[PATCH V2 1/3] arm64: dts: Add basic DT to support Spreadtrum's SP9860G
Chunyan Zhang
zhang.lyra at gmail.com
Wed Feb 22 22:20:26 PST 2017
[...]
>>> > +
>>> > + soc {
>>> > + soc_funnel: funnel at 10001000 {
>>>
>>> There is no need for a label ("soc_funnel) before the device name if that
>>> device is not referenced elsewhere in the DTS. The same comment applies to most
>>> of the component listed below.
>>>
>>
>> OK, I will remove these labels from this DT.
>> And there's another issue I'd like to discuss with you, do you think which way is better:
>> 1) use class name which can represent this kind of components as device node name in DT, e.g.
>> funnel at ... {
>>
>> }
>> replicator at ... {
>>
>> }
>> etb at ... {
>>
>> }
>> etf at ...
>> etm at ...
>> stm at ...
>>
>> 2) use more descriptive device name for those which are more than one on
>> a SoC, e.g.
>> soc-funnel at ... {
>>
>> }
>> cluster0-funnel at ... {
>>
>> }
>> cluster1-funnel at ... {
>>
>> }
>>
>> I noticed Juno use the 2), would you suggest that way?
>
> It is better to describe the HW component themselves rather than where
> they are in the topology - the address of the component will make sure
> the names are unique. So just the component type (etm, funnel,
> replicator, ....) and the address they are located at.
>
OK. And to avoid making other person confused in the future, is it
better to revise juno-base.dtsi according to this convention?
Thanks,
Chunyan
>>
>> Thanks,
>> Chunyan
>>
>>> > + compatible = "arm,coresight-funnel", "arm,primecell";
>>> > + reg = <0 0x10001000 0 0x1000>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > + ports {
>>> > + #address-cells = <1>;
>>> > + #size-cells = <0>;
>>> > +
>>> > + port at 0 {
>>> > + reg = <0>;
>>> > + soc_funnel_out_port: endpoint {
>>> > + remote-endpoint = <&etb_in>;
>>> > + };
>>> > + };
>>> > +
>>> > + port at 1 {
>>> > + reg = <0>;
>>> > + soc_funnel_in_port: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint =
>>> > + <&main_funnel_out_port>;
>>> > + };
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etb at 10003000 {
>>> > + compatible = "arm,coresight-tmc", "arm,primecell";
>>> > + reg = <0 0x10003000 0 0x1000>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > + port {
>>> > + etb_in: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint =
>>> > + <&soc_funnel_out_port>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + cluster0_funnel: funnel at 11001000 {
>>> > + compatible = "arm,coresight-funnel", "arm,primecell";
>>> > + reg = <0 0x11001000 0 0x1000>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > + ports {
>>> > + #address-cells = <1>;
>>> > + #size-cells = <0>;
>>> > +
>>> > + port at 0 {
>>> > + reg = <0>;
>>> > + cluster0_funnel_out_port: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster0_etf_in>;
>>> > + };
>>> > + };
>>> > +
>>> > + port at 1 {
>>> > + reg = <0>;
>>> > + cluster0_funnel_in_port0: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint = <&etm0_out>;
>>> > + };
>>> > + };
>>> > +
>>> > + port at 2 {
>>> > + reg = <1>;
>>> > + cluster0_funnel_in_port1: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint = <&etm1_out>;
>>> > + };
>>> > + };
>>> > +
>>> > + port at 3 {
>>> > + reg = <2>;
>>> > + cluster0_funnel_in_port2: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint = <&etm2_out>;
>>> > + };
>>> > + };
>>> > +
>>> > + port at 4 {
>>> > + reg = <4>;
>>> > + cluster0_funnel_in_port3: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint = <&etm3_out>;
>>> > + };
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + cluster1_funnel: funnel at 11002000 {
>>> > + compatible = "arm,coresight-funnel", "arm,primecell";
>>> > + reg = <0 0x11002000 0 0x1000>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > + ports {
>>> > + #address-cells = <1>;
>>> > + #size-cells = <0>;
>>> > +
>>> > + port at 0 {
>>> > + reg = <0>;
>>> > + cluster1_funnel_out_port: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster1_etf_in>;
>>> > + };
>>> > + };
>>> > +
>>> > + port at 1 {
>>> > + reg = <0>;
>>> > + cluster1_funnel_in_port0: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint = <&etm4_out>;
>>> > + };
>>> > + };
>>> > +
>>> > + port at 2 {
>>> > + reg = <1>;
>>> > + cluster1_funnel_in_port1: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint = <&etm5_out>;
>>> > + };
>>> > + };
>>> > +
>>> > + port at 3 {
>>> > + reg = <2>;
>>> > + cluster1_funnel_in_port2: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint = <&etm6_out>;
>>> > + };
>>> > + };
>>> > +
>>> > + port at 4 {
>>> > + reg = <3>;
>>> > + cluster1_funnel_in_port3: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint = <&etm7_out>;
>>> > + };
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + cluster0_etf: etf at 11003000 {
>>> > + compatible = "arm,coresight-tmc", "arm,primecell";
>>> > + reg = <0 0x11003000 0 0x1000>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port at 0 {
>>> > + cluster0_etf_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&main_funnel_in_port0>;
>>> > + };
>>> > + };
>>> > +
>>> > + port at 1 {
>>> > + cluster0_etf_in: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint =
>>> > + <&cluster0_funnel_out_port>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + cluster1_etf: etf at 11004000 {
>>> > + compatible = "arm,coresight-tmc", "arm,primecell";
>>> > + reg = <0 0x11004000 0 0x1000>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port at 0 {
>>> > + cluster1_etf_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&main_funnel_in_port1>;
>>> > + };
>>> > + };
>>> > +
>>> > + port at 1 {
>>> > + cluster1_etf_in: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint =
>>> > + <&cluster1_funnel_out_port>;
>>> > + };
>>> > + };
>>> > + };
>>>
>>> When more than one port is present it is customary to add another level of
>>> imbrication like it is done for funnels above:
>>> "ports {"
>>> port at 0 {
>>> ...
>>> port at 1 {
>>> ...
>>> }
>>>
>>> The same comment applies to both etf.
>>>
>>
>> OK.
>>
>>> > +
>>> > + main_funnel: funnel at 11005000 {
>>> > + compatible = "arm,coresight-funnel", "arm,primecell";
>>> > + reg = <0 0x11005000 0 0x1000>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + ports {
>>> > + #address-cells = <1>;
>>> > + #size-cells = <0>;
>>> > +
>>> > + port at 0 {
>>> > + reg = <0>;
>>> > + main_funnel_out_port: endpoint {
>>> > + remote-endpoint =
>>> > + <&soc_funnel_in_port>;
>>> > + };
>>> > + };
>>> > +
>>> > + port at 1 {
>>> > + reg = <0>;
>>> > + main_funnel_in_port0: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint =
>>> > + <&cluster0_etf_out>;
>>> > + };
>>> > + };
>>> > +
>>> > + port at 2 {
>>> > + reg = <1>;
>>> > + main_funnel_in_port1: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint =
>>> > + <&cluster1_etf_out>;
>>> > + };
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etm at 11440000 {
>>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>>> > + reg = <0 0x11440000 0 0x1000>;
>>> > + cpu = <&CPU0>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port {
>>> > + etm0_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster0_funnel_in_port0>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etm at 11540000 {
>>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>>> > + reg = <0 0x11540000 0 0x1000>;
>>> > + cpu = <&CPU1>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port {
>>> > + etm1_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster0_funnel_in_port1>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etm at 11640000 {
>>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>>> > + reg = <0 0x11640000 0 0x1000>;
>>> > + cpu = <&CPU2>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port {
>>> > + etm2_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster0_funnel_in_port2>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etm at 11740000 {
>>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>>> > + reg = <0 0x11740000 0 0x1000>;
>>> > + cpu = <&CPU3>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port {
>>> > + etm3_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster0_funnel_in_port3>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etm at 11840000 {
>>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>>> > + reg = <0 0x11840000 0 0x1000>;
>>> > + cpu = <&CPU4>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port {
>>> > + etm4_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster1_funnel_in_port0>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etm at 11940000 {
>>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>>> > + reg = <0 0x11940000 0 0x1000>;
>>> > + cpu = <&CPU5>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port {
>>> > + etm5_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster1_funnel_in_port1>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etm at 11a40000 {
>>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>>> > + reg = <0 0x11a40000 0 0x1000>;
>>> > + cpu = <&CPU6>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port {
>>> > + etm6_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster1_funnel_in_port2>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etm at 11b40000 {
>>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>>> > + reg = <0 0x11b40000 0 0x1000>;
>>> > + cpu = <&CPU7>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port {
>>> > + etm7_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster1_funnel_in_port3>;
>>> > + };
>>> > + };
>>> > + };
>>> > + };
>>> > +};
[...]
>>> >
>>> > _______________________________________________
>>> > linux-arm-kernel mailing list
>>> > linux-arm-kernel at lists.infradead.org
>>> > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>> --
>> To unsubscribe from this list: send the line "unsubscribe devicetree" in
>> the body of a message to majordomo at vger.kernel.org
>> More majordomo info at http://vger.kernel.org/majordomo-info.html
More information about the linux-arm-kernel
mailing list