[PATCHv1 3/8] ARM: dts: at91: sam9x60: Add flexcom definitions

[Claudiu.Beznea at microchip.com]

On 31.10.2022 05:36, Durai Manickam KR wrote:
> Add the flexcom definitions to the SoC specifc DTSI file.
> 
> Signed-off-by: Durai Manickam KR <durai.manickamkr at microchip.com>
> Signed-off-by: Hari Prasath <Hari.PrasathGE at microchip.com>
> Signed-off-by: Manikandan M <manikandan.m at microchip.com>
> ---
>  arch/arm/boot/dts/sam9x60.dtsi | 52 ++++++++++++++++++++++++++++++++--
>  1 file changed, 50 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/sam9x60.dtsi b/arch/arm/boot/dts/sam9x60.dtsi
> index ef07d281a3db..fd4f5d43f7bb 100644
> --- a/arch/arm/boot/dts/sam9x60.dtsi
> +++ b/arch/arm/boot/dts/sam9x60.dtsi
> @@ -170,6 +170,16 @@ flx4: flexcom at f0000000 {
>  				#size-cells = <1>;
>  				ranges = <0x0 0xf0000000 0x800>;
>  				status = "disabled";
> +
> +				spi4: spi at 400 {
> +					compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
> +					reg = <0x400 0x200>;
> +					interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
> +					clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
> +					clock-names = "spi_clk";
> +					atmel,fifo-size = <16>;
> +					status = "disabled";
> +				};
>  			};
>  
>  			flx5: flexcom at f0004000 {
> @@ -180,6 +190,26 @@ flx5: flexcom at f0004000 {
>  				#size-cells = <1>;
>  				ranges = <0x0 0xf0004000 0x800>;
>  				status = "disabled";
> +
> +				uart5: serial at 200 {
> +					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> +					reg = <0x200 0x200>;
> +					interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
> +					dmas = <&dma0
> +						(AT91_XDMAC_DT_MEM_IF(0) |
> +						 AT91_XDMAC_DT_PER_IF(1) |
> +						 AT91_XDMAC_DT_PERID(10))>,
> +						<&dma0
> +						(AT91_XDMAC_DT_MEM_IF(0) |
> +						 AT91_XDMAC_DT_PER_IF(1) |
> +						 AT91_XDMAC_DT_PERID(11))>;
> +					dma-names = "tx", "rx";
> +					clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
> +					clock-names = "usart";
> +					atmel,use-dma-rx;
> +					atmel,use-dma-tx;
> +					status = "disabled";
> +				};
>  			};
>  
>  			dma0: dma-controller at f0008000 {
> @@ -390,6 +420,15 @@ flx6: flexcom at f8010000 {
>  				#size-cells = <1>;
>  				ranges = <0x0 0xf8010000 0x800>;
>  				status = "disabled";
> +
> +				i2c6: i2c at 600 {
> +					compatible = "microchip,sam9x60-i2c";
> +					reg = <0x600 0x200>;
> +					interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
> +					clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
> +					atmel,fifo-size = <16>;
> +					status = "disabled";
> +				};
>  			};
>  
>  			flx7: flexcom at f8014000 {
> @@ -416,10 +455,19 @@ flx0: flexcom at f801c000 {
>  				compatible = "atmel,sama5d2-flexcom";
>  				reg = <0xf801c000 0x200>;
>  				clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
> -				#address-cells = <1>;
> -				#size-cells = <1>;

As far as I can tell you will get compilation warning if removing these
properties.

>  				ranges = <0x0 0xf801c000 0x800>;
>  				status = "disabled";
> +
> +				i2c0: i2c at 600 {
> +					compatible = "microchip,sam9x60-i2c";
> +					reg = <0x600 0x200>;
> +					interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +					clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
> +					atmel,fifo-size = <16>;
> +					status = "disabled";
> +				};
>  			};
>  
>  			flx1: flexcom at f8020000 {