[PATCH 07/11] irqchip: stm32: add stm32mp1 support with hierarchy domain

[Rob Herring]

On Wed, May 2, 2018 at 11:03 AM, Ludovic BARRE <ludovic.barre at st.com> wrote:
> Hi Rob
>
>
>
> On 05/01/2018 04:56 PM, Rob Herring wrote:
>>
>> On Thu, Apr 26, 2018 at 06:18:30PM +0200, Ludovic Barre wrote:
>>>
>>> From: Ludovic Barre <ludovic.barre at st.com>
>>>
>>> Exti controller has been differently integrated on stm32mp1 SoC.
>>> A parent irq has only one external interrupt. A hierachy domain could
>>> be used. Handlers are call by parent, each parent interrupt could be
>>> masked and unmasked according to the needs.
>>>
>>> Signed-off-by: Ludovic Barre <ludovic.barre at st.com>
>>> ---
>>>   .../interrupt-controller/st,stm32-exti.txt         |   3 +
>>>   drivers/irqchip/irq-stm32-exti.c                   | 322
>>> +++++++++++++++++++++
>>>   2 files changed, 325 insertions(+)
>>>
>>> diff --git
>>> a/Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt
>>> b/Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt
>>> index edf03f0..136bd61 100644
>>> ---
>>> a/Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt
>>> +++
>>> b/Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt
>>> @@ -5,11 +5,14 @@ Required properties:
>>>   - compatible: Should be:
>>>       "st,stm32-exti"
>>>       "st,stm32h7-exti"
>>> +    "st,stm32mp1-exti"
>>>   - reg: Specifies base physical address and size of the registers
>>>   - interrupt-controller: Indentifies the node as an interrupt controller
>>>   - #interrupt-cells: Specifies the number of cells to encode an
>>> interrupt
>>>     specifier, shall be 2
>>>   - interrupts: interrupts references to primary interrupt controller
>>> +  (only needed for exti controller with multiple exti under
>>> +  same parent interrupt: st,stm32-exti and st,stm32h7-exti")
>>>     Example:
>>>   diff --git a/drivers/irqchip/irq-stm32-exti.c
>>> b/drivers/irqchip/irq-stm32-exti.c
>>> index b38c655..ebf7146 100644
>>> --- a/drivers/irqchip/irq-stm32-exti.c
>>> +++ b/drivers/irqchip/irq-stm32-exti.c
>>
>>
>> [...]
>>
>>> +static const struct stm32_desc_irq stm32mp1_desc_irq[] = {
>>> +       { .exti = 1, .irq_parent = 7 },
>>> +       { .exti = 2, .irq_parent = 8 },
>>> +       { .exti = 3, .irq_parent = 9 },
>>> +       { .exti = 4, .irq_parent = 10 },
>>> +       { .exti = 5, .irq_parent = 23 },
>>> +       { .exti = 6, .irq_parent = 64 },
>>> +       { .exti = 7, .irq_parent = 65 },
>>> +       { .exti = 8, .irq_parent = 66 },
>>> +       { .exti = 9, .irq_parent = 67 },
>>> +       { .exti = 10, .irq_parent = 40 },
>>> +       { .exti = 11, .irq_parent = 42 },
>>> +       { .exti = 12, .irq_parent = 76 },
>>> +       { .exti = 13, .irq_parent = 77 },
>>> +       { .exti = 14, .irq_parent = 121 },
>>> +       { .exti = 15, .irq_parent = 127 },
>>> +       { .exti = 16, .irq_parent = 1 },
>>> +       { .exti = 65, .irq_parent = 144 },
>>> +       { .exti = 68, .irq_parent = 143 },
>>> +       { .exti = 73, .irq_parent = 129 },
>>> +};
>>
>>
>> You can use an interrupt-map property rather than put this into the
>> driver.
>
>
> interrupt-map seemed interesting and promising like used in pci host.
> At first sight this property can't be used into node with
> "interrupt-controller" property (see in drivers/of/irq.c function:
> of_irq_parse_raw) because "of_irq_parse_raw" checks if node got
> it first, and after lookup the interrupt-map.
>
> Rob, Thomas, Jason, Marc what do you prefers or the right ways...?

I believe the correct thing to do is simply drop "interrupt-controller".

Rob