state)
-{
- u32 status, val;
- u16 config_reg;
-
- status = mt7530_read(priv, MT7531_PCS_CONTROL_1(port));
- state->link = !!(status & MT7531_SGMII_LINK_STATUS);
- state->an_complete = !!(status & MT7531_SGMII_AN_COMPLETE);
- if (state->interface == PHY_INTERFACE_MODE_SGMII &&
- (status & MT7531_SGMII_AN_ENABLE)) {
- val = mt7530_read(priv, MT7531_PCS_SPEED_ABILITY(port));
- config_reg = val >> 16;
-
- switch (config_reg & LPA_SGMII_SPD_MASK) {
- case LPA_SGMII_1000:
- state->speed = SPEED_1000;
- break;
- case LPA_SGMII_100:
- state->speed = SPEED_100;
- break;
- case LPA_SGMII_10:
- state->speed = SPEED_10;
- break;
- default:
- dev_err(priv->dev, "invalid sgmii PHY speed\n");
- state->link = false;
- return -EINVAL;
- }
-
- if (config_reg & LPA_SGMII_FULL_DUPLEX)
- state->duplex = DUPLEX_FULL;
- else
- state->duplex = DUPLEX_HALF;
- }
-
- return 0;
-}
-
-static void
-mt7531_sgmii_pcs_get_state_inband(struct mt7530_priv *priv, int port,
- struct phylink_link_state *state)
-{
- unsigned int val;
-
- val = mt7530_read(priv, MT7531_PCS_CONTROL_1(port));
- state->link = !!(val & MT7531_SGMII_LINK_STATUS);
- if (!state->link)
- return;
-
- state->an_complete = state->link;
-
- if (state->interface == PHY_INTERFACE_MODE_2500BASEX)
- state->speed = SPEED_2500;
- else
- state->speed = SPEED_1000;
-
- state->duplex = DUPLEX_FULL;
- state->pause = MLO_PAUSE_NONE;
-}
-
-static void mt7531_pcs_get_state(struct phylink_pcs *pcs,
- struct phylink_link_state *state)
-{
- struct mt7530_priv *priv = pcs_to_mt753x_pcs(pcs)->priv;
- int port = pcs_to_mt753x_pcs(pcs)->port;
-
- if (state->interface == PHY_INTERFACE_MODE_SGMII) {
- mt7531_sgmii_pcs_get_state_an(priv, port, state);
- return;
- } else if ((state->interface == PHY_INTERFACE_MODE_1000BASEX) ||
- (state->interface == PHY_INTERFACE_MODE_2500BASEX)) {
- mt7531_sgmii_pcs_get_state_inband(priv, port, state);
- return;
- }
-
- state->link = false;
-}
-
static int mt753x_pcs_config(struct phylink_pcs *pcs, unsigned int mode,
phy_interface_t interface,
const unsigned long *advertising,
@@ -3081,18 +2885,57 @@ static const struct phylink_pcs_ops mt7530_pcs_ops = {
.pcs_an_restart = mt7530_pcs_an_restart,
};
-static const struct phylink_pcs_ops mt7531_pcs_ops = {
- .pcs_validate = mt753x_pcs_validate,
- .pcs_get_state = mt7531_pcs_get_state,
- .pcs_config = mt753x_pcs_config,
- .pcs_an_restart = mt7531_pcs_an_restart,
- .pcs_link_up = mt7531_pcs_link_up,
+static int mt7530_regmap_read(void *context, unsigned int reg, unsigned int *val)
+{
+ struct mt7530_priv *priv = context;
+
+ *val = mt7530_read(priv, reg);
+ return 0;
+};
+
+static int mt7530_regmap_write(void *context, unsigned int reg, unsigned int val)
+{
+ struct mt7530_priv *priv = context;
+
+ mt7530_write(priv, reg, val);
+ return 0;
+};
+
+static int mt7530_regmap_update_bits(void *context, unsigned int reg,
+ unsigned int mask, unsigned int val)
+{
+ struct mt7530_priv *priv = context;
+
+ mt7530_rmw(priv, reg, mask, val);
+ return 0;
+};
+
+static const struct regmap_bus mt7531_regmap_bus = {
+ .reg_write = mt7530_regmap_write,
+ .reg_read = mt7530_regmap_read,
+ .reg_update_bits = mt7530_regmap_update_bits,
+};
+
+#define MT7531_PCS_REGMAP_CONFIG(_name, _reg_base) \
+ { \
+ .name = _name, \
+ .reg_bits = 16, \
+ .val_bits = 32, \
+ .reg_stride = 4, \
+ .reg_base = _reg_base, \
+ .max_register = 0x17c, \
+ }
+
+static const struct regmap_config mt7531_pcs_config[] = {
+ MT7531_PCS_REGMAP_CONFIG("port5", MT7531_SGMII_REG_BASE(5)),
+ MT7531_PCS_REGMAP_CONFIG("port6", MT7531_SGMII_REG_BASE(6)),
};
static int
mt753x_setup(struct dsa_switch *ds)
{
struct mt7530_priv *priv = ds->priv;
+ struct regmap *regmap;
int i, ret;
/* Initialise the PCS devices */
@@ -3100,8 +2943,6 @@ mt753x_setup(struct dsa_switch *ds)
priv->pcs[i].pcs.ops = priv->info->pcs_ops;
priv->pcs[i].priv = priv;
priv->pcs[i].port = i;
- if (mt753x_is_mac_port(i))
- priv->pcs[i].pcs.poll = 1;
}
ret = priv->info->sw_setup(ds);
@@ -3116,6 +2957,16 @@ mt753x_setup(struct dsa_switch *ds)
if (ret && priv->irq)
mt7530_free_irq_common(priv);
+ if (priv->id == ID_MT7531)
+ for (i = 0; i < 2; i++) {
+ regmap = devm_regmap_init(ds->dev,
+ &mt7531_regmap_bus, priv,
+ &mt7531_pcs_config[i]);
+ priv->ports[5 + i].sgmii_pcs =
+ mtk_pcs_lynxi_create(ds->dev, regmap,
+ MT7531_PHYA_CTRL_SIGNAL3, 0);
+ }
+
return ret;
}
@@ -3211,7 +3062,7 @@ static const struct mt753x_info mt753x_table[] = {
},
[ID_MT7531] = {
.id = ID_MT7531,
- .pcs_ops = &mt7531_pcs_ops,
+ .pcs_ops = &mt7530_pcs_ops,
.sw_setup = mt7531_setup,
.phy_read_c22 = mt7531_ind_c22_phy_read,
.phy_write_c22 = mt7531_ind_c22_phy_write,
@@ -3321,7 +3172,7 @@ static void
mt7530_remove(struct mdio_device *mdiodev)
{
struct mt7530_priv *priv = dev_get_drvdata(&mdiodev->dev);
- int ret = 0;
+ int ret = 0, i;
if (!priv)
return;
@@ -3340,6 +3191,10 @@ mt7530_remove(struct mdio_device *mdiodev)
mt7530_free_irq(priv);
dsa_unregister_switch(priv->ds);
+
+ for (i = 0; i < 2; ++i)
+ mtk_pcs_lynxi_destroy(priv->ports[5 + i].sgmii_pcs);
+
mutex_destroy(&priv->reg_mutex);
}
diff --git a/drivers/net/dsa/mt7530.h b/drivers/net/dsa/mt7530.h
index 6b2fc6290ea8..c5d29f3fc1d8 100644
--- a/drivers/net/dsa/mt7530.h
+++ b/drivers/net/dsa/mt7530.h
@@ -364,47 +364,8 @@ enum mt7530_vlan_port_acc_frm {
CCR_TX_OCT_CNT_BAD)
/* MT7531 SGMII register group */
-#define MT7531_SGMII_REG_BASE 0x5000
-#define MT7531_SGMII_REG(p, r) (MT7531_SGMII_REG_BASE + \
- ((p) - 5) * 0x1000 + (r))
-
-/* Register forSGMII PCS_CONTROL_1 */
-#define MT7531_PCS_CONTROL_1(p) MT7531_SGMII_REG(p, 0x00)
-#define MT7531_SGMII_LINK_STATUS BIT(18)
-#define MT7531_SGMII_AN_ENABLE BIT(12)
-#define MT7531_SGMII_AN_RESTART BIT(9)
-#define MT7531_SGMII_AN_COMPLETE BIT(21)
-
-/* Register for SGMII PCS_SPPED_ABILITY */
-#define MT7531_PCS_SPEED_ABILITY(p) MT7531_SGMII_REG(p, 0x08)
-#define MT7531_SGMII_TX_CONFIG_MASK GENMASK(15, 0)
-#define MT7531_SGMII_TX_CONFIG BIT(0)
-
-/* Register for SGMII_MODE */
-#define MT7531_SGMII_MODE(p) MT7531_SGMII_REG(p, 0x20)
-#define MT7531_SGMII_REMOTE_FAULT_DIS BIT(8)
-#define MT7531_SGMII_IF_MODE_MASK GENMASK(5, 1)
-#define MT7531_SGMII_FORCE_DUPLEX BIT(4)
-#define MT7531_SGMII_FORCE_SPEED_MASK GENMASK(3, 2)
-#define MT7531_SGMII_FORCE_SPEED_1000 BIT(3)
-#define MT7531_SGMII_FORCE_SPEED_100 BIT(2)
-#define MT7531_SGMII_FORCE_SPEED_10 0
-#define MT7531_SGMII_SPEED_DUPLEX_AN BIT(1)
-
-enum mt7531_sgmii_force_duplex {
- MT7531_SGMII_FORCE_FULL_DUPLEX = 0,
- MT7531_SGMII_FORCE_HALF_DUPLEX = 0x10,
-};
-
-/* Fields of QPHY_PWR_STATE_CTRL */
-#define MT7531_QPHY_PWR_STATE_CTRL(p) MT7531_SGMII_REG(p, 0xe8)
-#define MT7531_SGMII_PHYA_PWD BIT(4)
-
-/* Values of SGMII SPEED */
-#define MT7531_PHYA_CTRL_SIGNAL3(p) MT7531_SGMII_REG(p, 0x128)
-#define MT7531_RG_TPHY_SPEED_MASK (BIT(2) | BIT(3))
-#define MT7531_RG_TPHY_SPEED_1_25G 0x0
-#define MT7531_RG_TPHY_SPEED_3_125G BIT(2)
+#define MT7531_SGMII_REG_BASE(p) (0x5000 + ((p) - 5) * 0x1000)
+#define MT7531_PHYA_CTRL_SIGNAL3 0x128
/* Register for system reset */
#define MT7530_SYS_CTRL 0x7000
@@ -703,13 +664,13 @@ struct mt7530_fdb {
* @pm: The matrix used to show all connections with the port.
* @pvid: The VLAN specified is to be considered a PVID at ingress. Any
* untagged frames will be assigned to the related VLAN.
- * @vlan_filtering: The flags indicating whether the port that can recognize
- * VLAN-tagged frames.
+ * @sgmii_pcs: Pointer to PCS instance for SerDes ports
*/
struct mt7530_port {
bool enable;
u32 pm;
u16 pvid;
+ struct phylink_pcs *sgmii_pcs;
};
/* Port 5 interface select definitions */
--
2.39.1
More information about the linux-arm-kernel
mailing list