[PATCH v1 1/3] dt-bindings: PCI: imx6: convert the imx pcie controller to dtschema
Richard Zhu
hongxing.zhu at nxp.com
Mon Aug 23 23:04:19 PDT 2021
> -----Original Message-----
> From: Rob Herring <robh at kernel.org>
> Sent: Tuesday, August 24, 2021 2:34 AM
> To: Richard Zhu <hongxing.zhu at nxp.com>
> Cc: l.stach at pengutronix.de; galak at kernel.crashing.org;
> shawnguo at kernel.org; devicetree at vger.kernel.org;
> linux-arm-kernel at lists.infradead.org; linux-kernel at vger.kernel.org;
> dl-linux-imx <linux-imx at nxp.com>; kernel at pengutronix.de
> Subject: Re: [PATCH v1 1/3] dt-bindings: PCI: imx6: convert the imx pcie
> controller to dtschema
>
> On Thu, Aug 19, 2021 at 03:14:06PM +0800, Richard Zhu wrote:
> > Convert the fsl,imx6q-pcie.txt into a schema.
> > - the ranges should be aligned to $ref: /schemas/pci/pci-bus.yaml#
> > - only one propert is allowed in the compatible string, remove
> > "snps,dw-pcie".
>
> Didn't I already see a v1?
[Richard Zhu] I assume that the RFC version as the v0, not formal v1.
Would pay attention to that.
>
> >
> > Signed-off-by: Richard Zhu <hongxing.zhu at nxp.com>
> > ---
> > .../bindings/pci/fsl,imx6q-pcie.txt | 100 ---------
> > .../bindings/pci/fsl,imx6q-pcie.yaml | 207
> ++++++++++++++++++
> > MAINTAINERS | 2 +-
> > 3 files changed, 208 insertions(+), 101 deletions(-) delete mode
> > 100644 Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
> > create mode 100644
> > Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
> >
> > diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
> > b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
> > deleted file mode 100644
> > index d8971ab99274..000000000000
> > --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
> > +++ /dev/null
> > @@ -1,100 +0,0 @@
> > -* Freescale i.MX6 PCIe interface
> > -
> > -This PCIe host controller is based on the Synopsys DesignWare PCIe IP
> > -and thus inherits all the common properties defined in designware-pcie.txt.
> > -
> > -Required properties:
> > -- compatible:
> > - - "fsl,imx6q-pcie"
> > - - "fsl,imx6sx-pcie",
> > - - "fsl,imx6qp-pcie"
> > - - "fsl,imx7d-pcie"
> > - - "fsl,imx8mq-pcie"
> > -- reg: base address and length of the PCIe controller
> > -- interrupts: A list of interrupt outputs of the controller. Must
> > contain an
> > - entry for each entry in the interrupt-names property.
> > -- interrupt-names: Must include the following entries:
> > - - "msi": The interrupt that is asserted when an MSI is received
> > -- clock-names: Must include the following additional entries:
> > - - "pcie_phy"
> > -
> > -Optional properties:
> > -- fsl,tx-deemph-gen1: Gen1 De-emphasis value. Default: 0
> > -- fsl,tx-deemph-gen2-3p5db: Gen2 (3.5db) De-emphasis value. Default:
> > 0
> > -- fsl,tx-deemph-gen2-6db: Gen2 (6db) De-emphasis value. Default: 20
> > -- fsl,tx-swing-full: Gen2 TX SWING FULL value. Default: 127
> > -- fsl,tx-swing-low: TX launch amplitude swing_low value. Default: 127
> > -- fsl,max-link-speed: Specify PCI gen for link capability. Must be
> > '2' for
> > - gen2, otherwise will default to gen1. Note that the IMX6 LVDS clock
> > outputs
> > - do not meet gen2 jitter requirements and thus for gen2 capability a
> > gen2
> > - compliant clock generator should be used and configured.
> > -- reset-gpio: Should specify the GPIO for controlling the PCI bus
> > device reset
> > - signal. It's not polarity aware and defaults to active-low reset
> > sequence
> > - (L=reset state, H=operation state).
> > -- reset-gpio-active-high: If present then the reset sequence using
> > the GPIO
> > - specified in the "reset-gpio" property is reversed (H=reset state,
> > - L=operation state).
> > -- vpcie-supply: Should specify the regulator in charge of PCIe port power.
> > - The regulator will be enabled when initializing the PCIe host and
> > - disabled either as part of the init process or when shutting down
> > the
> > - host.
> > -- vph-supply: Should specify the regulator in charge of VPH one of
> > the three
> > - PCIe PHY powers. This regulator can be supplied by both 1.8v and
> > 3.3v voltage
> > - supplies.
> > -
> > -Additional required properties for imx6sx-pcie:
> > -- clock names: Must include the following additional entries:
> > - - "pcie_inbound_axi"
> > -- power-domains: Must be set to phandles pointing to the DISPLAY and
> > - PCIE_PHY power domains
> > -- power-domain-names: Must be "pcie", "pcie_phy"
> > -
> > -Additional required properties for imx7d-pcie and imx8mq-pcie:
> > -- power-domains: Must be set to a phandle pointing to PCIE_PHY power
> > domain
> > -- resets: Must contain phandles to PCIe-related reset lines exposed
> > by SRC
> > - IP block
> > -- reset-names: Must contain the following entries:
> > - - "pciephy"
> > - - "apps"
> > - - "turnoff"
> > -- fsl,imx7d-pcie-phy: A phandle to an fsl,imx7d-pcie-phy node.
> > -
> > -Additional required properties for imx8mq-pcie:
> > -- clock-names: Must include the following additional entries:
> > - - "pcie_aux"
> > -
> > -Example:
> > -
> > - pcie at 01000000 {
> > - compatible = "fsl,imx6q-pcie", "snps,dw-pcie";
> > - reg = <0x01ffc000 0x04000>,
> > - <0x01f00000 0x80000>;
> > - reg-names = "dbi", "config";
> > - #address-cells = <3>;
> > - #size-cells = <2>;
> > - device_type = "pci";
> > - ranges = <0x00000800 0 0x01f00000 0x01f00000 0 0x00080000
> > - 0x81000000 0 0 0x01f80000 0 0x00010000
> > - 0x82000000 0 0x01000000 0x01000000 0 0x00f00000>;
> > - num-lanes = <1>;
> > - interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
> > - interrupt-names = "msi";
> > - #interrupt-cells = <1>;
> > - interrupt-map-mask = <0 0 0 0x7>;
> > - interrupt-map = <0 0 0 1 &intc GIC_SPI 123
> IRQ_TYPE_LEVEL_HIGH>,
> > - <0 0 0 2 &intc GIC_SPI 122
> IRQ_TYPE_LEVEL_HIGH>,
> > - <0 0 0 3 &intc GIC_SPI 121
> IRQ_TYPE_LEVEL_HIGH>,
> > - <0 0 0 4 &intc GIC_SPI 120
> IRQ_TYPE_LEVEL_HIGH>;
> > - clocks = <&clks 144>, <&clks 206>, <&clks 189>;
> > - clock-names = "pcie", "pcie_bus", "pcie_phy";
> > - };
> > -
> > -* Freescale i.MX7d PCIe PHY
> > -
> > -This is the PHY associated with the IMX7d PCIe controller. It's used
> > by the -PCI-e controller via the fsl,imx7d-pcie-phy phandle.
> > -
> > -Required properties:
> > -- compatible:
> > - - "fsl,imx7d-pcie-phy"
> > -- reg: base address and length of the PCIe PHY controller diff --git
> > a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
> > b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
> > new file mode 100644
> > index 000000000000..3503ce3de05d
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
> > @@ -0,0 +1,207 @@
> > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) %YAML 1.2
> > +---
> > +$id:
> > +https://eur01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fdevi
> >
> +cetree.org%2Fschemas%2Fpci%2Ffsl%2Cimx6q-pcie.yaml%23&data=0
> 4%7C0
> >
> +1%7Chongxing.zhu%40nxp.com%7Ca0e50943284145edfdc808d966649a08
> %7C686ea
> >
> +1d3bc2b4c6fa92cd99c5c301635%7C0%7C1%7C637653404543147546%7C
> Unknown%7C
> >
> +TWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwi
> LCJXV
> >
> +CI6Mn0%3D%7C3000&sdata=mW%2FTR8dffuxQDk%2Fm1eiUd8IIRBjE
> mJMhkxQZPo
> > +GYfHM%3D&reserved=0
> > +$schema:
> > +https://eur01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fdevi
> >
> +cetree.org%2Fmeta-schemas%2Fcore.yaml%23&data=04%7C01%7Cho
> ngxing.
> >
> +zhu%40nxp.com%7Ca0e50943284145edfdc808d966649a08%7C686ea1d3b
> c2b4c6fa9
> >
> +2cd99c5c301635%7C0%7C1%7C637653404543147546%7CUnknown%7CT
> WFpbGZsb3d8e
> >
> +yJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3
> D%7C3
> >
> +000&sdata=Gh1dUyXO80b2aKvWKe0Q2GIN4w%2BCit1oj06AvToamuE
> %3D&re
> > +served=0
> > +
> > +title: Freescale i.MX6 PCIe host controller
> > +
> > +maintainers:
> > + - Lucas Stach <l.stach at pengutronix.de>
> > + - Richard Zhu <hongxing.zhu at nxp.com>
> > +
> > +description: |+
> > + This PCIe host controller is based on the Synopsys DesignWare PCIe
> > +IP
> > + and thus inherits all the common properties defined in
> snps,dw-pcie.yaml.
>
> Don't need a freeform text reference, but...
[Richard Zhu] This part is copied from the description of previous the binding document.
Should I remove them totally?
> > +
> > +allOf:
> > + - $ref: /schemas/pci/pci-bus.yaml#
>
> ...this needs to reference the snps,dw-pcie.yaml DWC schema.
>
[Richard Zhu] Got that, would be change in next version patch.
> > +
> > +properties:
> > + compatible:
> > + enum:
> > + - fsl,imx6q-pcie
> > + - fsl,imx6sx-pcie
> > + - fsl,imx6qp-pcie
> > + - fsl,imx7d-pcie
> > + - fsl,imx8mq-pcie
> > +
> > + reg:
> > + items:
> > + - description: Data Bus Interface (DBI) registers.
> > + - description: PCIe configuration space region.
> > +
> > + reg-names:
> > + items:
> > + - const: dbi
> > + - const: config
> > +
> > + interrupts:
> > + minItems: 1
>
> Don't need 'minItems: 1' when there's only 1 possible item:
[Richard Zhu] Okay, would be removed.
>
> > + items:
> > + - description: builtin MSI controller.
> > +
> > + interrupt-names:
> > + minItems: 1
> > + items:
> > + - const: msi
> > +
> > + clocks:
> > + minItems: 3
> > + maxItems: 4
>
> Don't need maxItems here.
>
[Richard Zhu] Okay, would be removed.
> > + items:
> > + - description: PCIe bridge clock.
> > + - description: PCIe bus clock.
> > + - description: PCIe PHY clock.
> > + - description: Additional required clock entry for imx6sx-pcie,
> > + imx8mq-pcie.
> > +
> > + clock-names:
> > + minItems: 3
> > + maxItems: 4
>
> And here.
>
[Richard Zhu] Okay, would be removed.
> > + items:
> > + - const: pcie
> > + - const: pcie_bus
> > + - const: pcie_phy
> > + - const: pcie_inbound_axi for imx6sx-pcie, pcie_aux for
> > + imx8mq-pcie
> > +
> > + num-lanes:
> > + const: 1
> > +
> > + num-viewport:
> > + const: 4
>
> This is deprecated. The driver detects this now.
[Richard Zhu] Got that, thanks. Would delete this property.
>
> > +
> > + fsl,imx7d-pcie-phy:
> > + $ref: /schemas/types.yaml#/definitions/phandle
> > + description: A phandle to an fsl,imx7d-pcie-phy node. Additional
> > + required properties for imx7d-pcie and imx8mq-pcie.
> > +
> > + power-domains:
> > + maxItems: 2
> > + description: The first phandle pointing to the DISPLAY domain for
> > + imx6sx-pcie, to PCIE_PHY power domain for imx7d-pcie and
> imx8mq-pcie.
> > + The second phandle pointing to the PCIE_PHY power domains for
> imx6sx-pcie.
>
> Split the description:
>
> items:
> - description: ...
> - description: ...
>
[Richard Zhu] Got that, thanks.
> > +
> > + power-domain-names:
> > + maxItems: 2
>
> You have to define the names.
>
[Richard Zhu] Okay, would be added in next version patch.
> > +
> > + resets:
> > + maxItems: 3
> > + description: Phandles to PCIe-related reset lines exposed by SRC
> > + IP block. Additional required by imx7d-pcie and imx8mq-pcie.
> > +
> > + reset-names:
> > + items:
> > + - const: pciephy
> > + - const: apps
> > + - const: turnoff
> > +
> > + fsl,tx-deemph-gen1:
> > + description: Gen1 De-emphasis value (optional required).
>
> optional or required?
[Richard Zhu] Yes, it's optional required by i.MX6Q/DL PCIe.
>
> > + $ref: /schemas/types.yaml#/definitions/uint32
> > + default: 0
> > +
> > + fsl,tx-deemph-gen2-3p5db:
> > + description: Gen2 (3.5db) De-emphasis value (optional required).
> > + $ref: /schemas/types.yaml#/definitions/uint32
> > + default: 0
> > +
> > + fsl,tx-deemph-gen2-6db:
> > + description: Gen2 (6db) De-emphasis value (optional required).
> > + $ref: /schemas/types.yaml#/definitions/uint32
> > + default: 20
> > +
> > + fsl,tx-swing-full:
> > + description: Gen2 TX SWING FULL value (optional required).
> > + $ref: /schemas/types.yaml#/definitions/uint32
> > + default: 127
> > +
> > + fsl,tx-swing-low:
> > + description: TX launch amplitude swing_low value (optional required).
> > + $ref: /schemas/types.yaml#/definitions/uint32
> > + default: 127
> > +
> > + fsl,max-link-speed:
> > + description: Specify PCI Gen for link capability (optional required).
> > + Note that the IMX6 LVDS clock outputs do not meet gen2 jitter
> > + requirements and thus for gen2 capability a gen2 compliant clock
> > + generator should be used and configured.
> > + $ref: /schemas/types.yaml#/definitions/uint32
> > + enum: [1, 2, 3, 4]
> > + default: 1
> > +
> > + reset-gpio:
>
> Deprecated.
[Richard Zhu] The reset-gpio is designed to connect the PERST# signal on the slot.
And it is derived from the previous binding document.
>
> > + description: Should specify the GPIO for controlling the PCI bus device
> > + reset signal. It's not polarity aware and defaults to active-low reset
> > + sequence (L=reset state, H=operation state) (optional required).
> > +
> > + reset-gpio-active-high:
>
> Deprecated. This should only be used on older compatibles I hope...
[Richard Zhu] Because that the polarity of the PERST-active is reversed on some i.MX6 customer's
hardware board designs.
This property is derived from the previous binding document, and only be used
on older compatibles. So, this is optional required.
>
> > + description: If present then the reset sequence using the GPIO
> > + specified in the "reset-gpio" property is reversed (H=reset state,
> > + L=operation state) (optional required).
> > +
> > + vpcie-supply:
> > + description: Should specify the regulator in charge of PCIe port power.
> > + The regulator will be enabled when initializing the PCIe host and
> > + disabled either as part of the init process or when shutting down
> > + the host (optional required).
> > +
> > + vph-supply:
> > + description: Should specify the regulator in charge of VPH one of
> > + the three PCIe PHY powers. This regulator can be supplied by both
> > + 1.8v and 3.3v voltage supplies (optional required).
> > +
> > +required:
> > + - compatible
> > + - reg
> > + - reg-names
> > + - "#address-cells"
> > + - "#size-cells"
> > + - device_type
> > + - bus-range
> > + - ranges
> > + - num-lanes
> > + - num-viewport
> > + - interrupts
> > + - interrupt-names
> > + - "#interrupt-cells"
> > + - interrupt-map-mask
> > + - interrupt-map
> > + - clocks
> > + - clock-names
> > +
> > +unevaluatedProperties: false
> > +
> > +examples:
> > + - |
> > + #include <dt-bindings/clock/imx6qdl-clock.h>
> > + #include <dt-bindings/interrupt-controller/arm-gic.h>
> > +
> > + pcie: pcie at 1ffc000 {
> > + compatible = "fsl,imx6q-pcie";
> > + reg = <0x01ffc000 0x04000>,
> > + <0x01f00000 0x80000>;
> > + reg-names = "dbi", "config";
> > + #address-cells = <3>;
> > + #size-cells = <2>;
> > + device_type = "pci";
> > + bus-range = <0x00 0xff>;
> > + ranges = <0x81000000 0 0 0x01f80000 0
> 0x00010000>,
> > + <0x82000000 0 0x01000000 0x01000000 0
> 0x00f00000>;
> > + num-lanes = <1>;
> > + num-viewport = <4>;
> > + interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
> > + interrupt-names = "msi";
> > + #interrupt-cells = <1>;
> > + interrupt-map-mask = <0 0 0 0x7>;
> > + interrupt-map = <0 0 0 1 &gpc GIC_SPI 123
> IRQ_TYPE_LEVEL_HIGH>,
> > + <0 0 0 2 &gpc GIC_SPI 122
> IRQ_TYPE_LEVEL_HIGH>,
> > + <0 0 0 3 &gpc GIC_SPI 121
> IRQ_TYPE_LEVEL_HIGH>,
> > + <0 0 0 4 &gpc GIC_SPI 120
> IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&clks IMX6QDL_CLK_PCIE_AXI>,
> > + <&clks IMX6QDL_CLK_LVDS1_GATE>,
> > + <&clks IMX6QDL_CLK_PCIE_REF_125M>;
> > + clock-names = "pcie", "pcie_bus", "pcie_phy";
> > + status = "disabled";
>
> Why are you disabling your example?
[Richard Zhu] Would remove the disable later. Thanks.
>
> > + };
> > +...
> > diff --git a/MAINTAINERS b/MAINTAINERS index
> > f73fef615702..a1e2cc0be9e8 100644
> > --- a/MAINTAINERS
> > +++ b/MAINTAINERS
> > @@ -14187,7 +14187,7 @@ M: Lucas Stach <l.stach at pengutronix.de>
> > L: linux-pci at vger.kernel.org
> > L: linux-arm-kernel at lists.infradead.org (moderated for
> non-subscribers)
> > S: Maintained
> > -F: Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
> > +F: Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
> > F: drivers/pci/controller/dwc/*imx6*
> >
> > PCI DRIVER FOR FU740
> > --
> > 2.25.1
> >
> >
More information about the linux-arm-kernel
mailing list