[PATCH v4 2/2] ARM: dts: imx: Add basic dts support for imx6sll EVK board
Jacky Bai
ping.bai at nxp.com
Thu Mar 8 21:06:19 PST 2018
> Subject: Re: [PATCH v4 2/2] ARM: dts: imx: Add basic dts support for imx6sll EVK
> board
>
> On Thu, Mar 08, 2018 at 06:03:44PM +0800, Bai Ping wrote:
> > Add dts file support for imx6sll EVK board.
> >
> > Signed-off-by: Bai Ping <ping.bai at nxp.com>
> > ---
> > change v3->v4
> > - update the license indentifier
> > - remove leading zero of node
> > - remove unused pin from hog group
> > ---
> > Documentation/devicetree/bindings/arm/fsl.txt | 4 +
> > arch/arm/boot/dts/Makefile | 2 +
> > arch/arm/boot/dts/imx6sll-evk.dts | 372
> ++++++++++++++++++++++++++
> > 3 files changed, 378 insertions(+)
> > create mode 100644 arch/arm/boot/dts/imx6sll-evk.dts
> >
> > diff --git a/Documentation/devicetree/bindings/arm/fsl.txt
> > b/Documentation/devicetree/bindings/arm/fsl.txt
> > index cdb9dd7..8a1baa2 100644
> > --- a/Documentation/devicetree/bindings/arm/fsl.txt
> > +++ b/Documentation/devicetree/bindings/arm/fsl.txt
> > @@ -53,6 +53,10 @@ i.MX6 Quad SABRE Automotive Board Required root
> > node properties:
> > - compatible = "fsl,imx6q-sabreauto", "fsl,imx6q";
> >
> > +i.MX6SLL EVK board
> > +Required root node properties:
> > + - compatible = "fsl,imx6sll-evk", "fsl,imx6sll";
> > +
> > Generic i.MX boards
> > -------------------
> >
> > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> > index ade7a38..28bff8b 100644
> > --- a/arch/arm/boot/dts/Makefile
> > +++ b/arch/arm/boot/dts/Makefile
> > @@ -505,6 +505,8 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> > dtb-$(CONFIG_SOC_IMX6SL) += \
> > imx6sl-evk.dtb \
> > imx6sl-warp.dtb
> > +dtb-$(CONFIG_SOC_IMX6SLL) += \
> > + imx6sll-evk.dtb
> > dtb-$(CONFIG_SOC_IMX6SX) += \
> > imx6sx-nitrogen6sx.dtb \
> > imx6sx-sabreauto.dtb \
> > diff --git a/arch/arm/boot/dts/imx6sll-evk.dts
> > b/arch/arm/boot/dts/imx6sll-evk.dts
> > new file mode 100644
> > index 0000000..892fbec
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/imx6sll-evk.dts
> > @@ -0,0 +1,372 @@
> > +//SPDX-License-Identifier: (GPL-2.0 OR MIT)
>
> Missing space after //.
>
OK, will fix the comments of this patch in V5.
Jacky
> > +/*
> > + * Copyright 2016 Freescale Semiconductor, Inc.
> > + * Copyright 2017-2018 NXP.
> > + *
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/input/input.h>
> > +#include "imx6sll.dtsi"
> > +
> > +/ {
> > + model = "Freescale i.MX6SLL EVK Board";
> > + compatible = "fsl,imx6sll-evk", "fsl,imx6sll";
> > +
> > + memory at 80000000 {
> > + reg = <0x80000000 0x80000000>;
> > + };
> > +
> > + backlight {
> > + compatible = "pwm-backlight";
> > + pwms = <&pwm1 0 5000000>;
> > + brightness-levels = <0 4 8 16 32 64 128 255>;
> > + default-brightness-level = <6>;
> > + status = "okay";
> > + };
> > +
> > + reg_usb_otg1_vbus: reg-usb-otg1-vbus {
>
> regulator-xxx for node name.
>
> > + compatible = "regulator-fixed";
> > + regulator-name = "usb_otg1_vbus";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + gpio = <&gpio4 0 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + };
> > +
> > + reg_usb_otg2_vbus: reg-usb-otg2-vbus {
> > + compatible = "regulator-fixed";
> > + regulator-name = "usb_otg2_vbus";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + gpio = <&gpio4 2 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + };
> > +
> > + reg_aud3v: reg-aud3v {
> > + compatible = "regulator-fixed";
> > + regulator-name = "wm8962-supply-3v15";
> > + regulator-min-microvolt = <3150000>;
> > + regulator-max-microvolt = <3150000>;
> > + regulator-boot-on;
> > + };
> > +
> > + reg_aud4v: reg-aud4v {
> > + compatible = "regulator-fixed";
> > + regulator-name = "wm8962-supply-4v2";
> > + regulator-min-microvolt = <4325000>;
> > + regulator-max-microvolt = <4325000>;
> > + regulator-boot-on;
> > + };
> > +
> > + reg_lcd: reg-lcd {
> > + compatible = "regulator-fixed";
> > + regulator-name = "lcd-pwr";
> > + gpio = <&gpio4 8 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + };
> > +
> > + reg_sd1_vmmc: reg-sd1-vmmc {
> > + compatible = "regulator-fixed";
> > + regulator-name = "SD1_SPWR";
> > + regulator-min-microvolt = <3000000>;
> > + regulator-max-microvolt = <3000000>;
> > + gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + };
> > +};
> > +
> > +&cpu0 {
> > + arm-supply = <&sw1a_reg>;
> > + soc-supply = <&sw1c_reg>;
> > +};
> > +
> > +&i2c1 {
> > + clock-frequency = <100000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c1>;
> > + status = "okay";
> > +
> > + pmic: pfuze100 at 8 {
>
> pfuze100: pmic
>
> > + compatible = "fsl,pfuze100";
> > + reg = <0x08>;
> > +
> > + regulators {
> > + sw1a_reg: sw1ab {
> > + regulator-min-microvolt = <300000>;
> > + regulator-max-microvolt = <1875000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + regulator-ramp-delay = <6250>;
> > + };
> > +
> > + sw1c_reg: sw1c {
> > + regulator-min-microvolt = <300000>;
> > + regulator-max-microvolt = <1875000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + regulator-ramp-delay = <6250>;
> > + };
> > +
> > + sw2_reg: sw2 {
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + sw3a_reg: sw3a {
> > + regulator-min-microvolt = <400000>;
> > + regulator-max-microvolt = <1975000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + sw3b_reg: sw3b {
> > + regulator-min-microvolt = <400000>;
> > + regulator-max-microvolt = <1975000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + sw4_reg: sw4 {
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt = <3300000>;
> > + };
> > +
> > + swbst_reg: swbst {
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5150000>;
> > + };
> > +
> > + snvs_reg: vsnvs {
> > + regulator-min-microvolt = <1000000>;
> > + regulator-max-microvolt = <3000000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + vref_reg: vrefddr {
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + vgen1_reg: vgen1 {
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt = <1550000>;
> > + regulator-always-on;
> > + };
> > +
> > + vgen2_reg: vgen2 {
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt = <1550000>;
> > + };
> > +
> > + vgen3_reg: vgen3 {
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <3300000>;
> > + };
> > +
> > + vgen4_reg: vgen4 {
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + };
> > +
> > + vgen5_reg: vgen5 {
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + };
> > +
> > + vgen6_reg: vgen6 {
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&iomuxc {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_hog0>, <&pinctrl_hog1>;
> > +
> > + pinctrl_hog0: hog0grp {
> > + pinmux = <
> > + MX6SLL_PAD_KEY_ROW7__GPIO4_IO07
> > + MX6SLL_PAD_GPIO4_IO22__GPIO4_IO22
> > + MX6SLL_PAD_KEY_COL3__GPIO3_IO30
> > + MX6SLL_PAD_KEY_COL4__GPIO4_IO00
> > + MX6SLL_PAD_KEY_COL5__GPIO4_IO02
>
> I don't think these GPIOs should be in hog group, as they are used by particular
> client device, and should be in pinctrl entries for the client devices.
>
> Shawn
>
> > + >;
> > + slew-rate = <0x1>;
> > + drive-strength = <0x3>;
> > + fsl,pin-speed = <0x1>;
> > + bias-pull-up = <0x1>;
> > + input-schmitt-enable;
> > + };
> > +
> > + pinctrl_hog1: hog1grp {
> > + pinmux = <
> > + /*
> > + * Must set the LVE of pad SD2_RESET, otherwise current
> > + * leakage through eMMC chip will pull high the VCCQ to
> > + * 2.6v, which will impact SD1 and SD3 SD3.0 voltage switch.
> > + */
> > + MX6SLL_PAD_SD2_RESET__GPIO4_IO27
> > + >;
> > + slew-rate = <0x1>;
> > + drive-strength = <0x3>;
> > + fsl,pin-speed = <0x1>;
> > + bias-pull-up = <0x1>;
> > + input-schmitt-enable;
> > + fsl,low-voltage-enable = <0x1>;
> > + };
> > +
> > + pinctrl_uart1: uart1grp {
> > + pinmux = <
> > + MX6SLL_PAD_UART1_TXD__UART1_DCE_TX
> > + MX6SLL_PAD_UART1_RXD__UART1_DCE_RX
> > + >;
> > + slew-rate = <0x1>;
> > + drive-strength = <0x6>;
> > + fsl,pin-speed = <0x2>;
> > + bias-pull-up = <0x2>;
> > + input-schmitt-enable;
> > + };
> > +
> > + pinctrl_usdhc1_data: usdhc1datagrp {
> > + pinmux = <
> > + MX6SLL_PAD_SD1_CMD__SD1_CMD
> > + MX6SLL_PAD_SD1_DATA0__SD1_DATA0
> > + MX6SLL_PAD_SD1_DATA1__SD1_DATA1
> > + MX6SLL_PAD_SD1_DATA2__SD1_DATA2
> > + MX6SLL_PAD_SD1_DATA3__SD1_DATA3
> > + >;
> > + slew-rate = <0x1>;
> > + drive-strength = <0x4>;
> > + fsl,pin-speed = <0x1>;
> > + bias-pull-up = <0x1>;
> > + input-schmitt-enable;
> > + };
> > +
> > + pinctrl_usdhc1_clk: usdhc1clkgrp {
> > + pinmux = <MX6SLL_PAD_SD1_CLK__SD1_CLK>;
> > + slew-rate = <0x1>;
> > + drive-strength = <0x4>;
> > + fsl,pin-speed = <0x1>;
> > + bias-pull-down = <0x0>;
> > + input-schmitt-enable;
> > + };
> > +
> > + pinctrl_usdhc1_data_100mhz: usdhc1datagrp_100mhz {
> > + pinmux = <
> > + MX6SLL_PAD_SD1_CMD__SD1_CMD
> > + MX6SLL_PAD_SD1_DATA0__SD1_DATA0
> > + MX6SLL_PAD_SD1_DATA1__SD1_DATA1
> > + MX6SLL_PAD_SD1_DATA2__SD1_DATA2
> > + MX6SLL_PAD_SD1_DATA3__SD1_DATA3
> > + >;
> > + slew-rate = <0x1>;
> > + drive-strength = <0x4>;
> > + fsl,pin-speed = <0x2>;
> > + bias-pull-up = <0x1>;
> > + input-schmitt-enable;
> > + };
> > +
> > + pinctrl_usdhc1_clk_100mhz: usdhc1clkgrp_100mhz {
> > + pinmux = < MX6SLL_PAD_SD1_CLK__SD1_CLK>;
> > + slew-rate = <0x1>;
> > + drive-strength = <0x4>;
> > + fsl,pin-speed = <0x2>;
> > + bias-pull-down = <0x0>;
> > + input-schmitt-enable;
> > + };
> > +
> > + pinctrl_usdhc1_data_200mhz: usdhc1datagrp_200mhz {
> > + pinmux = <
> > + MX6SLL_PAD_SD1_CMD__SD1_CMD
> > + MX6SLL_PAD_SD1_DATA0__SD1_DATA0
> > + MX6SLL_PAD_SD1_DATA1__SD1_DATA1
> > + MX6SLL_PAD_SD1_DATA2__SD1_DATA2
> > + MX6SLL_PAD_SD1_DATA3__SD1_DATA3
> > + >;
> > + slew-rate = <0x1>;
> > + drive-strength = <0x5>;
> > + fsl,pin-speed = <0x3>;
> > + bias-pull-up = <0x1>;
> > + input-schmitt-enable;
> > + };
> > +
> > + pinctrl_usdhc1_clk_200mhz: usdhc1clkgrp_200mhz {
> > + pinmux = <MX6SLL_PAD_SD1_CLK__SD1_CLK>;
> > + slew-rate = <0x1>;
> > + drive-strength = <0x7>;
> > + fsl,pin-speed = <0x3>;
> > + bias-pull-down = <0x0>;
> > + input-schmitt-enable;
> > + };
> > +
> > + pinctrl_usbotg1: usbotg1grp {
> > + pinmux = <MX6SLL_PAD_EPDC_PWR_COM__USB_OTG1_ID>;
> > + slew-rate = <0x1>;
> > + drive-strength = <0x3>;
> > + fsl,pin-speed = <0x1>;
> > + bias-pull-up = <0x1>;
> > + input-schmitt-enable;
> > + };
> > +
> > + pinctrl_i2c1: i2c1grp {
> > + pinmux = <
> > + MX6SLL_PAD_I2C1_SCL__I2C1_SCL
> > + MX6SLL_PAD_I2C1_SDA__I2C1_SDA
> > + >;
> > + slew-rate = <0x1>;
> > + drive-strength = <0x6>;
> > + fsl,pin-speed = <0x2>;
> > + drive-open-drain;
> > + bias-pull-up = <0x2>;
> > + input-schmitt-enable;
> > + input-enable;
> > + };
> > +};
> > +
> > +&uart1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart1>;
> > + status = "okay";
> > +};
> > +
> > +&usdhc1 {
> > + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> > + pinctrl-0 = <&pinctrl_usdhc1_data>, <&pinctrl_usdhc1_clk>;
> > + pinctrl-1 = <&pinctrl_usdhc1_data_100mhz>,
> <&pinctrl_usdhc1_clk_100mhz>;
> > + pinctrl-2 = <&pinctrl_usdhc1_data_200mhz>,
> <&pinctrl_usdhc1_clk_200mhz>;
> > + cd-gpios = <&gpio4 7 GPIO_ACTIVE_LOW>;
> > + wp-gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
> > + keep-power-in-suspend;
> > + wakeup-source;
> > + vmmc-supply = <®_sd1_vmmc>;
> > + status = "okay";
> > +};
> > +
> > +&usbotg1 {
> > + vbus-supply = <®_usb_otg1_vbus>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usbotg1>;
> > + disable-over-current;
> > + srp-disable;
> > + hnp-disable;
> > + adp-disable;
> > + status = "okay";
> > +};
> > +
> > +&usbotg2 {
> > + vbus-supply = <®_usb_otg2_vbus>;
> > + dr_mode = "host";
> > + disable-over-current;
> > + status = "okay";
> > +};
> > --
> > 1.9.1
> >
> >
> > _______________________________________________
> > linux-arm-kernel mailing list
> > linux-arm-kernel at lists.infradead.org
> > https://emea01.safelinks.protection.outlook.com/?url=http%3A%2F%2Flist
> >
> s.infradead.org%2Fmailman%2Flistinfo%2Flinux-arm-kernel&data=02%7C01%7
> >
> Cping.bai%40nxp.com%7Ccc2d554875244f40801108d5856f03b5%7C686ea1d3
> bc2b4
> >
> c6fa92cd99c5c301635%7C0%7C0%7C636561634214012078&sdata=maWc00%
> 2BYifMKn
> > oiD8rVmQFIWsHDgcIfN58UuarYqfCQ%3D&reserved=0
More information about the linux-arm-kernel
mailing list