[PATCHv1 2/8] ARM: dts: at91: sam9x60: remove flexcom definitions

[Claudiu.Beznea at microchip.com]

On 31.10.2022 05:36, Durai Manickam KR wrote:
> Remove the flexcom definitions in the board specific DTS file of sam9x60ek.
> 
> Signed-off-by: Durai Manickam KR <durai.manickamkr at microchip.com>
> ---
>  arch/arm/boot/dts/at91-sam9x60ek.dts | 35 +---------------------------
>  1 file changed, 1 insertion(+), 34 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/at91-sam9x60ek.dts b/arch/arm/boot/dts/at91-sam9x60ek.dts
> index 265978514dcf..9d9e50c77794 100644
> --- a/arch/arm/boot/dts/at91-sam9x60ek.dts
> +++ b/arch/arm/boot/dts/at91-sam9x60ek.dts
> @@ -211,15 +211,10 @@ &flx0 {
>  	status = "okay";
>  
>  	i2c0: i2c at 600 {
> -		compatible = "microchip,sam9x60-i2c";
> -		reg = <0x600 0x200>;
> -		interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
>  		#address-cells = <1>;
>  		#size-cells = <0>;
> -		clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
>  		pinctrl-names = "default";
>  		pinctrl-0 = <&pinctrl_flx0_default>;
> -		atmel,fifo-size = <16>;
>  		i2c-analog-filter;
>  		i2c-digital-filter;
>  		i2c-digital-filter-width-ns = <35>;
> @@ -239,16 +234,8 @@ &flx4 {
>  	status = "disabled";
>  
>  	spi4: spi at 400 {
> -		compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
> -		reg = <0x400 0x200>;
> -		interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
> -		clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
> -		clock-names = "spi_clk";
>  		pinctrl-names = "default";
>  		pinctrl-0 = <&pinctrl_flx4_default>;
> -		atmel,fifo-size = <16>;

As mention in the previous version, this starting here

> -		#address-cells = <1>;
> -		#size-cells = <0>;

ending here is not moved to dtsi but was just deleted. Please include it in
another patch.

Also, you will have to merge this patch with the next to have the
components removed here still working in this patch.

>  		status = "disabled";
>  	};
>  };
> @@ -258,23 +245,8 @@ &flx5 {
>  	status = "okay";
>  
>  	uart5: serial at 200 {
> -		compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
> -		reg = <0x200 0x200>;
> -		atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
> -		interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
> -		dmas = <&dma0
> -			(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> -			 AT91_XDMAC_DT_PERID(10))>,
> -		       <&dma0
> -			(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> -			 AT91_XDMAC_DT_PERID(11))>;
> -		dma-names = "tx", "rx";
> -		clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
> -		clock-names = "usart";
> -		pinctrl-0 = <&pinctrl_flx5_default>;
>  		pinctrl-names = "default";
> -		atmel,use-dma-rx;
> -		atmel,use-dma-tx;
> +		pinctrl-0 = <&pinctrl_flx5_default>;
>  		status = "okay";
>  	};
>  };
> @@ -284,15 +256,10 @@ &flx6 {
>  	status = "okay";
>  
>  	i2c6: i2c at 600 {
> -		compatible = "microchip,sam9x60-i2c";
> -		reg = <0x600 0x200>;
> -		interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
>  		#address-cells = <1>;
>  		#size-cells = <0>;
> -		clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
>  		pinctrl-names = "default";
>  		pinctrl-0 = <&pinctrl_flx6_default>;
> -		atmel,fifo-size = <16>;
>  		i2c-analog-filter;
>  		i2c-digital-filter;
>  		i2c-digital-filter-width-ns = <35>;