[PATCH 4/4] arm64: dts: add support for Marvell cn9130-crb platform
kostap at marvell.com
kostap at marvell.com
Tue Dec 15 10:14:21 EST 2020
From: Konstantin Porotchkin <kostap at marvell.com>
The Marvell reference platform CN9130-CRB is a small form factor
board in a metal case. The platform is based on CN9130 SoC with
addition of 8 Gigabit ports SOHO Ethernet switch.
The reference platform features the following:
* Up to 4 CPU cores ARMv8 Cortex-A72 CPU
* CPU core operating speed of up to 2.2GHz
* DDR4 DIMM – 8GB 64bit+ECC @ 2400Mhz.
* 1x eMMC 8GB device
* 1x uSD card 4 bits port on CP
* 1x 128MB SPI NOR flash memory
* 1x USB 3.0 Host port (Type A)
* 1x SATA Gen3 via M.2
* 1x USB 3.0 via M.2
* 1x SIM card slot
* 1x 1G Ethernet port via RGMII
* 1x 10G port over SFP+ connector
* 8x 1G ports through switch via XFI
* 1x 2.5G/1G/100M/10M port via HS_SGMII
* 1x PCI Express (PCIe)x1 Gen 3.0
* 1x PCI Express (PCIe)x4 Gen 3.0 via NVMe M.2
* JTAG port
The plaform supports two HW configurations - "A" and "B"
CN9130-CRB-A
* AP-MPP configuration: SDIO, UART
* CP0 Serdes configuration:
* Lane0-3: NVMe (PCIe x4)
* Lane4: XFI
* Lane5: HS_SGMII
2. CN9130-CRB-B
* AP-MPP configuration: SDIO, UART
* CP0-MPP configuration: RGMII, SDIO, I2C0, I2C1, SMI, XSMI
* CP0 Serdes configuration:
* Lane0: PCIe x1
* Lane1: USB3_0 x1
* Lane2: SATA x1
* Lane3: USB3_1 x1
* Lane4: XFI
* Lane5: HS_SGMII
Signed-off-by: Konstantin Porotchkin <kostap at marvell.com>
---
arch/arm64/boot/dts/marvell/Makefile | 2 +
arch/arm64/boot/dts/marvell/cn9130-crb-A.dts | 38 ++++
arch/arm64/boot/dts/marvell/cn9130-crb-B.dts | 46 ++++
arch/arm64/boot/dts/marvell/cn9130-crb.dtsi | 221 ++++++++++++++++++++
4 files changed, 307 insertions(+)
create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-A.dts
create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-B.dts
create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
index 995f2e77623c..3b8da909a396 100644
--- a/arch/arm64/boot/dts/marvell/Makefile
+++ b/arch/arm64/boot/dts/marvell/Makefile
@@ -19,3 +19,5 @@ dtb-$(CONFIG_ARCH_MVEBU) += cn9131-db.dtb
dtb-$(CONFIG_ARCH_MVEBU) += cn9131-db-B.dtb
dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db.dtb
dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db-B.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-A.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-B.dtb
diff --git a/arch/arm64/boot/dts/marvell/cn9130-crb-A.dts b/arch/arm64/boot/dts/marvell/cn9130-crb-A.dts
new file mode 100644
index 000000000000..a7b6dfba8af5
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/cn9130-crb-A.dts
@@ -0,0 +1,38 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2020 Marvell International Ltd.
+ */
+
+#include "cn9130-crb.dtsi"
+
+/ {
+ model = "Marvell Armada CN9130-CRB-A";
+};
+
+&cp0_pcie0 {
+ status = "okay";
+ num-lanes = <4>;
+ num-viewport = <8>;
+ /* Generic PHY, providing serdes lanes */
+ phys = <&cp0_comphy0 0
+ &cp0_comphy1 0
+ &cp0_comphy2 0
+ &cp0_comphy3 0>;
+ iommu-map =
+ <0x0 &smmu 0x480 0x20>,
+ <0x100 &smmu 0x4a0 0x20>,
+ <0x200 &smmu 0x4c0 0x20>;
+ iommu-map-mask = <0x031f>;
+};
+
+&cp0_usb3_0 {
+ status = "okay";
+ usb-phy = <&cp0_usb3_0_phy0>;
+ phy-names = "usb";
+};
+
+&cp0_usb3_1 {
+ status = "okay";
+ usb-phy = <&cp0_usb3_0_phy1>;
+ phy-names = "usb";
+};
diff --git a/arch/arm64/boot/dts/marvell/cn9130-crb-B.dts b/arch/arm64/boot/dts/marvell/cn9130-crb-B.dts
new file mode 100644
index 000000000000..0904cb0309ae
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/cn9130-crb-B.dts
@@ -0,0 +1,46 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2020 Marvell International Ltd.
+ */
+
+#include "cn9130-crb.dtsi"
+
+/ {
+ model = "Marvell Armada CN9130-CRB-B";
+};
+
+&cp0_pcie0 {
+ status = "okay";
+ num-lanes = <1>;
+ num-viewport = <8>;
+ /* Generic PHY, providing serdes lanes */
+ phys = <&cp0_comphy0 0>;
+ iommu-map =
+ <0x0 &smmu 0x480 0x20>,
+ <0x100 &smmu 0x4a0 0x20>,
+ <0x200 &smmu 0x4c0 0x20>;
+ iommu-map-mask = <0x031f>;
+};
+
+&cp0_sata0 {
+ status = "okay";
+ sata-port at 0 {
+ status = "okay";
+ /* Generic PHY, providing serdes lanes */
+ phys = <&cp0_comphy2 0>;
+ };
+};
+
+&cp0_usb3_0 {
+ status = "okay";
+ usb-phy = <&cp0_usb3_0_phy0>;
+ phy-names = "usb";
+ phys = <&cp0_comphy1 0>;
+};
+
+&cp0_usb3_1 {
+ status = "okay";
+ usb-phy = <&cp0_usb3_0_phy1>;
+ phy-names = "usb";
+ phys = <&cp0_comphy3 1>;
+};
diff --git a/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi b/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
new file mode 100644
index 000000000000..8b301d0a31c5
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
@@ -0,0 +1,221 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2020 Marvell International Ltd.
+ */
+
+#include "cn9130.dtsi" /* include SoC device tree */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ aliases {
+ i2c0 = &cp0_i2c0;
+ ethernet0 = &cp0_eth0;
+ ethernet1 = &cp0_eth1;
+ ethernet2 = &cp0_eth2;
+ };
+
+ memory at 00000000 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+
+ ap0_reg_mmc_vccq: ap0_mmc_vccq at 0 {
+ compatible = "regulator-gpio";
+ regulator-name = "ap0_mmc_vccq";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ gpios = <&expander0 5 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x1
+ 3300000 0x0>;
+ };
+
+ cp0_reg_usb3_vbus1: cp0_usb3_vbus at 1 {
+ compatible = "regulator-fixed";
+ regulator-name = "cp0-xhci1-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&expander0 8 GPIO_ACTIVE_HIGH>;
+ };
+
+ cp0_usb3_0_phy0: cp0_usb3_phy0 {
+ compatible = "usb-nop-xceiv";
+ };
+
+ cp0_usb3_0_phy1: cp0_usb3_phy1 {
+ compatible = "usb-nop-xceiv";
+ vcc-supply = <&cp0_reg_usb3_vbus1>;
+ };
+
+ cp0_reg_sd_vccq: cp0_sd_vccq at 0 {
+ compatible = "regulator-gpio";
+ regulator-name = "cp0_sd_vccq";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ gpios = <&cp0_gpio2 18 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x1
+ 3300000 0x0>;
+ };
+
+ cp0_reg_sd_vcc: cp0_sd_vcc at 0 {
+ compatible = "regulator-fixed";
+ regulator-name = "cp0_sd_vcc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&cp0_gpio2 19 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+/* on-board eMMC U6 */
+&ap_sdhci0 {
+ pinctrl-names = "default";
+ bus-width = <8>;
+ status = "okay";
+ mmc-ddr-1_8v;
+ mmc-hs400-1_8v;
+ vqmmc-supply = <&ap0_reg_mmc_vccq>;
+};
+
+&cp0_syscon0 {
+ cp0_pinctrl: pinctrl {
+ compatible = "marvell,cp115-standalone-pinctrl";
+
+ cp0_i2c0_pins: cp0-i2c-pins-0 {
+ marvell,pins = "mpp37", "mpp38";
+ marvell,function = "i2c0";
+ };
+ cp0_i2c1_pins: cp0-i2c-pins-1 {
+ marvell,pins = "mpp35", "mpp36";
+ marvell,function = "i2c1";
+ };
+ cp0_sdhci_cd_pins_crb: cp0-sdhci-cd-pins-crb {
+ marvell,pins = "mpp55";
+ marvell,function = "gpio";
+ };
+ cp0_sdhci_pins: cp0-sdhi-pins-0 {
+ marvell,pins = "mpp56", "mpp57", "mpp58",
+ "mpp59", "mpp60", "mpp61";
+ marvell,function = "sdio";
+ };
+ cp0_spi0_pins: cp0-spi-pins-0 {
+ marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
+ marvell,function = "spi1";
+ };
+ };
+};
+
+&cp0_i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_i2c0_pins>;
+ status = "okay";
+ clock-frequency = <100000>;
+ expander0: mcp23x17 at 20 {
+ compatible = "microchip,mcp23017";
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x20>;
+ status = "okay";
+ };
+};
+
+&cp0_i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_i2c1_pins>;
+ clock-frequency = <100000>;
+ status = "okay";
+};
+
+
+&cp0_sdhci0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_sdhci_pins
+ &cp0_sdhci_cd_pins_crb>;
+ bus-width = <4>;
+ vqmmc-supply = <&cp0_reg_sd_vccq>;
+ vmmc-supply = <&cp0_reg_sd_vcc>;
+ status = "okay";
+};
+
+&cp0_spi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_spi0_pins>;
+ reg = <0x700680 0x50>, /* control */
+ <0x2000000 0x1000000>; /* CS0 */
+ status = "okay";
+
+ spi-flash at 0 {
+ #address-cells = <0x1>;
+ #size-cells = <0x1>;
+ compatible = "jedec,spi-nor";
+ reg = <0x0>;
+ /* On-board MUX does not allow higher frequencies */
+ spi-max-frequency = <40000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "U-Boot";
+ reg = <0x0 0x200000>;
+ };
+
+ partition at 400000 {
+ label = "Filesystem";
+ reg = <0x200000 0xe00000>;
+ };
+ };
+ };
+};
+
+&cp0_mdio {
+ status = "okay";
+ phy0: ethernet-phy at 0 {
+ reg = <0>;
+ };
+};
+
+&cp0_xmdio {
+ status = "okay";
+ nbaset_phy0: ethernet-phy at 0 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0>;
+ };
+};
+
+&cp0_ethernet {
+ status = "okay";
+};
+
+&cp0_eth0 {
+ status = "okay";
+ phy-mode = "10gbase-kr";
+ managed = "in-band-status";
+ phys = <&cp0_comphy4 0>;
+};
+
+&cp0_eth1 {
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "rgmii-id";
+};
+
+&cp0_eth2 {
+ status = "okay";
+ phy = <&nbaset_phy0>;
+ phy-mode = "2500base-t";
+ phys = <&cp0_comphy5 2>;
+};
+
--
2.17.1
More information about the linux-arm-kernel
mailing list