[PATCH 2/2] arm64: dts: imx8mm: Add Gateworks IMX8MM Development Kits
Krzysztof Kozlowski
krzk at kernel.org
Thu Dec 24 06:37:27 EST 2020
On Wed, Dec 23, 2020 at 02:23:16PM -0800, Tim Harvey wrote:
> The Gateworks Venice GW71xx-0x/GW72xx-0x/GW73xx-0x are development
> kits comprised of a GW700x SoM and a Baseboard.
>
> The GW700x SoM contains:
> - IMX8MM SoC
It's i.MX 8M Mini.
https://www.nxp.com/products/processors-and-microcontrollers/arm-processors/i-mx-applications-processors/i-mx-8-processors/i-mx-8m-mini-arm-cortex-a53-cortex-m4-audio-voice-video:i.MX8MMINI
> - LPDDR4 DRAM
> - eMMC FLASH
> - Gateworks System Controller (eeprom/pushbutton/reset/voltage-monitor)
> - GbE PHY connected to the IMX8MM FEC
> - Power Management IC
>
> The GW71xx Baseboard contains:
> - 1x MiniPCIe Socket with USB2.0, PCIe, and SIM
> - 1x RJ45 GbE (IMX8MM FEC)
> - PCIe Clock generator
> - GPS and accelerometer
> - 1x USB 2.0 Front Panel connector
> - wide range power supply
>
> The GW72xx Baseboard contains:
> - 2x MiniPCIe Socket with USB2.0, PCIe, and SIM
> - 2x RJ45 GbE (IMX8MM FEC and LAN743x)
> - 1x MicroSD connector
> - 1x USB 2.0 Front Panel connector
> - 1x SPI connector
> - PCIe Clock generator
> - GPS and accelerometer
> - Media Expansion connector (MIPI-CSI/MIPI-DSI/GPIO/I2S)
> - wide range power supply
>
> The GW73xx Baseboard contains:
> - 3x MiniPCIe Socket with USB2.0, PCIe, and SIM
> - 2x RJ45 GbE (IMX8MM FEC and LAN743x)
> - 1x MicroSD connector
> - 1x USB 2.0 Front Panel connector
> - 1x SPI connector
> - WiFi/BT
> - PCIe Clock generator
> - GPS and accelerometer
> - Media Expansion connector (MIPI-CSI/MIPI-DSI/GPIO/I2S)
> - wide range power supply
>
> Signed-off-by: Tim Harvey <tharvey at gateworks.com>
> ---
> arch/arm64/boot/dts/freescale/Makefile | 3 +
> .../boot/dts/freescale/imx8mm-venice-gw700x.dtsi | 482 +++++++++++++++++++++
> .../boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts | 19 +
> .../boot/dts/freescale/imx8mm-venice-gw71xx.dtsi | 186 ++++++++
> .../boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts | 20 +
> .../boot/dts/freescale/imx8mm-venice-gw72xx.dtsi | 311 +++++++++++++
> .../boot/dts/freescale/imx8mm-venice-gw73xx-0x.dts | 19 +
> .../boot/dts/freescale/imx8mm-venice-gw73xx.dtsi | 363 ++++++++++++++++
> 8 files changed, 1403 insertions(+)
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw700x.dtsi
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x.dts
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx.dtsi
>
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index f8d5943..ecdd233 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -32,6 +32,9 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-beacon-kit.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mm-ddr4-evk.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mm-var-som-symphony.dtb
> +dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw71xx-0x.dtb
> +dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw72xx-0x.dtb
> +dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw73xx-0x.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mn-var-som-symphony.dtb
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw700x.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw700x.dtsi
> new file mode 100644
> index 00000000..7e1b96b
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw700x.dtsi
> @@ -0,0 +1,482 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2020 Gateworks Corporation
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/linux-event-codes.h>
> +#include <dt-bindings/net/ti-dp83867.h>
> +
> +/ {
> + memory at 40000000 {
> + device_type = "memory";
> + reg = <0x0 0x40000000 0 0x80000000>;
> + };
> +
> + gpio_keys {
> + compatible = "gpio-keys";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + user_pb {
> + label = "user_pb";
> + gpios = <&gsc_gpio 2 GPIO_ACTIVE_LOW>;
> + linux,code = <BTN_0>;
> + };
> +
> + user_pb1x {
> + label = "user_pb1x";
> + linux,code = <BTN_1>;
> + interrupt-parent = <&gsc>;
> + interrupts = <0>;
> + };
> +
> + key_erased {
> + label = "key-erased";
Above you use underscore, here hyphen. Make it consistent.
> + linux,code = <BTN_2>;
> + interrupt-parent = <&gsc>;
> + interrupts = <1>;
> + };
> +
> + eeprom_wp {
> + label = "eeprom_wp";
> + linux,code = <BTN_3>;
> + interrupt-parent = <&gsc>;
> + interrupts = <2>;
> + };
> +
> + tamper {
> + label = "tamper";
> + linux,code = <BTN_4>;
> + interrupt-parent = <&gsc>;
> + interrupts = <5>;
> + };
> +
> + switch_hold {
> + label = "switch_hold";
> + linux,code = <BTN_5>;
> + interrupt-parent = <&gsc>;
> + interrupts = <7>;
> + };
> + };
> +};
> +
> +&A53_0 {
> + cpu-supply = <&buck3_reg>;
> +};
> +
> +&A53_1 {
> + cpu-supply = <&buck3_reg>;
> +};
> +
> +&A53_2 {
> + cpu-supply = <&buck3_reg>;
> +};
> +
> +&A53_3 {
> + cpu-supply = <&buck3_reg>;
> +};
> +
> +&ddrc {
> + operating-points-v2 = <&ddrc_opp_table>;
> +
> + ddrc_opp_table: opp-table {
> + compatible = "operating-points-v2";
> +
> + opp-25M {
> + opp-hz = /bits/ 64 <25000000>;
> + };
> +
> + opp-100M {
> + opp-hz = /bits/ 64 <100000000>;
> + };
> +
> + opp-750M {
> + opp-hz = /bits/ 64 <750000000>;
> + };
> + };
> +};
> +
> +&fec1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fec1>;
> + phy-mode = "rgmii-id";
> + phy-handle = <ðphy0>;
> + status = "okay";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethphy0: ethernet-phy at 0 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <0>;
> + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
> + ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
> + };
> + };
> +};
> +
> +&i2c1 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + status = "okay";
> +
> + gsc: gsc at 20 {
Node name should describe class of a device so maybe
"system-controller"?
> + compatible = "gw,gsc";
> + reg = <0x20>;
> + pinctrl-0 = <&pinctrl_gsc>;
> + interrupt-parent = <&gpio2>;
> + interrupts = <6 GPIO_ACTIVE_LOW>;
Wrong flag.
> + interrupt-controller;
> + #interrupt-cells = <1>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + adc {
Just to be sure - did you build it with W=1 to find any dtc warnings?
> + compatible = "gw,gsc-adc";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + channel at 6 {
> + gw,mode = <0>;
> + reg = <0x06>;
> + label = "temp";
> + };
> +
> + channel at 8 {
> + gw,mode = <1>;
> + reg = <0x08>;
> + label = "vdd_bat";
> + };
> +
> + channel at 16 {
> + gw,mode = <4>;
> + reg = <0x16>;
> + label = "fan_tach";
> + };
> +
> + channel at 82 {
> + gw,mode = <2>;
> + reg = <0x82>;
> + label = "vdd_vin";
> + gw,voltage-divider-ohms = <22100 1000>;
> + };
> +
> + channel at 84 {
> + gw,mode = <2>;
> + reg = <0x84>;
> + label = "vdd_adc1";
> + gw,voltage-divider-ohms = <10000 10000>;
> + };
> +
> + channel at 86 {
> + gw,mode = <2>;
> + reg = <0x86>;
> + label = "vdd_adc2";
> + gw,voltage-divider-ohms = <10000 10000>;
> + };
> +
> + channel at 88 {
> + gw,mode = <2>;
> + reg = <0x88>;
> + label = "vdd_dram";
> + };
> +
> + channel at 8c {
> + gw,mode = <2>;
> + reg = <0x8c>;
> + label = "vdd_1p2";
> + };
> +
> + channel at 8e {
> + gw,mode = <2>;
> + reg = <0x8e>;
> + label = "vdd_1p0";
> + };
> +
> + channel at 90 {
> + gw,mode = <2>;
> + reg = <0x90>;
> + label = "vdd_2p5";
> + gw,voltage-divider-ohms = <10000 10000>;
> + };
> +
> + channel at 92 {
> + gw,mode = <2>;
> + reg = <0x92>;
> + label = "vdd_3p3";
> + gw,voltage-divider-ohms = <10000 10000>;
> + };
> +
> + channel at 98 {
> + gw,mode = <2>;
> + reg = <0x98>;
> + label = "vdd_0p95";
> + };
> +
> + channel at 9a {
> + gw,mode = <2>;
> + reg = <0x9a>;
> + label = "vdd_1p8";
> + };
> +
> + channel at a2 {
> + gw,mode = <2>;
> + reg = <0xa2>;
> + label = "vdd_gsc";
> + gw,voltage-divider-ohms = <10000 10000>;
> + };
> + };
> +
> + fan-controller at 0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
These do not seem needed.
> + compatible = "gw,gsc-fan";
> + reg = <0x0a>;
> + };
> + };
> +
> + gsc_gpio: pca9555 at 23 {
Lookes like gpio-controller, so "gpio". Please run make dtbs_check to be
sure your board validate against dt-schema.
> + compatible = "nxp,pca9555";
> + reg = <0x23>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-parent = <&gsc>;
> + interrupts = <4>;
> + };
> +
> + eeprom at 50 {
> + compatible = "atmel,24c02";
> + reg = <0x50>;
> + pagesize = <16>;
> + };
> +
> + eeprom at 51 {
> + compatible = "atmel,24c02";
> + reg = <0x51>;
> + pagesize = <16>;
> + };
> +
> + eeprom at 52 {
> + compatible = "atmel,24c32";
> + reg = <0x52>;
> + pagesize = <32>;
> + };
> +
> + eeprom at 53 {
> + compatible = "atmel,24c32";
> + reg = <0x53>;
> + pagesize = <32>;
> + };
> +
> + pmic at 69 {
> + compatible = "mps,mp5416";
> + reg = <0x69>;
> +
> + regulators {
> + buck1 {
> + regulator-name = "vdd_0p95";
> + regulator-min-microvolt = <805000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-max-microamp = <2500000>;
> + regulator-boot-on;
> + };
> +
> + buck2 {
> + regulator-name = "vdd_soc";
> + regulator-min-microvolt = <805000>;
> + regulator-max-microvolt = <900000>;
> + regulator-max-microamp = <1000000>;
> + regulator-boot-on;
> + };
> +
> + buck3_reg: buck3 {
> + regulator-name = "vdd_arm";
> + regulator-min-microvolt = <805000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-max-microamp = <2200000>;
> + regulator-boot-on;
> + };
> +
> + buck4 {
> + regulator-name = "vdd_1p8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-max-microamp = <500000>;
> + regulator-boot-on;
> + };
> +
> + ldo1 {
> + regulator-name = "nvcc_snvs_1p8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-max-microamp = <300000>;
> + regulator-boot-on;
> + };
> +
> + ldo2 {
> + regulator-name = "vdd_snvs_0p8";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <800000>;
> + regulator-boot-on;
> + };
> +
> + ldo3 {
> + regulator-name = "vdd_0p95";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <800000>;
> + regulator-boot-on;
> + };
> +
> + ldo4 {
> + regulator-name = "vdd_1p8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + };
> + };
> + };
> +};
> +
> +&i2c2 {
> + clock-frequency = <400000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c2>;
> + status = "okay";
> +
> + eeprom at 52 {
> + compatible = "atmel,24c32";
> + reg = <0x52>;
> + pagesize = <32>;
> + };
> +};
> +
> +&uart2 { /* console */
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart2>;
> + status = "okay";
> +};
> +
> +&usdhc3 { /* eMMC */
> + assigned-clocks = <&clk IMX8MM_CLK_USDHC3_ROOT>;
> + assigned-clock-rates = <400000000>;
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc3>;
> + pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
> + bus-width = <8>;
> + non-removable;
> + status = "okay";
> +};
> +
> +&wdog1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_wdog>;
> + fsl,ext-reset-output;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl_fec1: fec1grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3
> + MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3
> + MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f
> + MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f
> + MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f
> + MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f
> + MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91
> + MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91
> + MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91
> + MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91
> + MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f
> + MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91
> + MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
> + MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f
> + MX8MM_IOMUXC_NAND_ALE_GPIO3_IO0 0x19
> + >;
> + };
> +
> + pinctrl_gsc: gscirq {
grp suffix. I think dtbs_check should point this out.
> + fsl,pins = <
> + MX8MM_IOMUXC_SD1_DATA4_GPIO2_IO6 0x159
> + >;
> + };
> +
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3
> + MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3
> + >;
> + };
> +
> + pinctrl_i2c2: i2c2grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL 0x400001c3
> + MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA 0x400001c3
> + >;
> + };
> +
> + pinctrl_uart2: uart2grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140
> + MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x140
> + >;
> + };
> +
> + pinctrl_usdhc3: usdhc3grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x190
> + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d0
> + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d0
> + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d0
> + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0
> + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d0
> + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d0
> + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d0
> + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d0
> + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d0
> + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x190
> + >;
> + };
> +
> + pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
Ditto
> + fsl,pins = <
> + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x194
> + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d4
> + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
> + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
> + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
> + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
> + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
> + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
> + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
> + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
> + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x194
> + >;
> + };
> +
> + pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
Ditto
> + fsl,pins = <
> + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x196
> + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d6
> + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d6
> + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d6
> + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d6
> + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d6
> + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d6
> + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d6
> + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d6
> + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d6
> + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x196
> + >;
> + };
> +
> + pinctrl_wdog: wdoggrp {
> + fsl,pins = <
> + MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6
> + >;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts
> new file mode 100644
> index 00000000..3f88c4a
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts
> @@ -0,0 +1,19 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2020 Gateworks Corporation
> + */
> +
> +/dts-v1/;
> +
> +#include "imx8mm.dtsi"
> +#include "imx8mm-venice-gw700x.dtsi"
> +#include "imx8mm-venice-gw71xx.dtsi"
> +
> +/ {
> + model = "Gateworks Venice GW71xx-0x i.MX8MM Development Kit";
> + compatible = "gw,imx8mm-gw71xx-0x", "fsl,imx8mm";
> +
> + chosen {
> + stdout-path = &uart2;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi
> new file mode 100644
> index 00000000..a4eeb0d
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi
This file is included only once, so it should be directly inside imx8mm-venice-gw71xx-0x.dts. Do not create empty DTS just to include DTSI and nothing more. It's really over-complicating simple hierarchy.
> @@ -0,0 +1,186 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2020 Gateworks Corporation
> + */
> +
> +/ {
> + aliases {
> + usb0 = &usbotg1;
> + usb1 = &usbotg2;
> + };
> +
> + leds {
led-controller
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpio_leds>;
> +
> + user1 { /* GRN */
led-0
> + label = "user1";
label is now deprecated. See the common bindings.
> + gpios = <&gpio5 5 GPIO_ACTIVE_HIGH>;
> + default-state = "on";
> + linux,default-trigger = "heartbeat";
> + };
> +
> + user2 { /* RED */
led-1
> + label = "user2";
> + gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>;
> + default-state = "off";
> + };
> + };
> +
> + pps {
> + compatible = "pps-gpio";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pps>;
> + gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>;
> + status = "okay";
> + };
> +
> + reg_usb_otg1_vbus: regulator-usb-otg1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_usb1_en>;
> + compatible = "regulator-fixed";
> + regulator-name = "usb_otg1_vbus";
> + gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + };
> +};
> +
> +&ecspi2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_spi2>;
> + cs-gpios = <&gpio5 13 GPIO_ACTIVE_HIGH>;
> + status = "okay";
> +};
> +
> +&i2c2 {
> + clock-frequency = <400000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c2>;
> + status = "okay";
> +
> + accel at 19 {
accelerometer
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_accel>;
> + compatible = "st,lis2de12";
> + reg = <0x19>;
> + st,drdy-int-pin = <1>;
> + interrupt-parent = <&gpio4>;
> + interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
> + interrupt-names = "INT1";
> + };
> +};
> +
> +&i2c3 {
> + clock-frequency = <400000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c3>;
> + status = "okay";
> +};
> +
> +&sai3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_sai3>;
> + assigned-clocks = <&clk IMX8MM_CLK_SAI3>;
> + assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
> + assigned-clock-rates = <24576000>;
> + status = "okay";
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart1>;
> + status = "okay";
> +};
> +
> +&uart3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart3>;
> + status = "okay";
> +};
> +
> +&usbotg1 {
> + dr_mode = "otg";
> + vbus-supply = <®_usb_otg1_vbus>;
> + status = "okay";
> +};
> +
> +&usbotg2 {
> + dr_mode = "host";
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_hog>;
> +
> + pinctrl_hog: hoggrp {
> + fsl,pins = <
> + MX8MM_IOMUXC_SPDIF_TX_GPIO5_IO3 0x40000041 /* PLUG_TEST */
> + MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x40000041 /* PCI_USBSEL */
> + MX8MM_IOMUXC_SAI1_RXD5_GPIO4_IO7 0x40000041 /* PCIE_WDIS# */
> + MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x40000041 /* DIO0 */
> + MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x40000041 /* DIO1 */
> + MX8MM_IOMUXC_SAI1_RXD1_GPIO4_IO3 0x40000041 /* DIO2 */
> + MX8MM_IOMUXC_SAI1_RXD2_GPIO4_IO4 0x40000041 /* DIO2 */
> + >;
> + };
> +
> + pinctrl_accel: accelirq {
Same comments as before.
> + fsl,pins = <
> + MX8MM_IOMUXC_SAI1_RXD3_GPIO4_IO5 0x159
> + >;
> + };
> +
> + pinctrl_gpio_leds: gpioledgrp {
> + fsl,pins = <
> + MX8MM_IOMUXC_SPDIF_EXT_CLK_GPIO5_IO5 0x19
> + MX8MM_IOMUXC_SPDIF_RX_GPIO5_IO4 0x19
> + >;
> + };
> +
> + pinctrl_i2c3: i2c3grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3
> + MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3
> + >;
> + };
> +
> + pinctrl_pps: ppsgrp {
> + fsl,pins = <
> + MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x41
> + >;
> + };
> +
> + pinctrl_reg_usb1_en: regusb1grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12 0x41
> + MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC 0x41
> + >;
> + };
> +
> + pinctrl_spi2: spi2grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0xd6
> + MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0xd6
> + MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0xd6
> + MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0xd6
> + >;
> + };
> +
> + pinctrl_uart1: uart1grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX 0x140
> + MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX 0x140
> + >;
> + };
> +
> + pinctrl_uart3: uart3grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX 0x140
> + MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX 0x140
> + >;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts
> new file mode 100644
> index 00000000..b1e7540
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts
> @@ -0,0 +1,20 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2020 Gateworks Corporation
> + */
> +
> +/dts-v1/;
> +
> +#include "imx8mm.dtsi"
> +#include "imx8mm-venice-gw700x.dtsi"
> +#include "imx8mm-venice-gw72xx.dtsi"
The same - empty DTS just to include DTSI. Don't multiply files. This is
development kit, carrier board, so entire contents of
imx8mm-venice-gw72xx.dtsi is *here*.
> +
> +/ {
> + model = "Gateworks Venice GW72xx-0x i.MX8MM Development Kit";
> + compatible = "gw,imx8mm-gw72xx-0x", "fsl,imx8mm";
> +
> + chosen {
> + stdout-path = &uart2;
> + };
> +};
> +
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi
> new file mode 100644
> index 00000000..3fb0213
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi
> @@ -0,0 +1,311 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2020 Gateworks Corporation
> + */
> +
> +/ {
> + aliases {
> + usb0 = &usbotg1;
> + usb1 = &usbotg2;
> + };
> +
> + leds {
It seems my comments apply to all your files, so I will finish the
review here.
Best regards,
Krzysztof
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpio_leds>;
> +
> + user1 { /* GRN */
> + label = "user1";
> + gpios = <&gpio5 5 GPIO_ACTIVE_HIGH>;
> + default-state = "on";
> + linux,default-trigger = "heartbeat";
> + };
> +
> + user2 { /* RED */
> + label = "user2";
> + gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>;
> + default-state = "off";
> + };
> + };
More information about the linux-arm-kernel
mailing list