[PATCH v11 04/11] PCI: brcmstb: Add suspend and resume pm_ops

[Rob Herring]

On Thu, Sep 10, 2020 at 10:42 AM Jim Quinlan <james.quinlan at broadcom.com> wrote:
>
> On Thu, Sep 10, 2020 at 11:56 AM Rob Herring <robh at kernel.org> wrote:
> >
> > On Mon, Aug 24, 2020 at 03:30:17PM -0400, Jim Quinlan wrote:
> > > From: Jim Quinlan <jquinlan at broadcom.com>
> > >
> > > Broadcom Set-top (BrcmSTB) boards typically support S2, S3, and S5 suspend
> > > and resume.  Now the PCIe driver may do so as well.
> > >
> > > Signed-off-by: Jim Quinlan <jquinlan at broadcom.com>
> > > Acked-by: Florian Fainelli <f.fainelli at gmail.com>
> > > ---
> > >  drivers/pci/controller/pcie-brcmstb.c | 47 +++++++++++++++++++++++++++
> > >  1 file changed, 47 insertions(+)
> > >
> > > diff --git a/drivers/pci/controller/pcie-brcmstb.c b/drivers/pci/controller/pcie-brcmstb.c
> > > index c2b3d2946a36..3d588ab7a6dd 100644
> > > --- a/drivers/pci/controller/pcie-brcmstb.c
> > > +++ b/drivers/pci/controller/pcie-brcmstb.c
> > > @@ -978,6 +978,47 @@ static void brcm_pcie_turn_off(struct brcm_pcie *pcie)
> > >       brcm_pcie_bridge_sw_init_set(pcie, 1);
> > >  }
> > >
> > > +static int brcm_pcie_suspend(struct device *dev)
> > > +{
> > > +     struct brcm_pcie *pcie = dev_get_drvdata(dev);
> > > +
> > > +     brcm_pcie_turn_off(pcie);
> > > +     clk_disable_unprepare(pcie->clk);
> > > +
> > > +     return 0;
> > > +}
> > > +
> > > +static int brcm_pcie_resume(struct device *dev)
> > > +{
> > > +     struct brcm_pcie *pcie = dev_get_drvdata(dev);
> > > +     void __iomem *base;
> > > +     u32 tmp;
> > > +     int ret;
> > > +
> > > +     base = pcie->base;
> > > +     clk_prepare_enable(pcie->clk);
> > > +
> > > +     /* Take bridge out of reset so we can access the SERDES reg */
> > > +     brcm_pcie_bridge_sw_init_set(pcie, 0);
> > > +
> > > +     /* SERDES_IDDQ = 0 */
> > > +     tmp = readl(base + PCIE_MISC_HARD_PCIE_HARD_DEBUG);
> > > +     u32p_replace_bits(&tmp, 0, PCIE_MISC_HARD_PCIE_HARD_DEBUG_SERDES_IDDQ_MASK);
> > > +     writel(tmp, base + PCIE_MISC_HARD_PCIE_HARD_DEBUG);
> > > +
> > > +     /* wait for serdes to be stable */
> > > +     udelay(100);
> >
> > Really needs to be a spinloop?
> >
> > > +
> > > +     ret = brcm_pcie_setup(pcie);
> > > +     if (ret)
> > > +             return ret;
> > > +
> > > +     if (pcie->msi)
> > > +             brcm_msi_set_regs(pcie->msi);
> > > +
> > > +     return 0;
> > > +}
> > > +
> > >  static void __brcm_pcie_remove(struct brcm_pcie *pcie)
> > >  {
> > >       brcm_msi_remove(pcie);
> > > @@ -1087,12 +1128,18 @@ static int brcm_pcie_probe(struct platform_device *pdev)
> > >
> > >  MODULE_DEVICE_TABLE(of, brcm_pcie_match);
> > >
> > > +static const struct dev_pm_ops brcm_pcie_pm_ops = {
> > > +     .suspend_noirq = brcm_pcie_suspend,
> > > +     .resume_noirq = brcm_pcie_resume,
> >
> > Why do you need interrupts disabled? There's 39 cases of .suspend_noirq
> > and 1352 of .suspend in the tree.
>
> I will test switching this to  suspend_late/resume_early.

Why not just the 'regular' flavor suspend/resume?

Rob