[PATCH v4 2/2] ARM: dts: imx: Add basic dts support for imx6sll EVK board

Shawn Guo shawnguo at kernel.org
Thu Mar 8 19:36:13 PST 2018


On Thu, Mar 08, 2018 at 06:03:44PM +0800, Bai Ping wrote:
> Add dts file support for imx6sll EVK board.
> 
> Signed-off-by: Bai Ping <ping.bai at nxp.com>
> ---
>  change v3->v4
>  - update the license indentifier
>  - remove leading zero of node
>  - remove unused pin from hog group
> ---
>  Documentation/devicetree/bindings/arm/fsl.txt |   4 +
>  arch/arm/boot/dts/Makefile                    |   2 +
>  arch/arm/boot/dts/imx6sll-evk.dts             | 372 ++++++++++++++++++++++++++
>  3 files changed, 378 insertions(+)
>  create mode 100644 arch/arm/boot/dts/imx6sll-evk.dts
> 
> diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt
> index cdb9dd7..8a1baa2 100644
> --- a/Documentation/devicetree/bindings/arm/fsl.txt
> +++ b/Documentation/devicetree/bindings/arm/fsl.txt
> @@ -53,6 +53,10 @@ i.MX6 Quad SABRE Automotive Board
>  Required root node properties:
>      - compatible = "fsl,imx6q-sabreauto", "fsl,imx6q";
>  
> +i.MX6SLL EVK board
> +Required root node properties:
> +    - compatible = "fsl,imx6sll-evk", "fsl,imx6sll";
> +
>  Generic i.MX boards
>  -------------------
>  
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index ade7a38..28bff8b 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -505,6 +505,8 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
>  dtb-$(CONFIG_SOC_IMX6SL) += \
>  	imx6sl-evk.dtb \
>  	imx6sl-warp.dtb
> +dtb-$(CONFIG_SOC_IMX6SLL) += \
> +	imx6sll-evk.dtb
>  dtb-$(CONFIG_SOC_IMX6SX) += \
>  	imx6sx-nitrogen6sx.dtb \
>  	imx6sx-sabreauto.dtb \
> diff --git a/arch/arm/boot/dts/imx6sll-evk.dts b/arch/arm/boot/dts/imx6sll-evk.dts
> new file mode 100644
> index 0000000..892fbec
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6sll-evk.dts
> @@ -0,0 +1,372 @@
> +//SPDX-License-Identifier: (GPL-2.0 OR MIT)

Missing space after //.

> +/*
> + * Copyright 2016 Freescale Semiconductor, Inc.
> + * Copyright 2017-2018 NXP.
> + *
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include "imx6sll.dtsi"
> +
> +/ {
> +	model = "Freescale i.MX6SLL EVK Board";
> +	compatible = "fsl,imx6sll-evk", "fsl,imx6sll";
> +
> +	memory at 80000000 {
> +		reg = <0x80000000 0x80000000>;
> +	};
> +
> +	backlight {
> +		compatible = "pwm-backlight";
> +		pwms = <&pwm1 0 5000000>;
> +		brightness-levels = <0 4 8 16 32 64 128 255>;
> +		default-brightness-level = <6>;
> +		status = "okay";
> +	};
> +
> +	reg_usb_otg1_vbus: reg-usb-otg1-vbus {

regulator-xxx for node name.

> +		compatible = "regulator-fixed";
> +		regulator-name = "usb_otg1_vbus";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		gpio = <&gpio4 0 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
> +
> +	reg_usb_otg2_vbus: reg-usb-otg2-vbus {
> +		compatible = "regulator-fixed";
> +		regulator-name = "usb_otg2_vbus";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		gpio = <&gpio4 2 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
> +
> +	reg_aud3v: reg-aud3v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "wm8962-supply-3v15";
> +		regulator-min-microvolt = <3150000>;
> +		regulator-max-microvolt = <3150000>;
> +		regulator-boot-on;
> +	};
> +
> +	reg_aud4v: reg-aud4v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "wm8962-supply-4v2";
> +		regulator-min-microvolt = <4325000>;
> +		regulator-max-microvolt = <4325000>;
> +		regulator-boot-on;
> +	};
> +
> +	reg_lcd: reg-lcd {
> +		compatible = "regulator-fixed";
> +		regulator-name = "lcd-pwr";
> +		gpio = <&gpio4 8 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
> +
> +	reg_sd1_vmmc: reg-sd1-vmmc {
> +		compatible = "regulator-fixed";
> +		regulator-name = "SD1_SPWR";
> +		regulator-min-microvolt = <3000000>;
> +		regulator-max-microvolt = <3000000>;
> +		gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
> +};
> +
> +&cpu0 {
> +	arm-supply = <&sw1a_reg>;
> +	soc-supply = <&sw1c_reg>;
> +};
> +
> +&i2c1 {
> +	clock-frequency = <100000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c1>;
> +	status = "okay";
> +
> +	pmic: pfuze100 at 8 {

pfuze100: pmic

> +		compatible = "fsl,pfuze100";
> +		reg = <0x08>;
> +
> +		regulators {
> +			sw1a_reg: sw1ab {
> +				regulator-min-microvolt = <300000>;
> +				regulator-max-microvolt = <1875000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +				regulator-ramp-delay = <6250>;
> +			};
> +
> +			sw1c_reg: sw1c {
> +				regulator-min-microvolt = <300000>;
> +				regulator-max-microvolt = <1875000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +				regulator-ramp-delay = <6250>;
> +			};
> +
> +			sw2_reg: sw2 {
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			sw3a_reg: sw3a {
> +				regulator-min-microvolt = <400000>;
> +				regulator-max-microvolt = <1975000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			sw3b_reg: sw3b {
> +				regulator-min-microvolt = <400000>;
> +				regulator-max-microvolt = <1975000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			sw4_reg: sw4 {
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <3300000>;
> +			};
> +
> +			swbst_reg: swbst {
> +				regulator-min-microvolt = <5000000>;
> +				regulator-max-microvolt = <5150000>;
> +			};
> +
> +			snvs_reg: vsnvs {
> +				regulator-min-microvolt = <1000000>;
> +				regulator-max-microvolt = <3000000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			vref_reg: vrefddr {
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			vgen1_reg: vgen1 {
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <1550000>;
> +				regulator-always-on;
> +			};
> +
> +			vgen2_reg: vgen2 {
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <1550000>;
> +			};
> +
> +			vgen3_reg: vgen3 {
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <3300000>;
> +			};
> +
> +			vgen4_reg: vgen4 {
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-always-on;
> +			};
> +
> +			vgen5_reg: vgen5 {
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-always-on;
> +			};
> +
> +			vgen6_reg: vgen6 {
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-always-on;
> +			};
> +		};
> +	};
> +};
> +
> +&iomuxc {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_hog0>, <&pinctrl_hog1>;
> +
> +	pinctrl_hog0: hog0grp {
> +		pinmux = <
> +			MX6SLL_PAD_KEY_ROW7__GPIO4_IO07
> +			MX6SLL_PAD_GPIO4_IO22__GPIO4_IO22
> +			MX6SLL_PAD_KEY_COL3__GPIO3_IO30
> +			MX6SLL_PAD_KEY_COL4__GPIO4_IO00
> +			MX6SLL_PAD_KEY_COL5__GPIO4_IO02

I don't think these GPIOs should be in hog group, as they are used by
particular client device, and should be in pinctrl entries for the
client devices.

Shawn

> +		>;
> +		slew-rate = <0x1>;
> +		drive-strength = <0x3>;
> +		fsl,pin-speed = <0x1>;
> +		bias-pull-up = <0x1>;
> +		input-schmitt-enable;
> +	};
> +
> +	pinctrl_hog1: hog1grp {
> +		pinmux = <
> +			/*
> +			 * Must set the LVE of pad SD2_RESET, otherwise current
> +			 * leakage through eMMC chip will pull high the VCCQ to
> +			 * 2.6v, which will impact SD1 and SD3 SD3.0 voltage switch.
> +			 */
> +			MX6SLL_PAD_SD2_RESET__GPIO4_IO27
> +		>;
> +		slew-rate = <0x1>;
> +		drive-strength = <0x3>;
> +		fsl,pin-speed = <0x1>;
> +		bias-pull-up = <0x1>;
> +		input-schmitt-enable;
> +		fsl,low-voltage-enable = <0x1>;
> +	};
> +
> +	pinctrl_uart1: uart1grp {
> +		pinmux = <
> +			MX6SLL_PAD_UART1_TXD__UART1_DCE_TX
> +			MX6SLL_PAD_UART1_RXD__UART1_DCE_RX
> +		>;
> +		slew-rate = <0x1>;
> +		drive-strength = <0x6>;
> +		fsl,pin-speed = <0x2>;
> +		bias-pull-up = <0x2>;
> +		input-schmitt-enable;
> +	};
> +
> +	pinctrl_usdhc1_data: usdhc1datagrp {
> +		pinmux = <
> +			MX6SLL_PAD_SD1_CMD__SD1_CMD
> +			MX6SLL_PAD_SD1_DATA0__SD1_DATA0
> +			MX6SLL_PAD_SD1_DATA1__SD1_DATA1
> +			MX6SLL_PAD_SD1_DATA2__SD1_DATA2
> +			MX6SLL_PAD_SD1_DATA3__SD1_DATA3
> +		>;
> +		slew-rate = <0x1>;
> +		drive-strength = <0x4>;
> +		fsl,pin-speed = <0x1>;
> +		bias-pull-up = <0x1>;
> +		input-schmitt-enable;
> +	};
> +
> +	pinctrl_usdhc1_clk: usdhc1clkgrp {
> +		pinmux = <MX6SLL_PAD_SD1_CLK__SD1_CLK>;
> +		slew-rate = <0x1>;
> +		drive-strength = <0x4>;
> +		fsl,pin-speed = <0x1>;
> +		bias-pull-down = <0x0>;
> +		input-schmitt-enable;
> +	};
> +
> +	pinctrl_usdhc1_data_100mhz: usdhc1datagrp_100mhz {
> +		pinmux = <
> +			MX6SLL_PAD_SD1_CMD__SD1_CMD
> +			MX6SLL_PAD_SD1_DATA0__SD1_DATA0
> +			MX6SLL_PAD_SD1_DATA1__SD1_DATA1
> +			MX6SLL_PAD_SD1_DATA2__SD1_DATA2
> +			MX6SLL_PAD_SD1_DATA3__SD1_DATA3
> +		>;
> +		slew-rate = <0x1>;
> +		drive-strength = <0x4>;
> +		fsl,pin-speed = <0x2>;
> +		bias-pull-up = <0x1>;
> +		input-schmitt-enable;
> +	};
> +
> +	pinctrl_usdhc1_clk_100mhz: usdhc1clkgrp_100mhz {
> +		pinmux = < MX6SLL_PAD_SD1_CLK__SD1_CLK>;
> +		slew-rate = <0x1>;
> +		drive-strength = <0x4>;
> +		fsl,pin-speed = <0x2>;
> +		bias-pull-down = <0x0>;
> +		input-schmitt-enable;
> +	};
> +
> +	pinctrl_usdhc1_data_200mhz: usdhc1datagrp_200mhz {
> +		pinmux = <
> +			MX6SLL_PAD_SD1_CMD__SD1_CMD
> +			MX6SLL_PAD_SD1_DATA0__SD1_DATA0
> +			MX6SLL_PAD_SD1_DATA1__SD1_DATA1
> +			MX6SLL_PAD_SD1_DATA2__SD1_DATA2
> +			MX6SLL_PAD_SD1_DATA3__SD1_DATA3
> +		>;
> +		slew-rate = <0x1>;
> +		drive-strength = <0x5>;
> +		fsl,pin-speed = <0x3>;
> +		bias-pull-up = <0x1>;
> +		input-schmitt-enable;
> +	};
> +
> +	pinctrl_usdhc1_clk_200mhz: usdhc1clkgrp_200mhz {
> +		pinmux = <MX6SLL_PAD_SD1_CLK__SD1_CLK>;
> +		slew-rate = <0x1>;
> +		drive-strength = <0x7>;
> +		fsl,pin-speed = <0x3>;
> +		bias-pull-down = <0x0>;
> +		input-schmitt-enable;
> +	};
> +
> +	pinctrl_usbotg1: usbotg1grp {
> +		pinmux = <MX6SLL_PAD_EPDC_PWR_COM__USB_OTG1_ID>;
> +		slew-rate = <0x1>;
> +		drive-strength = <0x3>;
> +		fsl,pin-speed = <0x1>;
> +		bias-pull-up = <0x1>;
> +		input-schmitt-enable;
> +	};
> +
> +	pinctrl_i2c1: i2c1grp {
> +		pinmux = <
> +			MX6SLL_PAD_I2C1_SCL__I2C1_SCL
> +			MX6SLL_PAD_I2C1_SDA__I2C1_SDA
> +		>;
> +		slew-rate = <0x1>;
> +		drive-strength = <0x6>;
> +		fsl,pin-speed = <0x2>;
> +		drive-open-drain;
> +		bias-pull-up = <0x2>;
> +		input-schmitt-enable;
> +		input-enable;
> +	};
> +};
> +
> +&uart1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart1>;
> +	status = "okay";
> +};
> +
> +&usdhc1 {
> +	pinctrl-names = "default", "state_100mhz", "state_200mhz";
> +	pinctrl-0 = <&pinctrl_usdhc1_data>, <&pinctrl_usdhc1_clk>;
> +	pinctrl-1 = <&pinctrl_usdhc1_data_100mhz>, <&pinctrl_usdhc1_clk_100mhz>;
> +	pinctrl-2 = <&pinctrl_usdhc1_data_200mhz>, <&pinctrl_usdhc1_clk_200mhz>;
> +	cd-gpios = <&gpio4 7 GPIO_ACTIVE_LOW>;
> +	wp-gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
> +	keep-power-in-suspend;
> +	wakeup-source;
> +	vmmc-supply = <&reg_sd1_vmmc>;
> +	status = "okay";
> +};
> +
> +&usbotg1 {
> +	vbus-supply = <&reg_usb_otg1_vbus>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usbotg1>;
> +	disable-over-current;
> +	srp-disable;
> +	hnp-disable;
> +	adp-disable;
> +	status = "okay";
> +};
> +
> +&usbotg2 {
> +	vbus-supply = <&reg_usb_otg2_vbus>;
> +	dr_mode = "host";
> +	disable-over-current;
> +	status = "okay";
> +};
> -- 
> 1.9.1
> 
> 
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel



More information about the linux-arm-kernel mailing list