[PATCH v9 6/7] arm64: dts: ti: k3-j721e-sk: Add TPS6594 family PMICs

[Kumar, Udit]

On 12/5/2023 8:46 PM, Nishanth Menon wrote:
> On 15:04-20231205, Neha Malcom Francis wrote:
>> This patch adds support for TPS6594 PMIC family on wakeup I2C0 bus.
>> These devices provide regulators (bucks and LDOs), but also GPIOs, a
>> RTC, a watchdog, an ESM (Error Signal Monitor) which monitors the SoC
>> error output signal, and a PFSM (Pre-configurable Finite State Machine)
>> which manages the operational modes of the PMIC.
>>
>> Signed-off-by: Neha Malcom Francis <n-francis at ti.com>
>> ---
>>   arch/arm64/boot/dts/ti/k3-j721e-sk.dts | 158 +++++++++++++++++++++++++
>>   1 file changed, 158 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/ti/k3-j721e-sk.dts b/arch/arm64/boot/dts/ti/k3-j721e-sk.dts
>> index 42fe8eee9ec8..e600825f7e78 100644
>> --- a/arch/arm64/boot/dts/ti/k3-j721e-sk.dts
>> +++ b/arch/arm64/boot/dts/ti/k3-j721e-sk.dts
>> @@ -459,6 +459,13 @@ J721E_IOPAD(0x234, PIN_INPUT, 7) /* (U3) EXT_REFCLK1.GPIO1_12 */
>>   };
>>   
>>   &wkup_pmx0 {
>> +	pmic_irq_pins_default: pmic-irq-default-pins {
>> +		bootph-pre-ram;
>> +		pinctrl-single,pins = <
>> +			J721E_WKUP_IOPAD(0x0cc, PIN_INPUT, 7) /* (G28) WKUP_GPIO0_7 */
>> +		>;
>> +	};
>> +
>>   	mcu_cpsw_pins_default: mcu-cpsw-default-pins {
>>   		pinctrl-single,pins = <
>>   			J721E_WKUP_IOPAD(0x84, PIN_INPUT, 0) /* (B24) MCU_RGMII1_RD0 */
>> @@ -560,6 +567,157 @@ eeprom at 51 {
>>   		compatible = "atmel,24c512";
>>   		reg = <0x51>;
>>   	};
>> +
>> +	tps659413: pmic at 48 {
>> +		bootph-pre-ram;
> only for the leaf nodes. See
> https://libera.irclog.whitequark.org/armlinux/2023-10-19


AFAIK, please correct me, u-boot still needs in all nodes ?

>
>> +		compatible = "ti,tps6594-q1";
>> +		reg = <0x48>;
>> +		system-power-controller;
>> +		pinctrl-names = "default";
>> +		pinctrl-0 = <&pmic_irq_pins_default>;
>> +		interrupt-parent = <&wkup_gpio0>;
>> +		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
>> +		ti,primary-pmic;
>> +
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		buck123-supply = <&vsys_3v3>;
>> +		buck4-supply = <&vsys_3v3>;
>> +		buck5-supply = <&vsys_3v3>;
>> +		ldo1-supply = <&vsys_3v3>;
>> +		ldo2-supply = <&vsys_3v3>;
>> +		ldo3-supply = <&vsys_3v3>;
>> +		ldo4-supply = <&vsys_3v3>;
>> +
>> +		regulators {
>> +			bootph-pre-ram;
>> +			bucka123: buck123 {
>> +				bootph-pre-ram;
>> +				regulator-name = "vdd_cpu_avs";
>> +				regulator-min-microvolt = <600000>;
>> +				regulator-max-microvolt = <900000>;
>> +				regulator-boot-on;
>> +				regulator-always-on;
>> +			};
>> +
>> +			bucka4: buck4 {
>> +				regulator-name = "vdd_mcu_0v85";
>> +				regulator-min-microvolt = <850000>;
>> +				regulator-max-microvolt = <850000>;
>> +				regulator-boot-on;
>> +				regulator-always-on;
>> +			};
>> +
>> +			bucka5: buck5 {
>> +				regulator-name = "vdd_phyio_1v8";
>> +				regulator-min-microvolt = <1800000>;
>> +				regulator-max-microvolt = <1800000>;
>> +				regulator-boot-on;
>> +				regulator-always-on;
>> +			};
>> +
>> +			ldoa1: ldo1 {
>> +				regulator-name = "vdd1_lpddr4_1v8";
>> +				regulator-min-microvolt = <1800000>;
>> +				regulator-max-microvolt = <1800000>;
>> +				regulator-boot-on;
>> +				regulator-always-on;
>> +			};
>> +
>> +			ldoa2: ldo2 {
>> +				regulator-name = "vdd_mcuio_1v8";
>> +				regulator-min-microvolt = <1800000>;
>> +				regulator-max-microvolt = <1800000>;
>> +				regulator-boot-on;
>> +				regulator-always-on;
>> +			};
>> +
>> +			ldoa3: ldo3 {
>> +				regulator-name = "vdda_dll_0v8";
>> +				regulator-min-microvolt = <800000>;
>> +				regulator-max-microvolt = <800000>;
>> +				regulator-boot-on;
>> +				regulator-always-on;
>> +			};
>> +
>> +			ldoa4: ldo4 {
>> +				regulator-name = "vda_mcu_1v8";
>> +				regulator-min-microvolt = <1800000>;
>> +				regulator-max-microvolt = <1800000>;
>> +				regulator-boot-on;
>> +				regulator-always-on;
>> +			};
>> +		};
>> +	};
>> +
>> +	tps659411: pmic at 4c {
>> +		compatible = "ti,tps6594-q1";
>> +		reg = <0x4c>;
>> +		system-power-controller;
>> +		interrupt-parent = <&wkup_gpio0>;
>> +		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
>> +
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		buck1234-supply = <&vsys_3v3>;
>> +		buck5-supply = <&vsys_3v3>;
>> +		ldo1-supply = <&vsys_3v3>;
>> +		ldo2-supply = <&vsys_3v3>;
>> +		ldo3-supply = <&vsys_3v3>;
>> +		ldo4-supply = <&vsys_3v3>;
>> +
>> +		regulators {
>> +			buckb1234: buck1234 {
>> +				regulator-name = "vdd_core_0v8";
>> +				regulator-min-microvolt = <800000>;
>> +				regulator-max-microvolt = <800000>;
>> +				regulator-boot-on;
>> +				regulator-always-on;
>> +			};
>> +
>> +			buckb5: buck5 {
>> +				regulator-name = "vdd_ram_0v85";
>> +				regulator-min-microvolt = <850000>;
>> +				regulator-max-microvolt = <850000>;
>> +				regulator-boot-on;
>> +				regulator-always-on;
>> +			};
>> +
>> +			ldob1: ldo1 {
>> +				regulator-name = "vdd_sd_dv";
>> +				regulator-min-microvolt = <1800000>;
>> +				regulator-max-microvolt = <3300000>;
>> +				regulator-boot-on;
>> +				regulator-always-on;
>> +			};
>> +
>> +			ldob2: ldo2 {
>> +				regulator-name = "vdd_usb_3v3";
>> +				regulator-min-microvolt = <3300000>;
>> +				regulator-max-microvolt = <3300000>;
>> +				regulator-boot-on;
>> +				regulator-always-on;
>> +			};
>> +
>> +			ldob3: ldo3 {
>> +				regulator-name = "vdd_io_1v8";
>> +				regulator-min-microvolt = <1800000>;
>> +				regulator-max-microvolt = <1800000>;
>> +				regulator-boot-on;
>> +				regulator-always-on;
>> +			};
>> +
>> +			ldob4: ldo4 {
>> +				regulator-name = "vda_pll_1v8";
>> +				regulator-min-microvolt = <1800000>;
>> +				regulator-max-microvolt = <1800000>;
>> +				regulator-boot-on;
>> +				regulator-always-on;
>> +			};
>> +		};
>> +	};
>>   };
>>   
>>   &mcu_uart0 {
>> -- 
>> 2.34.1
>>