[PATCH] rockchip: enabled LAN port on NanoPi R2S

[Chen-Yu Tsai]

Hi,

On Mon, Apr 5, 2021 at 3:46 PM Tianling Shen <cnsztl at gmail.com> wrote:
>
> From: David Bauer <mail at david-bauer.net>
>
> Enable the USB3 port on the FriendlyARM NanoPi R2S.
> This is required for the USB3 attached LAN port to work.
>
> Signed-off-by: David Bauer <mail at david-bauer.net>
> Signed-off-by: Tianling Shen <cnsztl at gmail.com>
> ---
>  .../boot/dts/rockchip/rk3328-nanopi-r2s.dts   | 23 +++++++++++++++++++
>  1 file changed, 23 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts b/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts
> index faf496d789cf..6ba9799a95c5 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts
> +++ b/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts
> @@ -37,6 +37,18 @@
>                 };
>         };
>
> +       vcc_rtl8153: vcc-rtl8153-regulator {
> +               compatible = "regulator-fixed";
> +               gpio = <&gpio2 RK_PC6 GPIO_ACTIVE_HIGH>;
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&rtl8153_en_drv>;
> +               regulator-always-on;
> +               regulator-name = "vcc_rtl8153";
> +               regulator-min-microvolt = <5000000>;
> +               regulator-max-microvolt = <5000000>;

This is just a simple switch, not an actual regulator.
It would make more sense to drop the voltage range and
instead have the implementation pass-through voltage
constraints from its parent.

> +               enable-active-high;
> +       };
> +
>         leds {
>                 compatible = "gpio-leds";
>                 pinctrl-0 = <&lan_led_pin>,  <&sys_led_pin>, <&wan_led_pin>;
> @@ -265,6 +277,12 @@
>                         };
>                 };
>         };
> +
> +       usb {
> +               rtl8153_en_drv: rtl8153-en-drv {
> +                       rockchip,pins = <2 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
> +               };
> +       };
>  };
>
>  &io_domains {
> @@ -364,6 +382,11 @@
>         dr_mode = "host";
>  };
>
> +&usbdrd3 {
> +       dr_mode = "host";
> +       status = "okay";

Please also add a device node for the actual Ethernet controller, and
set up an aliases node for it, so that the bootloader has some place
to fill in a MAC address.


ChenYu

> +};
> +
>  &usb_host0_ehci {
>         status = "okay";
>  };
> --
> 2.17.1
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel