[PATCH v3 06/24] ARM: dts: imx6-sabrelite: add OV5642 and OV5640 camera sensors

Philipp Zabel p.zabel at pengutronix.de
Fri Jan 13 04:03:41 PST 2017


Am Freitag, den 06.01.2017, 18:11 -0800 schrieb Steve Longerbeam:
> Enables the OV5642 parallel-bus sensor, and the OV5640 MIPI CSI-2 sensor.
> Both hang off the same i2c2 bus, so they require different (and non-
> default) i2c slave addresses.
> 
> The OV5642 connects to the parallel-bus mux input port on ipu1_csi0_mux.
> 
> The OV5640 connects to the input port on the MIPI CSI-2 receiver on
> mipi_csi. It is set to transmit over MIPI virtual channel 1.
> 
> Signed-off-by: Steve Longerbeam <steve_longerbeam at mentor.com>
> ---
>  arch/arm/boot/dts/imx6dl-sabrelite.dts   |   5 ++
>  arch/arm/boot/dts/imx6q-sabrelite.dts    |   6 ++
>  arch/arm/boot/dts/imx6qdl-sabrelite.dtsi | 118 +++++++++++++++++++++++++++++++
>  3 files changed, 129 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/imx6dl-sabrelite.dts b/arch/arm/boot/dts/imx6dl-sabrelite.dts
> index 0f06ca5..fec2524 100644
> --- a/arch/arm/boot/dts/imx6dl-sabrelite.dts
> +++ b/arch/arm/boot/dts/imx6dl-sabrelite.dts
> @@ -48,3 +48,8 @@
>  	model = "Freescale i.MX6 DualLite SABRE Lite Board";
>  	compatible = "fsl,imx6dl-sabrelite", "fsl,imx6dl";
>  };
> +
> +&ipu1_csi1_from_ipu1_csi1_mux {
> +	data-lanes = <0 1>;
> +	clock-lanes = <2>;
> +};
> diff --git a/arch/arm/boot/dts/imx6q-sabrelite.dts b/arch/arm/boot/dts/imx6q-sabrelite.dts
> index 66d10d8..9e2d26d 100644
> --- a/arch/arm/boot/dts/imx6q-sabrelite.dts
> +++ b/arch/arm/boot/dts/imx6q-sabrelite.dts
> @@ -52,3 +52,9 @@
>  &sata {
>  	status = "okay";
>  };
> +
> +&ipu1_csi1_from_mipi_vc1 {
> +	data-lanes = <0 1>;
> +	clock-lanes = <2>;
> +};
> +
> diff --git a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
> index 795b5a5..bca9fed 100644
> --- a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
> @@ -39,6 +39,8 @@
>   *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
>   *     OTHER DEALINGS IN THE SOFTWARE.
>   */
> +
> +#include <dt-bindings/clock/imx6qdl-clock.h>
>  #include <dt-bindings/gpio/gpio.h>
>  #include <dt-bindings/input/input.h>
>  
> @@ -96,6 +98,15 @@
>  		};
>  	};
>  
> +	mipi_xclk: mipi_xclk {
> +		compatible = "pwm-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <22000000>;
> +		clock-output-names = "mipi_pwm3";
> +		pwms = <&pwm3 0 45>; /* 1 / 45 ns = 22 MHz */
> +		status = "okay";
> +	};
> +
>  	gpio-keys {
>  		compatible = "gpio-keys";
>  		pinctrl-names = "default";
> @@ -220,6 +231,22 @@
>  	};
>  };
>  
> +&ipu1_csi0_from_ipu1_csi0_mux {
> +	bus-width = <8>;
> +	data-shift = <12>; /* Lines 19:12 used */
> +	hsync-active = <1>;
> +	vync-active = <1>;
> +};
> +
> +&ipu1_csi0_mux_from_parallel_sensor {
> +	remote-endpoint = <&ov5642_to_ipu1_csi0_mux>;
> +};
> +
> +&ipu1_csi0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_ipu1_csi0>;
> +};
> +
>  &audmux {
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&pinctrl_audmux>;
> @@ -299,6 +326,52 @@
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&pinctrl_i2c2>;
>  	status = "okay";
> +
> +	ov5640: camera at 40 {
> +		compatible = "ovti,ov5640";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_ov5640>;
> +		clocks = <&mipi_xclk>;
> +		clock-names = "xclk";
> +		reg = <0x40>;
> +		xclk = <22000000>;

This is superfluous, you can use clk_get_rate on mipi_xclk.

> +		reset-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>; /* NANDF_D5 */
> +		pwdn-gpios = <&gpio6 9 GPIO_ACTIVE_HIGH>; /* NANDF_WP_B */
> +
> +		port {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			ov5640_to_mipi_csi: endpoint at 1 {
> +				reg = <1>;
> +				remote-endpoint = <&mipi_csi_from_mipi_sensor>;
> +				data-lanes = <0 1>;
> +				clock-lanes = <2>;
> +			};
> +		};
> +	};
> +
> +	ov5642: camera at 42 {
> +		compatible = "ovti,ov5642";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_ov5642>;
> +		clocks = <&clks IMX6QDL_CLK_CKO2>;
> +		clock-names = "xclk";
> +		reg = <0x42>;
> +		xclk = <24000000>;

Same here, use assigned-clock-rates on IMX6QDL_CLK_CKO2 if necessary.

> +		reset-gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
> +		pwdn-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
> +		gp-gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>;
> +
> +		port {
> +			ov5642_to_ipu1_csi0_mux: endpoint {
> +				remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
> +				bus-width = <8>;
> +				hsync-active = <1>;
> +				vsync-active = <1>;
> +			};
> +		};
> +	};
>  };
>  
>  &i2c3 {
> @@ -412,6 +485,23 @@
>  			>;
>  		};
>  
> +		pinctrl_ipu1_csi0: ipu1csi0grp {
> +			fsl,pins = <
> +				MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12    0x1b0b0
> +				MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13    0x1b0b0
> +				MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14    0x1b0b0
> +				MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15    0x1b0b0
> +				MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16    0x1b0b0
> +				MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17    0x1b0b0
> +				MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18    0x1b0b0
> +				MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19    0x1b0b0
> +				MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK   0x1b0b0
> +				MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC      0x1b0b0
> +				MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC     0x1b0b0
> +				MX6QDL_PAD_CSI0_DATA_EN__IPU1_CSI0_DATA_EN 0x1b0b0
> +			>;
> +		};
> +
>  		pinctrl_j15: j15grp {
>  			fsl,pins = <
>  				MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10
> @@ -445,6 +535,22 @@
>  			>;
>  		};
>  
> +		pinctrl_ov5640: ov5640grp {
> +			fsl,pins = <
> +				MX6QDL_PAD_NANDF_D5__GPIO2_IO05   0x000b0
> +				MX6QDL_PAD_NANDF_WP_B__GPIO6_IO09 0x0b0b0
> +			>;
> +		};
> +
> +		pinctrl_ov5642: ov5642grp {
> +			fsl,pins = <
> +				MX6QDL_PAD_SD1_DAT0__GPIO1_IO16 0x1b0b0
> +				MX6QDL_PAD_GPIO_6__GPIO1_IO06   0x1b0b0
> +				MX6QDL_PAD_GPIO_8__GPIO1_IO08   0x130b0
> +				MX6QDL_PAD_GPIO_3__CCM_CLKO2    0x000b0
> +			>;
> +		};
> +
>  		pinctrl_pwm1: pwm1grp {
>  			fsl,pins = <
>  				MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x1b0b1
> @@ -601,3 +707,15 @@
>  	vmmc-supply = <&reg_3p3v>;
>  	status = "okay";
>  };
> +
> +&mipi_csi {
> +        status = "okay";
> +};
> +
> +/* Incoming port from sensor */
> +&mipi_csi_from_mipi_sensor {
> +        remote-endpoint = <&ov5640_to_mipi_csi>;
> +        data-lanes = <0 1>;
> +        clock-lanes = <2>;
> +};
> +

regards
Philipp




More information about the linux-arm-kernel mailing list