[PATCH] rockchip: enabled LAN port on NanoPi R2S

[Tianling Shen]

Hi Chen-Yu,

On 2021-04-05 16:14, Chen-Yu Tsai <wens at kernel.org> wrote:
>
> Hi,
>
> On Mon, Apr 5, 2021 at 3:46 PM Tianling Shen <cnsztl at gmail.com> wrote:
> >
> > From: David Bauer <mail at david-bauer.net>
> >
> > Enable the USB3 port on the FriendlyARM NanoPi R2S.
> > This is required for the USB3 attached LAN port to work.
> >
> > Signed-off-by: David Bauer <mail at david-bauer.net>
> > Signed-off-by: Tianling Shen <cnsztl at gmail.com>
> > ---
> >  .../boot/dts/rockchip/rk3328-nanopi-r2s.dts   | 23 +++++++++++++++++++
> >  1 file changed, 23 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts b/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts
> > index faf496d789cf..6ba9799a95c5 100644
> > --- a/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts
> > +++ b/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts
> > @@ -37,6 +37,18 @@
> >                 };
> >         };
> >
> > +       vcc_rtl8153: vcc-rtl8153-regulator {
> > +               compatible = "regulator-fixed";
> > +               gpio = <&gpio2 RK_PC6 GPIO_ACTIVE_HIGH>;
> > +               pinctrl-names = "default";
> > +               pinctrl-0 = <&rtl8153_en_drv>;
> > +               regulator-always-on;
> > +               regulator-name = "vcc_rtl8153";
> > +               regulator-min-microvolt = <5000000>;
> > +               regulator-max-microvolt = <5000000>;
>
> This is just a simple switch, not an actual regulator.
> It would make more sense to drop the voltage range and
> instead have the implementation pass-through voltage
> constraints from its parent.

Thanks, I'll remove them in v2.

>
> > +               enable-active-high;
> > +       };
> > +
> >         leds {
> >                 compatible = "gpio-leds";
> >                 pinctrl-0 = <&lan_led_pin>,  <&sys_led_pin>, <&wan_led_pin>;
> > @@ -265,6 +277,12 @@
> >                         };
> >                 };
> >         };
> > +
> > +       usb {
> > +               rtl8153_en_drv: rtl8153-en-drv {
> > +                       rockchip,pins = <2 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
> > +               };
> > +       };
> >  };
> >
> >  &io_domains {
> > @@ -364,6 +382,11 @@
> >         dr_mode = "host";
> >  };
> >
> > +&usbdrd3 {
> > +       dr_mode = "host";
> > +       status = "okay";
>
> Please also add a device node for the actual Ethernet controller, and
> set up an aliases node for it, so that the bootloader has some place
> to fill in a MAC address.

But there's no valid (unique) MAC address for both this or on-board ethernet...
They're non-existent in design.

Thanks,
Tianling.

>
>
> ChenYu
>
> > +};
> > +
> >  &usb_host0_ehci {
> >         status = "okay";
> >  };
> > --
> > 2.17.1
> >
> >
> > _______________________________________________
> > linux-arm-kernel mailing list
> > linux-arm-kernel at lists.infradead.org
> > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel