[PATCH] ARM: DTS armada: Add support for 2 more mvebu model

Ansuel Smith ansuelsmth at gmail.com
Fri Mar 3 09:07:35 PST 2017


This patch add support for 2 Linksys router model
(shelby and rango). With this we now support all
the mvebu board on the market.

Signed-off-by: Imre Kaloz <kaloz at openwrt.org>
Signed-off-by: Álvaro Fernández Rojas <noltari at gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth at gmail.com>
---
 arch/arm/boot/dts/armada-385-linksys-rango.dts  | 443 ++++++++++++++++++++++++
 arch/arm/boot/dts/armada-385-linksys-shelby.dts | 115 ++++++
 2 files changed, 558 insertions(+)
 create mode 100644 arch/arm/boot/dts/armada-385-linksys-rango.dts
 create mode 100644 arch/arm/boot/dts/armada-385-linksys-shelby.dts

diff --git a/arch/arm/boot/dts/armada-385-linksys-rango.dts b/arch/arm/boot/dts/armada-385-linksys-rango.dts
new file mode 100644
index 0000000..61f4592
--- /dev/null
+++ b/arch/arm/boot/dts/armada-385-linksys-rango.dts
@@ -0,0 +1,443 @@
+/*
+ * Device Tree file for the Linksys WRT3200ACM (Rango)
+ *
+ * Copyright (C) 2016 Imre Kaloz <kaloz at openwrt.org>
+ *
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is licensed under the terms of the GNU General Public
+ *     License version 2.  This program is licensed "as is" without
+ *     any warranty of any kind, whether express or implied.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "armada-385.dtsi"
+
+/ {
+	model = "Linksys WRT3200ACM";
+	compatible = "linksys,rango", "linksys,armada385", "marvell,armada385",
+		     "marvell,armada380";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>; /* 512 MB */
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+			  MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
+			  MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000
+			  MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000
+			  MBUS_ID(0x0c, 0x04) 0 0xf1200000 0x100000>;
+
+		internal-regs {
+
+			spi at 10600 {
+				status = "disabled";
+			};
+
+			i2c at 11000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&i2c0_pins>;
+				status = "okay";
+
+				tmp421 at 4c {
+					compatible = "ti,tmp421";
+					reg = <0x4c>;
+				};
+
+				pca9635 at 68 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					compatible = "nxp,pca9635";
+					reg = <0x68>;
+
+					wan_amber at 0 {
+						label = "rango:amber:wan";
+						reg = <0x0>;
+					};
+
+					wan_white at 1 {
+						label = "rango:white:wan";
+						reg = <0x1>;
+					};
+
+					usb2 at 5 {
+						label = "rango:white:usb2";
+						reg = <0x5>;
+					};
+
+					usb3_1 at 6 {
+						label = "rango:white:usb3_1";
+						reg = <0x6>;
+					};
+
+					usb3_2 at 7 {
+						label = "rango:white:usb3_2";
+						reg = <0x7>;
+					};
+
+					wps_white at 8 {
+						label = "rango:white:wps";
+						reg = <0x8>;
+					};
+
+					wps_amber at 9 {
+						label = "rango:amber:wps";
+						reg = <0x9>;
+					};
+				};
+			};
+
+			/* J10: VCC, NC, RX, NC, TX, GND  */
+			serial at 12000 {
+				status = "okay";
+			};
+
+			ethernet at 70000 {
+				status = "okay";
+				phy-mode = "rgmii-id";
+				buffer-manager = <&bm>;
+				bm,pool-long = <0>;
+				bm,pool-short = <3>;
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+
+			ethernet at 34000 {
+				status = "okay";
+				phy-mode = "sgmii";
+				buffer-manager = <&bm>;
+				bm,pool-long = <2>;
+				bm,pool-short = <3>;
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+
+			mdio {
+				status = "okay";
+			};
+
+			bm at c8000 {
+				status = "okay";
+			};
+
+			sata at a8000 {
+				status = "okay";
+			};
+
+			/* USB part of the eSATA/USB 2.0 port */
+			usb at 58000 {
+				status = "okay";
+			};
+
+			usb3 at f8000 {
+				status = "okay";
+				usb-phy = <&usb3_phy>;
+			};
+
+			flash at d0000 {
+				status = "okay";
+				num-cs = <1>;
+				marvell,nand-keep-config;
+				marvell,nand-enable-arbiter;
+				nand-on-flash-bbt;
+
+				partition at 0 {
+					label = "u-boot";
+					reg = <0x0000000 0x200000>;  /* 2MB */
+					read-only;
+				};
+
+				partition at 200000 {
+					label = "u_env";
+					reg = <0x200000 0x20000>;    /* 128KB */
+				};
+
+				partition at 220000 {
+					label = "s_env";
+					reg = <0x220000 0x40000>;    /* 256KB */
+				};
+
+				partition at 7e0000 {
+					label = "devinfo";
+					reg = <0x7e0000 0x40000>;   /* 256KB */
+					read-only;
+				};
+
+				partition at 820000 {
+					label = "sysdiag";
+					reg = <0x820000 0x1e0000>;   /* 1920KB */
+					read-only;
+				};
+
+				/* kernel1 overlaps with rootfs1 by design */
+				partition at a00000 {
+					label = "kernel1";
+					reg = <0xa00000 0x5000000>;  /* 80MB */
+				};
+
+				partition at 1000000 {
+					label = "rootfs1";
+					reg = <0x1000000 0x4a00000>;  /* 74MB */
+				};
+
+				/* kernel2 overlaps with rootfs2 by design */
+				partition at 5a00000 {
+					label = "kernel2";
+					reg = <0x5a00000 0x5000000>; /* 80MB */
+				};
+
+				partition at 6000000 {
+					label = "rootfs2";
+					reg = <0x6000000 0x4a00000>; /* 74MB */
+				};
+
+				/*
+				 * 86MB, last MB is for the BBT, not writable
+				 */
+				partition at aa00000 {
+					label = "syscfg";
+					reg = <0xaa00000 0x5600000>;
+				};
+
+				/*
+				 * Unused area between "s_env" and "devinfo".
+				 * Moved here because otherwise the renumbered
+				 * partitions would break the bootloader
+				 * supplied bootargs
+				 */
+				partition at 180000 {
+					label = "unused_area";
+					reg = <0x260000 0x5c0000>;   /* 5.75MB */
+				};
+			};
+		};
+
+		bm-bppi {
+			status = "okay";
+		};
+
+		pcie-controller {
+			status = "okay";
+
+			pcie at 1,0 {
+				/* Marvell 88W8964, 5GHz-only */
+				status = "okay";
+
+				mwlwifi {
+					marvell,2ghz = <0>;
+					marvell,chainmask = <4 4>;
+				};
+
+			};
+
+			pcie at 2,0 {
+				/* Marvell 88W8964, 2GHz-only */
+				status = "okay";
+
+				mwlwifi {
+					marvell,5ghz = <0>;
+					marvell,chainmask = <4 4>;
+				};
+
+			};
+		};
+	};
+
+	usb3_phy: usb3_phy {
+		compatible = "usb-nop-xceiv";
+		vcc-supply = <&reg_xhci0_vbus>;
+	};
+
+	reg_xhci0_vbus: xhci0-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&xhci0_vbus_pins>;
+		regulator-name = "xhci0-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&gpio1 15 GPIO_ACTIVE_HIGH>;
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&reset_key_pin &wps_key_pin>;
+		pinctrl-names = "default";
+
+		button at 1 {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
+		};
+
+		button at 2 {
+			label = "Factory Reset Button";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&power_led_pin &sata_led_pin &wlan_2g_led_pin &wlan_5g_led_pin>;
+		pinctrl-names = "default";
+
+		sata {
+			label = "rango:white:sata";
+			gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "disk-activity";
+		};
+
+		wlan_2g {
+			label = "rango:white:wlan_2g";
+			gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+		};
+
+		wlan_5g {
+			label = "rango:white:wlan_5g";
+			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+		};
+
+		power {
+			label = "rango:white:power";
+			gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+	};
+
+	dsa at 0 {
+		compatible = "marvell,dsa";
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		dsa,ethernet = <&eth2>;
+		dsa,mii-bus = <&mdio>;
+
+		switch at 0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0>;	/* MDIO address 0, switch 0 in tree */
+
+			port at 0 {
+				reg = <0>;
+				label = "lan4";
+			};
+
+			port at 1 {
+				reg = <1>;
+				label = "lan3";
+			};
+
+			port at 2 {
+				reg = <2>;
+				label = "lan2";
+			};
+
+			port at 3 {
+				reg = <3>;
+				label = "lan1";
+			};
+
+			port at 4 {
+				reg = <4>;
+				label = "wan";
+			};
+
+			port at 5 {
+				reg = <5>;
+				label = "cpu";
+			};
+		};
+	};
+
+	mvsw61xx {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "marvell,88e6352";
+		status = "okay";
+		reg = <0x10>;
+
+		mii-bus = <&mdio>;
+		cpu-port-0 = <5>;
+		cpu-port-1 = <6>;
+	};
+
+};
+
+&pinctrl {
+	sata_led_pin: sata-led-pin {
+		marvell,pins = "mpp21";
+		marvell,function = "gpio";
+	};
+
+	wps_key_pin: wps-key-pin {
+		marvell,pins = "mpp24";
+		marvell,function = "gpio";
+	};
+
+	reset_key_pin: reset-key-pin {
+		marvell,pins = "mpp29";
+		marvell,function = "gpio";
+	};
+
+	wlan_2g_led_pin: wlan-2g-led-pin {
+		marvell,pins = "mpp45";
+		marvell,function = "gpio";
+	};
+
+	wlan_5g_led_pin: wlan-5g-led-pin {
+		marvell,pins = "mpp46";
+		marvell,function = "gpio";
+	};
+
+	xhci0_vbus_pins: xhci0-vbus-pins {
+		marvell,pins = "mpp47";
+		marvell,function = "gpio";
+	};
+
+	power_led_pin: power-led-pin {
+		marvell,pins = "mpp56";
+		marvell,function = "gpio";
+	};
+};
diff --git a/arch/arm/boot/dts/armada-385-linksys-shelby.dts b/arch/arm/boot/dts/armada-385-linksys-shelby.dts
new file mode 100644
index 0000000..f8dd193
--- /dev/null
+++ b/arch/arm/boot/dts/armada-385-linksys-shelby.dts
@@ -0,0 +1,115 @@
+/*
+ * Device Tree file for the Linksys WRT1900ACS (Shelby)
+ *
+ * Copyright (C) 2015 Imre Kaloz <kaloz at openwrt.org>
+ *
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is licensed under the terms of the GNU General Public
+ *     License version 2.  This program is licensed "as is" without
+ *     any warranty of any kind, whether express or implied.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "armada-385-linksys.dtsi"
+
+/ {
+	model = "Linksys WRT1900ACS";
+	compatible = "linksys,shelby", "linksys,armada385", "marvell,armada385",
+		     "marvell,armada380";
+
+	soc {
+		internal-regs{
+			i2c at 11000 {
+
+				pca9635 at 68 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+					wan_amber at 0 {
+						label = "shelby:amber:wan";
+						reg = <0x0>;
+					};
+
+					wan_white at 1 {
+						label = "shelby:white:wan";
+						reg = <0x1>;
+					};
+
+					wlan_2g at 2 {
+						label = "shelby:white:wlan_2g";
+						reg = <0x2>;
+					};
+
+					wlan_5g at 3 {
+						label = "shelby:white:wlan_5g";
+						reg = <0x3>;
+					};
+
+					usb2 at 5 {
+						label = "shelby:white:usb2";
+						reg = <0x5>;
+					};
+
+					usb3_1 at 6 {
+						label = "shelby:white:usb3_1";
+						reg = <0x6>;
+					};
+
+					usb3_2 at 7 {
+						label = "shelby:white:usb3_2";
+						reg = <0x7>;
+					};
+
+					wps_white at 8 {
+						label = "shelby:white:wps";
+						reg = <0x8>;
+					};
+
+					wps_amber at 9 {
+						label = "shelby:amber:wps";
+						reg = <0x9>;
+					};
+				};
+			};
+		};
+	};
+
+	gpio-leds {
+		power {
+			label = "shelby:white:power";
+		};
+
+		sata {
+			label = "shelby:white:sata";
+			linux,default-trigger = "disk-activity";
+		};
+	};
+};
-- 
2.7.4




More information about the linux-arm-kernel mailing list