[PATCH v1 1/3] dt-bindings: PCI: imx6: convert the imx pcie controller to dtschema
Rob Herring
robh at kernel.org
Mon Aug 23 11:34:08 PDT 2021
On Thu, Aug 19, 2021 at 03:14:06PM +0800, Richard Zhu wrote:
> Convert the fsl,imx6q-pcie.txt into a schema.
> - the ranges should be aligned to $ref: /schemas/pci/pci-bus.yaml#
> - only one propert is allowed in the compatible string, remove
> "snps,dw-pcie".
Didn't I already see a v1?
>
> Signed-off-by: Richard Zhu <hongxing.zhu at nxp.com>
> ---
> .../bindings/pci/fsl,imx6q-pcie.txt | 100 ---------
> .../bindings/pci/fsl,imx6q-pcie.yaml | 207 ++++++++++++++++++
> MAINTAINERS | 2 +-
> 3 files changed, 208 insertions(+), 101 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
> create mode 100644 Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
>
> diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
> deleted file mode 100644
> index d8971ab99274..000000000000
> --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
> +++ /dev/null
> @@ -1,100 +0,0 @@
> -* Freescale i.MX6 PCIe interface
> -
> -This PCIe host controller is based on the Synopsys DesignWare PCIe IP
> -and thus inherits all the common properties defined in designware-pcie.txt.
> -
> -Required properties:
> -- compatible:
> - - "fsl,imx6q-pcie"
> - - "fsl,imx6sx-pcie",
> - - "fsl,imx6qp-pcie"
> - - "fsl,imx7d-pcie"
> - - "fsl,imx8mq-pcie"
> -- reg: base address and length of the PCIe controller
> -- interrupts: A list of interrupt outputs of the controller. Must contain an
> - entry for each entry in the interrupt-names property.
> -- interrupt-names: Must include the following entries:
> - - "msi": The interrupt that is asserted when an MSI is received
> -- clock-names: Must include the following additional entries:
> - - "pcie_phy"
> -
> -Optional properties:
> -- fsl,tx-deemph-gen1: Gen1 De-emphasis value. Default: 0
> -- fsl,tx-deemph-gen2-3p5db: Gen2 (3.5db) De-emphasis value. Default: 0
> -- fsl,tx-deemph-gen2-6db: Gen2 (6db) De-emphasis value. Default: 20
> -- fsl,tx-swing-full: Gen2 TX SWING FULL value. Default: 127
> -- fsl,tx-swing-low: TX launch amplitude swing_low value. Default: 127
> -- fsl,max-link-speed: Specify PCI gen for link capability. Must be '2' for
> - gen2, otherwise will default to gen1. Note that the IMX6 LVDS clock outputs
> - do not meet gen2 jitter requirements and thus for gen2 capability a gen2
> - compliant clock generator should be used and configured.
> -- reset-gpio: Should specify the GPIO for controlling the PCI bus device reset
> - signal. It's not polarity aware and defaults to active-low reset sequence
> - (L=reset state, H=operation state).
> -- reset-gpio-active-high: If present then the reset sequence using the GPIO
> - specified in the "reset-gpio" property is reversed (H=reset state,
> - L=operation state).
> -- vpcie-supply: Should specify the regulator in charge of PCIe port power.
> - The regulator will be enabled when initializing the PCIe host and
> - disabled either as part of the init process or when shutting down the
> - host.
> -- vph-supply: Should specify the regulator in charge of VPH one of the three
> - PCIe PHY powers. This regulator can be supplied by both 1.8v and 3.3v voltage
> - supplies.
> -
> -Additional required properties for imx6sx-pcie:
> -- clock names: Must include the following additional entries:
> - - "pcie_inbound_axi"
> -- power-domains: Must be set to phandles pointing to the DISPLAY and
> - PCIE_PHY power domains
> -- power-domain-names: Must be "pcie", "pcie_phy"
> -
> -Additional required properties for imx7d-pcie and imx8mq-pcie:
> -- power-domains: Must be set to a phandle pointing to PCIE_PHY power domain
> -- resets: Must contain phandles to PCIe-related reset lines exposed by SRC
> - IP block
> -- reset-names: Must contain the following entries:
> - - "pciephy"
> - - "apps"
> - - "turnoff"
> -- fsl,imx7d-pcie-phy: A phandle to an fsl,imx7d-pcie-phy node.
> -
> -Additional required properties for imx8mq-pcie:
> -- clock-names: Must include the following additional entries:
> - - "pcie_aux"
> -
> -Example:
> -
> - pcie at 01000000 {
> - compatible = "fsl,imx6q-pcie", "snps,dw-pcie";
> - reg = <0x01ffc000 0x04000>,
> - <0x01f00000 0x80000>;
> - reg-names = "dbi", "config";
> - #address-cells = <3>;
> - #size-cells = <2>;
> - device_type = "pci";
> - ranges = <0x00000800 0 0x01f00000 0x01f00000 0 0x00080000
> - 0x81000000 0 0 0x01f80000 0 0x00010000
> - 0x82000000 0 0x01000000 0x01000000 0 0x00f00000>;
> - num-lanes = <1>;
> - interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
> - interrupt-names = "msi";
> - #interrupt-cells = <1>;
> - interrupt-map-mask = <0 0 0 0x7>;
> - interrupt-map = <0 0 0 1 &intc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
> - <0 0 0 2 &intc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
> - <0 0 0 3 &intc GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
> - <0 0 0 4 &intc GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&clks 144>, <&clks 206>, <&clks 189>;
> - clock-names = "pcie", "pcie_bus", "pcie_phy";
> - };
> -
> -* Freescale i.MX7d PCIe PHY
> -
> -This is the PHY associated with the IMX7d PCIe controller. It's used by the
> -PCI-e controller via the fsl,imx7d-pcie-phy phandle.
> -
> -Required properties:
> -- compatible:
> - - "fsl,imx7d-pcie-phy"
> -- reg: base address and length of the PCIe PHY controller
> diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
> new file mode 100644
> index 000000000000..3503ce3de05d
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
> @@ -0,0 +1,207 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pci/fsl,imx6q-pcie.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Freescale i.MX6 PCIe host controller
> +
> +maintainers:
> + - Lucas Stach <l.stach at pengutronix.de>
> + - Richard Zhu <hongxing.zhu at nxp.com>
> +
> +description: |+
> + This PCIe host controller is based on the Synopsys DesignWare PCIe IP
> + and thus inherits all the common properties defined in snps,dw-pcie.yaml.
Don't need a freeform text reference, but...
> +
> +allOf:
> + - $ref: /schemas/pci/pci-bus.yaml#
...this needs to reference the snps,dw-pcie.yaml DWC schema.
> +
> +properties:
> + compatible:
> + enum:
> + - fsl,imx6q-pcie
> + - fsl,imx6sx-pcie
> + - fsl,imx6qp-pcie
> + - fsl,imx7d-pcie
> + - fsl,imx8mq-pcie
> +
> + reg:
> + items:
> + - description: Data Bus Interface (DBI) registers.
> + - description: PCIe configuration space region.
> +
> + reg-names:
> + items:
> + - const: dbi
> + - const: config
> +
> + interrupts:
> + minItems: 1
Don't need 'minItems: 1' when there's only 1 possible item:
> + items:
> + - description: builtin MSI controller.
> +
> + interrupt-names:
> + minItems: 1
> + items:
> + - const: msi
> +
> + clocks:
> + minItems: 3
> + maxItems: 4
Don't need maxItems here.
> + items:
> + - description: PCIe bridge clock.
> + - description: PCIe bus clock.
> + - description: PCIe PHY clock.
> + - description: Additional required clock entry for imx6sx-pcie,
> + imx8mq-pcie.
> +
> + clock-names:
> + minItems: 3
> + maxItems: 4
And here.
> + items:
> + - const: pcie
> + - const: pcie_bus
> + - const: pcie_phy
> + - const: pcie_inbound_axi for imx6sx-pcie, pcie_aux for imx8mq-pcie
> +
> + num-lanes:
> + const: 1
> +
> + num-viewport:
> + const: 4
This is deprecated. The driver detects this now.
> +
> + fsl,imx7d-pcie-phy:
> + $ref: /schemas/types.yaml#/definitions/phandle
> + description: A phandle to an fsl,imx7d-pcie-phy node. Additional
> + required properties for imx7d-pcie and imx8mq-pcie.
> +
> + power-domains:
> + maxItems: 2
> + description: The first phandle pointing to the DISPLAY domain for
> + imx6sx-pcie, to PCIE_PHY power domain for imx7d-pcie and imx8mq-pcie.
> + The second phandle pointing to the PCIE_PHY power domains for imx6sx-pcie.
Split the description:
items:
- description: ...
- description: ...
> +
> + power-domain-names:
> + maxItems: 2
You have to define the names.
> +
> + resets:
> + maxItems: 3
> + description: Phandles to PCIe-related reset lines exposed by SRC
> + IP block. Additional required by imx7d-pcie and imx8mq-pcie.
> +
> + reset-names:
> + items:
> + - const: pciephy
> + - const: apps
> + - const: turnoff
> +
> + fsl,tx-deemph-gen1:
> + description: Gen1 De-emphasis value (optional required).
optional or required?
> + $ref: /schemas/types.yaml#/definitions/uint32
> + default: 0
> +
> + fsl,tx-deemph-gen2-3p5db:
> + description: Gen2 (3.5db) De-emphasis value (optional required).
> + $ref: /schemas/types.yaml#/definitions/uint32
> + default: 0
> +
> + fsl,tx-deemph-gen2-6db:
> + description: Gen2 (6db) De-emphasis value (optional required).
> + $ref: /schemas/types.yaml#/definitions/uint32
> + default: 20
> +
> + fsl,tx-swing-full:
> + description: Gen2 TX SWING FULL value (optional required).
> + $ref: /schemas/types.yaml#/definitions/uint32
> + default: 127
> +
> + fsl,tx-swing-low:
> + description: TX launch amplitude swing_low value (optional required).
> + $ref: /schemas/types.yaml#/definitions/uint32
> + default: 127
> +
> + fsl,max-link-speed:
> + description: Specify PCI Gen for link capability (optional required).
> + Note that the IMX6 LVDS clock outputs do not meet gen2 jitter
> + requirements and thus for gen2 capability a gen2 compliant clock
> + generator should be used and configured.
> + $ref: /schemas/types.yaml#/definitions/uint32
> + enum: [1, 2, 3, 4]
> + default: 1
> +
> + reset-gpio:
Deprecated.
> + description: Should specify the GPIO for controlling the PCI bus device
> + reset signal. It's not polarity aware and defaults to active-low reset
> + sequence (L=reset state, H=operation state) (optional required).
> +
> + reset-gpio-active-high:
Deprecated. This should only be used on older compatibles I hope...
> + description: If present then the reset sequence using the GPIO
> + specified in the "reset-gpio" property is reversed (H=reset state,
> + L=operation state) (optional required).
> +
> + vpcie-supply:
> + description: Should specify the regulator in charge of PCIe port power.
> + The regulator will be enabled when initializing the PCIe host and
> + disabled either as part of the init process or when shutting down
> + the host (optional required).
> +
> + vph-supply:
> + description: Should specify the regulator in charge of VPH one of
> + the three PCIe PHY powers. This regulator can be supplied by both
> + 1.8v and 3.3v voltage supplies (optional required).
> +
> +required:
> + - compatible
> + - reg
> + - reg-names
> + - "#address-cells"
> + - "#size-cells"
> + - device_type
> + - bus-range
> + - ranges
> + - num-lanes
> + - num-viewport
> + - interrupts
> + - interrupt-names
> + - "#interrupt-cells"
> + - interrupt-map-mask
> + - interrupt-map
> + - clocks
> + - clock-names
> +
> +unevaluatedProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/clock/imx6qdl-clock.h>
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> +
> + pcie: pcie at 1ffc000 {
> + compatible = "fsl,imx6q-pcie";
> + reg = <0x01ffc000 0x04000>,
> + <0x01f00000 0x80000>;
> + reg-names = "dbi", "config";
> + #address-cells = <3>;
> + #size-cells = <2>;
> + device_type = "pci";
> + bus-range = <0x00 0xff>;
> + ranges = <0x81000000 0 0 0x01f80000 0 0x00010000>,
> + <0x82000000 0 0x01000000 0x01000000 0 0x00f00000>;
> + num-lanes = <1>;
> + num-viewport = <4>;
> + interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "msi";
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0 0 0 0x7>;
> + interrupt-map = <0 0 0 1 &gpc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 2 &gpc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 3 &gpc GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 4 &gpc GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&clks IMX6QDL_CLK_PCIE_AXI>,
> + <&clks IMX6QDL_CLK_LVDS1_GATE>,
> + <&clks IMX6QDL_CLK_PCIE_REF_125M>;
> + clock-names = "pcie", "pcie_bus", "pcie_phy";
> + status = "disabled";
Why are you disabling your example?
> + };
> +...
> diff --git a/MAINTAINERS b/MAINTAINERS
> index f73fef615702..a1e2cc0be9e8 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -14187,7 +14187,7 @@ M: Lucas Stach <l.stach at pengutronix.de>
> L: linux-pci at vger.kernel.org
> L: linux-arm-kernel at lists.infradead.org (moderated for non-subscribers)
> S: Maintained
> -F: Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
> +F: Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
> F: drivers/pci/controller/dwc/*imx6*
>
> PCI DRIVER FOR FU740
> --
> 2.25.1
>
>
More information about the linux-arm-kernel
mailing list