[PATCH 0/6] Support second Image Signal Processor on rk3399
sebastian.fricke at posteo.net
Fri Feb 5 01:43:35 EST 2021
On 03.02.2021 20:54, Heiko Stübner wrote:
>Am Mittwoch, 3. Februar 2021, 19:14:22 CET schrieb Sebastian Fricke:
>> Hey Heiko,
>> I have tested your patch set on my nanoPC-T4, here is a complete log
>> - relevant kernel log entries
>> - system information
>> - media ctl output
>> - sysfs entry information
>> Additionally, to your patchset I have applied the following patches:
>> And just to not cause confusion the `media_dev` entries come from this
>> unmerged series:
>> I have actually been able to stream with both of my cameras at the same
>> time using the libcamera cam command.
>> I would like to thank you a lot for making this possible.
>Thanks for testing a dual camera setup. On my board I could only test
>the second ISP. And really glad it works for you tool :-) .
>Out of curiosity, do you also see that green tint in the images the cameras
Yes, I do. Actually, I currently have two forms of a green tint, on my
OV13850 everything is quite dark and greenish, which is caused by the
missing 3A algorithms. On my OV4689, I have big patches of the image
with bright green color and flickering, I investigated if this is
connected to the 2nd ISP instance, but that doesn't seem to be the case
as I have the same results when I switch the CSI ports of the cameras.
I have found another issue, while testing I discovered following
When I start the system with an HDMI monitor connected, then the camera
on the 2nd port doesn't work. This is probably because the RX/TX is
reserved as a TX.
But it made me wonder because if the system has an RX, a TX, and
an RX/TX, why isn't the pure TX used by the monitor and the
cameras take RX and RX/TX?
Or do you think that this is maybe a malfunction of this patch?
>> If you like to you can add:
>> Tested-by: Sebastian Fricke <sebastian.fricke at posteo.net>
>> On 02.02.2021 15:56, Heiko Stuebner wrote:
>> >The rk3399 has two ISPs and right now only the first one is usable.
>> >The second ISP is connected to the TXRX dphy on the soc.
>> >The phy of ISP1 is only accessible through the DSI controller's
>> >io-memory, so this series adds support for simply using the dsi
>> >controller is a phy if needed.
>> >That solution is needed at least on rk3399 and rk3288 but no-one
>> >has looked at camera support on rk3288 at all, so right now
>> >only implement the rk3399 specifics.
>> >Heiko Stuebner (6):
>> > drm/rockchip: dsi: add own additional pclk handling
>> > dt-bindings: display: rockchip-dsi: add optional #phy-cells property
>> > drm/rockchip: dsi: add ability to work as a phy instead of full dsi
>> > arm64: dts: rockchip: add #phy-cells to mipi-dsi1
>> > arm64: dts: rockchip: add cif clk-control pinctrl for rk3399
>> > arm64: dts: rockchip: add isp1 node on rk3399
>> > .../display/rockchip/dw_mipi_dsi_rockchip.txt | 1 +
>> > arch/arm64/boot/dts/rockchip/rk3399.dtsi | 39 ++
>> > drivers/gpu/drm/rockchip/Kconfig | 2 +
>> > .../gpu/drm/rockchip/dw-mipi-dsi-rockchip.c | 342 ++++++++++++++++++
>> > 4 files changed, 384 insertions(+)
More information about the linux-arm-kernel