[PATCH v4 1/6] dt-bindings: update the Allwinner GPADC device tree binding for H3

Icenowy Zheng icenowy at aosc.io
Mon Sep 18 00:36:43 PDT 2017



于 2017年9月18日 GMT+08:00 下午3:33:36, Maxime Ripard <maxime.ripard at free-electrons.com> 写到:
>On Thu, Sep 14, 2017 at 10:52:46PM +0800, Icenowy Zheng wrote:
>> Allwinner H3 features a thermal sensor like the one in A33, but has
>its
>> register re-arranged, the clock divider moved to CCU (originally the
>> clock divider is in ADC) and added a pair of bus clock and reset.
>> 
>> Update the binding document to cover H3.
>> 
>> Signed-off-by: Icenowy Zheng <icenowy at aosc.io>
>> Reviewed-by: Chen-Yu Tsai <wens at csie.org>
>> ---
>> Changes in v4:
>> - Add nvmem calibration data (not yet used by the driver)
>> Changes in v3:
>> - Clock name changes.
>> - Example node name changes.
>> - Add interupts (not yet used by the driver).
>> 
>>  .../devicetree/bindings/mfd/sun4i-gpadc.txt        | 30
>++++++++++++++++++++--
>>  1 file changed, 28 insertions(+), 2 deletions(-)
>> 
>> diff --git a/Documentation/devicetree/bindings/mfd/sun4i-gpadc.txt
>b/Documentation/devicetree/bindings/mfd/sun4i-gpadc.txt
>> index badff3611a98..6c470d584bf9 100644
>> --- a/Documentation/devicetree/bindings/mfd/sun4i-gpadc.txt
>> +++ b/Documentation/devicetree/bindings/mfd/sun4i-gpadc.txt
>> @@ -4,12 +4,26 @@ The Allwinner SoCs all have an ADC that can also
>act as a thermal sensor
>>  and sometimes as a touchscreen controller.
>>  
>>  Required properties:
>> -  - compatible: "allwinner,sun8i-a33-ths",
>> +  - compatible: must contain one of the following compatibles:
>> +		- "allwinner,sun8i-a33-ths"
>> +		- "allwinner,sun8i-h3-ths"
>>    - reg: mmio address range of the chip,
>>    - #thermal-sensor-cells: shall be 0,
>>    - #io-channel-cells: shall be 0,
>>  
>> -Example:
>> +Optional properties:
>> +  - nvmem-cells: A phandle to the calibration data provided by a
>nvmem device.
>> +                 If unspecified default values shall be used.
>> +  - nvmem-cell-names: Should be "calibration-data"
>
>I'd prefer to have which sensor it applies to here. It wouldn't change
>anything for the H3, but it definitely does for example for the A83t
>that has two sensors, one for each cluster, and one for the GPU, each
>with calibration data.
>
>What about cluster0-calibration?

The calibration data is in fact a 2 word (8 bytes) zone,
which is reserved for 4 sensors on all SoCs, even on H3.
It's half word per sensor.

I prefer to just assume a 2 word cell for every SoC.

>
>> +
>> +Required properties for the following compatibles:
>> +		- "allwinner,sun8i-h3-ths"
>> +  - clocks: the bus clock and the input clock of the ADC,
>> +  - clock-names: should be "bus" and "mod",
>> +  - resets: the bus reset of the ADC,
>> +  - interrupts: the sampling interrupt of the ADC,
>
>For resets and interrupts, you should list all of them. If there's
>only one, then there's no point telling which one it is.
>
>
>Thanks,
>Maxime



More information about the linux-arm-kernel mailing list